Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART)
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0245023 ECD SYSTEM(for i-ART) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P0405  Exhaust Gas Recirculation Sensor "A" Circuit Low  P0406  Exhaust Gas Recirculation Sensor "A" Circuit High  


DESCRIPTION

The EGR valve position sensor is mounted on the electric EGR control valve assembly and used for detecting the EGR valve angle. The EGR valve angle detected by the sensor is sent to the ECM as feedback. The ECM then regulates the EGR valve angle in accordance with engine running conditions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low EGR valve position sensor output voltage is less than 0.2 V for 2 seconds.
(1 trip detection logic)
·

Open or short in EGR valve position sensor circuit

·

Electric EGR control valve assembly (EGR valve position sensor)

·

ECM


Comes on DTC stored
P0406 Exhaust Gas Recirculation Sensor "A" Circuit High EGR valve position sensor output voltage is higher than 4.8 V for 2 seconds.
(1 trip detection logic)
·

Open or short in EGR valve position sensor circuit

·

Electric EGR control valve assembly (EGR valve position sensor)

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0405 Engine switch on (IG) for 2 seconds or more
P0406

MONITOR DESCRIPTION

When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.2 to 4.8 V for more than 2 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ECM (EGR VALVE POSITION SENSOR VOLTAGE)
a.
A368773C16
1.281,0.802 1.677,1.073 0.396,0.271 1.146,2.323 1.333,1.688 true 2.073,2.333 1.417,1.646 true 1.354,0.854 1.813,1.052 0.458,0.198 10 false C40 0.719,2.417 1.406,2.635 0.688,0.219 10 false 31 (VCEG) 1.906,2.427 2.792,2.667 0.885,0.24 10 false 24 (EEGL) 0.167,0.177 0.625,0.375 0.458,0.198 10 false *a
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C40-31 (VCEG) - C40-24 (EEGL) Engine switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.INSPECT EGR VALVE POSITION SENSOR (EGLS VOLTAGE)

NG

10.REPLACE ECM
2.INSPECT EGR VALVE POSITION SENSOR (EGLS VOLTAGE)
a.
A368773C17
1.26,0.823 1.656,1.094 0.396,0.271 1.031,2.313 1.365,1.635 true 2.021,2.323 1.417,1.635 true 1.333,0.875 1.792,1.073 0.458,0.198 10 false C40 0.646,2.417 1.333,2.635 0.688,0.219 10 false 25 (EGLS) 1.917,2.417 2.802,2.656 0.885,0.24 10 false 24 (EEGL) 0.146,0.156 0.604,0.354 0.458,0.198 10 false *a
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C40-25 (EGLS) - C40-24 (EEGL) Engine switch on (IG) 0.6 to 1.4 V



Result:
Proceed to
OK
NG



OK

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

4.CHECK HARNESS AND CONNECTOR
3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the engine switch off and wait for 30 seconds or more.


d.

Turn the engine switch on (IG) for 2 seconds or more.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

4.CHECK HARNESS AND CONNECTOR
a.
A351103C11
1.448,0.594 1.917,0.938 0.469,0.344 0.844,2.583 1.083,1.917 true 1.948,2.604 1.74,1.917 true 1.563,0.688 2.021,0.885 0.458,0.198 10 false C37 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a 0.74,2.646 1.198,2.844 0.458,0.198 10 false E2 1.896,2.646 2.354,2.844 0.458,0.198 10 false VC
*a Front view of wire harness connector
(to Electric EGR Control Valve Assembly)


Disconnect the electric EGR control valve assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C37-3 (VC) - C37-1 (E2) Engine switch on (IG) 4.5 to 5.5 V



c.

Reconnect the electric EGR control valve assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
a.

Disconnect the electric EGR control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C37-3 (VC) - C40-31 (VCEG) Always Below 1 Ω
C37-2 (VTA) - C40-25 (EGLS) Always Below 1 Ω
C37-1 (E2) - C40-24 (EEGL) Always Below 1 Ω
C37-3 (VC) or C40-31 (VCEG) - Body ground and other terminals Always 10 kΩ or higher
C37-2 (VTA) or C40-25 (EGLS) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the electric EGR control valve assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

6.CHECK ECM (CHECK RESISTANCE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the electric EGR control valve assembly connector.


b.
A351103C12
1.531,0.542 1.938,0.865 0.406,0.323 0.781,2.563 1.083,1.906 true 1.292,2.552 1.396,1.906 true 1.917,2.583 1.729,1.927 true 0.271,0.24 0.583,0.438 0.313,0.198 10 false *a 1.615,0.635 2.073,0.844 0.458,0.208 10 false C37 1.177,2.615 1.542,2.813 0.365,0.198 10 false VTA 0.688,2.615 1,2.813 0.313,0.198 10 false E2 1.875,2.625 2.24,2.823 0.365,0.198 10 false VC
*a Front view of wire harness connector
(to Electric EGR Control Valve Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C37-3 (VC) - C37-2 (VTA) Engine switch off No short or open circuit
C37-2 (VTA) - C37-1 (E2)



c.

Reconnect the electric EGR control valve assembly connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY

NG

10.REPLACE ECM
7.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EGR VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the engine switch on (IG) for 2 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED