Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART)
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0245023 ECD SYSTEM(for i-ART) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P245C  Exhaust Gas Recirculation Cooler Bypass Control Circuit Low  P245D  Exhaust Gas Recirculation Cooler Bypass Control Circuit High  


DESCRIPTION

The vacuum switching valve assembly (for EGR bypass valve) is controlled by the ECM, and the opening and closing of the EGR cooler bypass valve is performed according to the vacuum applied by the vacuum pump.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P245C Exhaust Gas Recirculation Cooler Bypass Control Circuit Low Open or short in the vacuum switching valve assembly (for EGR bypass valve) for 3 seconds (1 trip detection logic).
·

Open or short in vacuum switching valve assembly (for EGR bypass valve) circuit

·

Vacuum switching valve assembly (for EGR bypass valve)

·

ECM


Comes on DTC stored
P245D Exhaust Gas Recirculation Cooler Bypass Control Circuit High Open or short in the vacuum switching valve assembly (for EGR bypass valve) for 3 seconds (1 trip detection logic).
·

Open or short in vacuum switching valve assembly (for EGR bypass valve) circuit

·

Vacuum switching valve assembly (for EGR bypass valve)

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P245C
P245D
Engine switch on (IG) for 3 seconds or more

WIRING DIAGRAM

A348547E09
3.146,1.042 3.604,1.24 0.458,0.198 10 false C42 3.073,1.229 5.344,1.635 2.271,0.406 10 false Vacuum Switching Valve Assembly (for EGR Bypass Valve) 5.979,0.458 6.438,0.656 0.458,0.198 10 false 16 6.271,0.646 6.813,0.854 0.542,0.208 10 false ECBV 5.938,0.656 6.396,0.854 0.458,0.198 10 false C38 6.271,4.229 6.813,4.438 0.542,0.208 10 false MREL 5.948,4.354 6.406,4.552 0.458,0.198 10 false G49 6,4.156 6.458,4.354 0.458,0.198 10 false 14 1.854,4.354 2.313,4.552 0.458,0.198 10 false 2K 5.115,2.813 5.573,3.01 0.458,0.198 10 false 2G 1.865,2.823 2.323,3.021 0.458,0.198 10 false 2B 1.865,3.219 2.323,3.417 0.458,0.198 10 false 2J 3.406,4.667 4.469,4.885 1.063,0.219 10 false EFI-MAIN NO. 1 2.479,5.01 4.615,5.24 2.135,0.229 10 false Instrument Panel Junction Block 0.594,5.667 1.365,5.865 0.771,0.198 10 false Battery 0.438,4.865 1.125,5.042 0.688,0.177 10 false FL MAIN 0.688,2.99 1.313,3.208 0.625,0.219 10 false J/B-B 0.698,2.688 0.885,2.885 0.188,0.198 10 false 1 0.969,2.688 1.188,2.896 0.219,0.208 10 false 2 2.281,4.156 3.344,4.375 1.063,0.219 10 false EFI-MAIN NO. 1 2.469,2.979 3.531,3.198 1.063,0.219 10 false EFI-MAIN NO. 2 3.396,3.531 4.458,3.75 1.063,0.219 10 false EFI-MAIN NO. 2 4.365,2.99 5.083,3.229 0.719,0.24 10 false EFI NO. 1 4.76,2.677 4.979,2.885 0.219,0.208 10 false 2 4.51,2.667 4.698,2.865 0.188,0.198 10 false 1 3.042,2.688 3.26,2.896 0.219,0.208 10 false 2 2.896,3.844 3.115,4.052 0.219,0.208 10 false 2 2.646,3.854 2.833,4.052 0.188,0.198 10 false 1 4.49,0.792 4.708,1 0.219,0.208 10 false 2 2.792,2.688 2.979,2.885 0.188,0.198 10 false 1 3.104,0.76 3.292,0.958 0.188,0.198 10 false 1 1.906,2.635 2.094,2.833 0.188,0.198 10 false 1 1.896,3.042 2.083,3.24 0.188,0.198 10 false 5 1.906,4.177 2.094,4.375 0.188,0.198 10 false 3 5.156,2.625 5.344,2.823 0.188,0.198 10 false 3 5.146,3.042 5.333,3.24 0.188,0.198 10 false 9 5.156,3.802 5.344,4 0.188,0.198 10 false 7 5.146,4.177 5.333,4.375 0.188,0.198 10 false 8 5.115,3.219 5.573,3.417 0.458,0.198 10 false 2P 5.104,3.99 5.563,4.188 0.458,0.198 10 false 2G 5.115,4.344 5.573,4.542 0.458,0.198 10 false 2P 6.438,5.656 6.979,5.865 0.542,0.208 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR BYPASS VALVE)
a.

Inspect the vacuum switching valve assembly (for EGR bypass valve).

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EGR BYPASS VALVE SWITCHING VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR BYPASS VALVE) (POWER SOURCE CIRCUIT)

NG

7.REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR BYPASS VALVE)
2.CHECK VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR BYPASS VALVE) (POWER SOURCE CIRCUIT)
a.

Disconnect the vacuum switching valve assembly (for EGR bypass valve) connector.


b.
A348992C05
1.469,1.042 1.875,1.365 0.406,0.323 0.177,0.125 0.49,0.323 0.313,0.198 10 false *a 1.542,1.125 1.906,1.344 0.365,0.219 10 false C42
*a Front view of wire harness connector
(to Vacuum Switching Valve Assembly (for EGR Bypass Valve))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C42-1 - Body ground Engine switch on (IG) 11 to 14 V



c.

Reconnect the vacuum switching valve assembly (for EGR bypass valve) connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) - ECM)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) - ECM)
a.

Disconnect the vacuum switching valve assembly (for EGR bypass valve) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C42-2 - C38-16 (ECBV) Always Below 1 Ω
C42-2 or C38-16 (ECBV) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the vacuum switching valve assembly (for EGR bypass valve) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.

HINT:

If the voltage at the vacuum switching valve assembly (for EGR bypass valve) connector is not 11 to 14 V, repair or replace the harness and connector between the vacuum switching valve assembly (for EGR bypass valve) and instrument panel junction block.



Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the engine switch on (IG) for 3 seconds.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

7.REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR BYPASS VALVE)
a.

Replace the vacuum switching valve assembly (for EGR bypass valve).

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EGR BYPASS VALVE SWITCHING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED