Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART)
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0245023 ECD SYSTEM(for i-ART) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the ECM detects the starter signal (STA signal) and performs engine control when the engine starts.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) or more for more than 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.4 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
·

ST NO. 1 relay circuit

·

Park/Neutral position switch assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0617 Starter Signal

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0617 Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more

WIRING DIAGRAM

A359761E03
0.604,0.354 0.917,0.552 0.313,0.198 10 false NE 0.438,0.708 0.917,0.906 0.479,0.198 10 false STAR 0.542,2.521 1.021,2.719 0.479,0.198 10 false STA 6.365,2.531 6.844,2.729 0.479,0.198 10 false STA 6.375,0.708 6.854,0.906 0.479,0.198 10 false NSW 6.375,0.365 6.854,0.563 0.479,0.198 10 false NEO 6.063,0.26 6.542,0.427 0.479,0.167 10 false 23 6.063,0.615 6.542,0.781 0.479,0.167 10 false 11 6.063,2.438 6.542,2.604 0.479,0.167 10 false 22 3.917,1.323 4.396,1.49 0.479,0.167 10 false C22 3.927,1.521 5.292,1.927 1.365,0.406 10 false Park/Neutral Position Switch Assembly 0.927,0.354 1.406,0.521 0.479,0.167 10 false G16 0.927,0.708 1.406,0.875 0.479,0.167 10 false G17 0.979,0.531 1.458,0.698 0.479,0.167 10 false 16 1.021,0.167 1.5,0.333 0.479,0.167 10 false 6 0.969,2.344 1.448,2.51 0.479,0.167 10 false 37 0.927,2.521 1.406,2.688 0.479,0.167 10 false G17 0.135,2.927 1.958,3.302 1.823,0.375 10 false Certification ECU (Smart Key ECU Assembly) 3.646,1.24 4.125,1.406 0.479,0.167 10 false B 3.646,1.917 4.125,2.083 0.479,0.167 10 false L 3.646,2.135 4.125,2.302 0.479,0.167 10 false 5 3.646,1.01 4.125,1.177 0.479,0.167 10 false 4 6.438,2.865 6.917,3.031 0.479,0.167 10 false G49 6.438,3.042 6.917,3.208 0.479,0.167 10 false ECM 1.385,4.656 2.5,4.865 1.115,0.208 10 false FL MAIN 3.0W 1.896,3.844 3.01,4.052 1.115,0.208 10 false ST NO. 1 3.813,4.125 4.927,4.333 1.115,0.208 10 false ST NO. 1 3.646,3.76 3.854,3.917 0.208,0.156 10 false 2 3.031,3.76 3.24,3.917 0.208,0.156 10 false 5 3.031,4.51 3.24,4.667 0.208,0.156 10 false 3 3.656,4.5 3.896,4.708 0.24,0.208 10 false 1 3.042,5.208 3.521,5.375 0.479,0.167 10 false C26 2.365,5.531 2.844,5.698 0.479,0.167 10 false D3 3.031,5.021 3.271,5.229 0.24,0.208 10 false 1 2.375,5.354 2.615,5.563 0.24,0.208 10 false 1 2.656,5.542 3.135,5.708 0.479,0.167 10 false B 2.552,6.156 3.75,6.344 1.198,0.188 10 false Starter Assembly 1.49,5.958 2.031,6.177 0.542,0.219 10 false Battery 3.073,5.406 3.552,5.573 0.479,0.167 10 false ST

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·


HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 234 118

d.

Read the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more.

Result:
Result Proceed to
Driving at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more OFF A
ON B




A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (park/neutral position switch assembly - ST NO. 1 relay - ECM - certification ECU (smart key ECU assembly)).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P0617 is output A
DTCs are not output B



A

5.CHECK SMART ENTRY AND START SYSTEM (START FUNCTION)

B

END

5.CHECK SMART ENTRY AND START SYSTEM (START FUNCTION)

Result:
Proceed to
OK
NG



OK

NG

REPAIR SMART ENTRY AND START SYSTEM