Home › Engine / Hybrid System › 2TR-FBE INTAKE / EXHAUST › INTAKE MANIFOLD › from 2016.07
RM33K0E _51 Engine / Hybrid System _054516 2TR-FBE INTAKE / EXHAUST _0267063 INTAKE MANIFOLD A

2TR-FBE INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17111 1.INSTALL INTAKE MANIFOLD

a.
A341602

Install the intake manifold insulator to the intake manifold.

HINT:

Insert the protrusions of the intake manifold insulator into the grille of the intake manifold.


NOTICE:
A341603

Insert the intake manifold insulator until the protrusion of the line as shown in the illustration.



b.
A385855N01
0.385,1.875 0.542,2.073 0.156,0.198 10 false A 0.823,1.01 0.979,1.208 0.156,0.198 10 true A 1.615,0.052 1.771,0.25 0.156,0.198 10 true B

Install the 3 wire harness clamp brackets to the intake manifold with the 3 bolts.

Torque:
for bolt A : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for bolt B : 10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Install a new gasket to the intake manifold.


d.
A384247C01
1.875,0.052 2.042,0.24 0.167,0.188 10 true 1 2.865,1.01 3.021,1.208 0.156,0.198 10 true 2 0.427,1.052 0.583,1.25 0.156,0.198 10 true 3 3.208,0.792 3.365,0.99 0.156,0.198 10 true 4 0.115,0.813 0.271,1.01 0.156,0.198 10 true 5 1.896,1.948 2.052,2.146 0.156,0.198 10 true 6 1.385,1.948 1.542,2.146 0.156,0.198 10 true 7
V100135

Bolt
V100136

Nut


Temporarily install the intake manifold with the 5 bolts and 2 nuts, and then tighten the bolts and nuts in the sequence shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


e.

Install the 2 No. 2 intake manifold insulators to the intake manifold.


f.
A384243

Install the purge line hose to the intake manifold, and slide the clip to secure the hose.


g.

Connect the union to connector tube hose to the intake manifold, and slide the clip to secure the hose.


h.

Connect the No. 3 PCV hose to the intake manifold, and slide the clip to secure the hose.


i.

Attach the No. 2 water by-pass hose to the intake manifold.


j.
A383810

Connect the heater water pipe sub-assembly to the intake manifold with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


k.

Attach the wire harness clamp and connect the No. 2 glow plug connector to the intake manifold.


l.

Attach the 2 wire harness clamps and connect the No. 1 glow plug connector to the intake manifold.


m.

Attach the No. 1 fuel hose to the intake manifold.


n.

Attach the 3 wire harness clamps to the wire harness clamp bracket.


Hide 22030 4.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY