Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2016.07
RM33K0E _54 Brake _043533 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0222679 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display the DTC by blinking the ABS warning light.

WIRING DIAGRAM

C332427E07
5.573,1.969 7.115,2.344 1.542,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 5.313,1.969 5.677,2.24 0.365,0.271 10 false A3 0.604,3.417 1.083,3.667 0.479,0.25 10 false ECM 0.51,4.313 2.344,4.542 1.833,0.229 10 false : CAN Communication Line 3.542,3.375 4.021,3.625 0.479,0.25 10 false DLC3 5.979,0.688 6.458,0.938 0.479,0.25 10 false CANH 5.688,0.51 6.052,0.781 0.365,0.271 10 false 25 5.958,1.406 6.438,1.656 0.479,0.25 10 false CANL 5.698,1.198 6.063,1.469 0.365,0.271 10 false 14 0.865,0.708 1.344,0.958 0.479,0.25 10 false CANH 0.896,1.427 1.375,1.677 0.479,0.25 10 false CANL 1.406,0.708 1.771,0.979 0.365,0.271 10 false G56 1.406,1.406 1.771,1.677 0.365,0.271 10 false G56 1.802,0.698 2.167,0.969 0.365,0.271 10 false G49 1.802,1.406 2.167,1.677 0.365,0.271 10 false G49 2.188,0.698 2.552,0.969 0.365,0.271 10 false G129 2.188,1.406 2.552,1.677 0.365,0.271 10 false G129 2.583,0.698 2.948,0.969 0.365,0.271 10 false G159 2.583,1.417 2.948,1.688 0.365,0.271 10 false G159 1.427,0.469 1.792,0.74 0.365,0.271 10 false 13*1 1.823,0.458 2.188,0.729 0.365,0.271 10 false 17*2 2.24,0.448 2.604,0.719 0.365,0.271 10 false 24*3 2.646,0.458 3.01,0.729 0.365,0.271 10 false 31*4 1.438,1.156 1.802,1.427 0.365,0.271 10 false 14*1 1.844,1.156 2.208,1.427 0.365,0.271 10 false 28*2 2.25,1.146 2.615,1.417 0.365,0.271 10 false 23*3 2.656,1.167 3.021,1.438 0.365,0.271 10 false 25*4 3.302,3.375 3.667,3.646 0.365,0.271 10 false G7 3.406,2.792 3.885,3.042 0.479,0.25 10 false CG 3.188,2.615 3.552,2.885 0.365,0.271 10 false 4 3.417,2.167 3.896,2.417 0.479,0.25 10 false TC 3.135,2.01 3.5,2.281 0.365,0.271 10 false 13 1.094,2.167 1.573,2.417 0.479,0.25 10 false TC 1.406,2.167 1.885,2.417 0.479,0.25 10 false G57 1.427,1.906 1.792,2.177 0.365,0.271 10 false 19*1 1.802,2.167 2.167,2.438 0.365,0.271 10 false G49 1.823,1.906 2.188,2.177 0.365,0.271 10 false 25*2 2.198,2.167 2.563,2.438 0.365,0.271 10 false G130 2.229,1.917 2.594,2.188 0.365,0.271 10 false 11*3 2.594,2.167 2.958,2.438 0.365,0.271 10 false G158 2.688,1.927 3.052,2.198 0.365,0.271 10 false 6*4 4.76,3.031 6.719,3.344 1.958,0.313 10 false *1: for 2TR-FE and 2TR-FBE 4.75,3.469 6.833,3.76 2.083,0.292 10 false *2: for 1GD-FTV 4.771,3.948 6.854,4.24 2.083,0.292 10 false *3: for 1KD-FTV 4.792,4.375 6.875,4.667 2.083,0.292 10 false *4: for 1GR-FE

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.INSPECT DLC3

DTC is output

2.INSPECT DLC3
a.
C269109C60
0.115,1.49 0.479,1.719 0.365,0.229 1.635,1.813 1.823,1.49 true 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 1.521,1.844 1.833,2.042 0.313,0.198 10 false TC 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.198,1.521 0.51,1.719 0.313,0.198 10 false G7
*a Front view of DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G7-13 (TC) - G7-4 (CG) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.REPLACE ECM

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
3.REPLACE ECM
a.
C269109C60
0.115,1.49 0.479,1.719 0.365,0.229 1.635,1.813 1.823,1.49 true 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 1.521,1.844 1.833,2.042 0.313,0.198 10 false TC 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.198,1.521 0.51,1.719 0.313,0.198 10 false G7
*a Front view of DLC3


Turn the ignition switch off.



c.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

d.

Check that the ABS warning light are blinking.

OK:

The ABS warning light are blinking.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the G57*1, G49*2, G130*3 or G158*4 ECM connector.

*1: for 2TR-FE and 2TR-FBE

*2: for 1GD-FTV

*3: for 1KD-FTV

*4: for 1GR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE and 2TR-FBE:
Tester Connection Condition Specified Condition
G7-13 (TC) - G57-19 (TC) Always Below 1 Ω
G7-13 (TC) or G57-19 (TC) - Body ground Always 10 kΩ or higher

for 1GD-FTV:
Tester Connection Condition Specified Condition
G7-13 (TC) - G49-25 (TC) Always Below 1 Ω
G7-13 (TC) or G49-25 (TC) - Body ground Always 10 kΩ or higher

for 1KD-FTV:
Tester Connection Condition Specified Condition
G7-13 (TC) - G130-11 (TC) Always Below 1 Ω
G7-13 (TC) or G130-11 (TC) - Body ground Always 10 kΩ or higher

for 1GR-FE:
Tester Connection Condition Specified Condition
G7-13 (TC) - G158-6 (TC) Always Below 1 Ω
G7-13 (TC) or G158-6 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C269109C61
0.115,1.49 0.479,1.719 0.365,0.229 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.208,1.521 0.521,1.719 0.313,0.198 10 false G7
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE ECM
a.
C269109C60
0.115,1.49 0.479,1.719 0.365,0.229 1.635,1.813 1.823,1.49 true 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 1.521,1.844 1.833,2.042 0.313,0.198 10 false TC 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.198,1.521 0.51,1.719 0.313,0.198 10 false G7
*a Front view of DLC3


Replace the ECM.

for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL

for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>ECM>REMOVAL

for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL

for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ECM>REMOVAL

for 2TR-FBE: Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>ECM>REMOVAL


b.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

c.

Check that the ABS warning light are blinking.

OK:

The ABS warning light are blinking.



Result:
Proceed to
OK
NG



OK

END

NG