Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2016.07
RM33K0E _54 Brake _043533 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0222679 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

The brake fluid level is insufficient.

·

EBD operation is not possible.

·

The vacuum inside the brake booster decreases.*

*: for 1GD-FTV and 1KD-FTV



WIRING DIAGRAM

C325986E12
0.531,5.375 2.656,5.635 2.125,0.26 10 false : CAN Communication Line 2.729,1.74 3.729,1.906 1,0.167 10 false from IG Circuit 6.229,1.75 6.479,2 0.25,0.25 10 false IG1 5.927,1.573 6.177,1.823 0.25,0.25 10 false 34 5.99,2.583 6.24,2.833 0.25,0.25 10 false 1 6.25,2.74 6.667,3.073 0.417,0.333 10 false GND1 5.552,3.729 5.802,3.979 0.25,0.25 10 false A3 5.552,3.927 7.135,4.344 1.583,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 6.24,0.365 6.656,0.698 0.417,0.333 10 false CANH 6.25,0.813 6.667,1.146 0.417,0.333 10 false CANL 2.729,0.781 3.146,1.115 0.417,0.333 10 false CANL 2.688,0.365 3.104,0.698 0.417,0.333 10 false CANH 5.938,0.188 6.188,0.438 0.25,0.25 10 false 25 5.938,0.625 6.188,0.875 0.25,0.25 10 false 14 3.24,0.615 3.49,0.865 0.25,0.25 10 false 35 3.229,0.177 3.479,0.427 0.25,0.25 10 false 36 1.865,0.354 2.281,0.688 0.417,0.333 10 false SW 1.563,0.198 1.813,0.448 0.25,0.25 10 false 16 1.854,0.802 2.417,1.156 0.563,0.354 10 false VCM* 1.646,0.656 1.896,0.906 0.25,0.25 10 false 9 1.281,1.177 1.698,1.51 0.417,0.333 10 false G8 1.552,1.167 3.552,1.5 2,0.333 10 false Combination Meter Assembly 1.302,3.052 1.719,3.385 0.417,0.333 10 false A34 1.604,3.052 3.938,3.385 2.333,0.333 10 false Vacuum Warning Switch Assembly* 2.281,2.5 2.698,2.833 0.417,0.333 10 false 2 3.438,2.5 3.854,2.833 0.417,0.333 10 false 1 0.719,4.302 3.219,4.698 2.5,0.396 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly) 0.469,4.292 0.885,4.625 0.417,0.333 10 false A5 1.635,3.771 2.052,4.104 0.417,0.333 10 false + 2.292,3.771 2.708,4.104 0.417,0.333 10 false E 2.552,3.74 2.969,4.073 0.417,0.333 10 false 2 1.396,3.74 1.813,4.073 0.417,0.333 10 false 1 4.208,1.948 5.073,2.167 0.865,0.219 10 false IG1 NO. 3 4.656,4.76 6.865,5.115 2.208,0.354 10 false *: for 1GD-FTV and 1KD-FTV

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform Test Mode (Signal Check) to acquire the rear differential lock identification information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

DTC is output

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.INSPECT BATTERY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG




OK

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.
C260095C35
0.177,0.917 0.51,1.177 0.333,0.26 2.094,1.833 2.302,1.396 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.26,0.958 0.573,1.156 0.313,0.198 10 false A3 1.865,1.792 2.167,2 0.302,0.208 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A3 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A3-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.
C260095C36
0.219,0.927 0.563,1.156 0.344,0.229 1.115,0.833 1.26,0.146 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.302,0.958 0.615,1.156 0.313,0.198 10 false A3 1.292,0.063 1.906,0.26 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A3-1 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
a.
C235854C01
0.175,0.239 0.361,0.4 0.186,0.161 10 *a
*a Component without harness connected
(Brake Fluid Level Warning Switch [Brake Master Cylinder Reservoir Assembly])


Turn the ignition switch off.


b.

Remove the reservoir filler cap and strainer.


c.

Disconnect the A5 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch off (Float up) 10 kΩ or higher
Switch on (Float down) Below 1 Ω


HINT:

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Disconnect the G8 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-16 (SW) - A5-1 (+) Always Below 1 Ω
A5-2 (E) - Body ground Always Below 1 Ω
G8-16 (SW) or A5-1 (+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (for 1GD-FTV and 1KD-FTV)
OK (for 1GR-FE, 2TR-FE and 2TR-FBE)
NG



OK (for 1GD-FTV and 1KD-FTV)

8.INSPECT VACUUM WARNING SWITCH ASSEMBLY

OK (for 1GR-FE, 2TR-FE and 2TR-FBE)

10.READ VALUE USING GTS (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT VACUUM WARNING SWITCH ASSEMBLY
a.

Remove the vacuum warning switch assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM WARNING SWITCH(for Diesel)>REMOVAL


b.

Inspect the vacuum warning switch assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM WARNING SWITCH(for Diesel)>ON-VEHICLE INSPECTION

OK:

The vacuum warning switch assembly is normal.



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)

NG

REPLACE VACUUM WARNING SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)
a.

Disconnect the A34 vacuum warning switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-9 (VCM) - A34-2 Always Below 1 Ω
A34-1 - Body ground Always Below 1 Ω
G8-9 (VCM) or A34-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.READ VALUE USING GTS (BRAKE WARNING LIGHT)
a.

Reinstall the reservoir filler cap and strainer.


b.

for 1GD-FTV and 1KD-FTV:

Reinstall the vacuum warning switch assembly.


c.

Reconnect the A3 skid control ECU (brake actuator assembly) connector, G8 combination meter assembly connector and the A5 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


d.

for 1GD-FTV and 1KD-FTV:

Reconnect the A34 vacuum warning switch assembly connector.


e.

Connect the GTS to the DLC3.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


i.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light OFF or ON OFF: Warning light off
ON: Warning light on
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Brake Warning Light
50003 105 52
j.

Check the GTS display condition of the brake warning light.


Result:
Proceed to
Display of the Data List remains OFF
Display of the Data List remains ON



Display of the Data List remains OFF

Display of the Data List remains ON