Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › from 2016.10
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0245023 ECD SYSTEM(for i-ART) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P0545  Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 1)  P0546  Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 1)  


DESCRIPTION

A390293E01
5.563,4.625 5.74,4.625 5.74,4.625 5.875,4.771 true 2.813,2.469 3.167,3.042 3.167,3.042 3.354,3.042 true 2.813,1.542 3.24,0.958 3.24,0.958 3.427,0.958 true 1.74,5.552 1.927,5.396 1.927,5.396 2.042,5.396 true 1.938,1.885 1.74,1.885 1.74,1.885 1.396,2.323 true 3.479,0.875 6.073,1.115 2.594,0.24 10 false Exhaust Gas Temperature Sensor 3.406,2.969 6,3.208 2.594,0.24 10 false No. 2 Exhaust Gas Temperature Sensor 4.958,1.896 5.417,2.094 0.458,0.198 10 false ECM 1.979,0.375 2.885,0.573 0.906,0.198 10 false Exhaust Gas 0.531,2.385 1.771,2.635 1.24,0.25 10 false DOC Catalyst 0.583,3.458 3.177,3.698 2.594,0.24 10 false Property of Output Voltage: 0.375,3.927 2.969,4.167 2.594,0.24 10 false Exhaust Gas Temperature (°C) 2.188,6.417 5.094,6.646 2.906,0.229 10 false Exhaust Gas Temperature Sensor Voltage (V) 2.083,5.313 3.604,5.49 1.521,0.177 10 false Stores P0545 or P2032 4.115,4.552 5.646,4.781 1.531,0.229 10 false Stores P0546 or P2033 1.208,4.271 1.573,4.469 0.365,0.198 10 false 1000 1.281,4.438 1.646,4.635 0.365,0.198 10 false 960 1.281,4.646 1.646,4.844 0.365,0.198 10 false 760 1.281,4.875 1.646,5.073 0.365,0.198 10 false 560 1.281,5.104 1.646,5.302 0.365,0.198 10 false 360 1.281,5.333 1.646,5.531 0.365,0.198 10 false 160 1.313,5.615 1.677,5.813 0.365,0.198 10 false -40 1.604,5.802 1.823,6.031 0.219,0.229 10 false 0 1.708,5.802 1.927,6.031 0.219,0.229 10 false 0.2 1.979,5.802 2.198,6.031 0.219,0.229 10 false 0.5 2.417,5.802 2.635,6.031 0.219,0.229 10 false 1.0 2.844,5.802 3.063,6.031 0.219,0.229 10 false 1.5 3.281,5.802 3.5,6.031 0.219,0.229 10 false 2.0 3.708,5.802 3.927,6.031 0.219,0.229 10 false 2.5 4.146,5.802 4.365,6.031 0.219,0.229 10 false 3.0 5.021,5.802 5.26,6.031 0.24,0.229 10 false 4.0 4.583,5.802 4.896,6.031 0.313,0.229 10 false 3.5 5.438,5.802 5.656,6.031 0.219,0.229 10 false 4.5 5.698,5.802 6.042,6.031 0.344,0.229 10 false 4.95 6.01,5.802 6.448,6.031 0.438,0.229 10 false 5.0

The exhaust gas temperature sensors are installed before and after the DOC catalyst to sense the exhaust gas temperature.

A thermistor built into the sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature, the higher the thermistor resistance value. The higher the exhaust gas temperature, the lower the thermistor resistance value.

The exhaust gas temperature sensor is powered by a 5 V supply from the THTO and THCO terminals of the ECM, via resistor R.

Resistor R and the exhaust gas temperature sensor are connected in series. When the resistance value of the exhaust gas temperature sensor changes in accordance with the exhaust gas temperature, the voltage at terminals THTO and THCO also changes. The exhaust gas temperature sensor monitors the temperature upstream of the DOC catalyst. The No. 2 exhaust gas temperature sensor monitors the temperature downstream of the DOC catalyst.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0545 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 1) Exhaust gas temperature sensor output voltage is below 0.2 V for 3 seconds or more when all conditions are met (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or higher


·

Open or short in exhaust gas temperature sensor circuit

·

Exhaust gas temperature sensor

·

ECM


Comes on DTC stored
P0546 Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 1) Exhaust gas temperature sensor output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or higher


·

Open or short in exhaust gas temperature sensor circuit

·

Exhaust gas temperature sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0545
P0546
Exhaust Temperature B1S1

HINT:
·

Sensor 1 represents the sensor located upstream of the DOC catalyst.

·

When DTC P0545 and P0546 is output, check the exhaust gas temperature indicated by "Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S1" using the GTS.


Reference:
Condition Exhaust Temperature B1S1 Exhaust Gas Temperature Sensor Condition
Idling with warm engine Constant at between 50 and 700°C (122 and 1292°F) Normal
0°C (32°F) Open circuit
1000°C (1832°F) Short circuit


MONITOR DESCRIPTION

The ECM constantly monitors the output voltages from the exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.2 V and 4.95 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0545
P0546
Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.

WIRING DIAGRAM

A388908E02
1.99,1.313 4.135,1.521 2.146,0.208 10 false Exhaust Gas Temperature Sensor 1.979,1.135 2.594,1.333 0.615,0.198 10 false C111 2.01,3.708 4.865,3.948 2.854,0.24 10 false No. 2 Exhaust Gas Temperature Sensor 2.01,3.552 2.625,3.75 0.615,0.198 10 false C139 2.156,0.865 2.313,1.063 0.156,0.198 10 false 1 2.188,3.188 2.344,3.385 0.156,0.198 10 false 1 3.74,0.875 3.896,1.073 0.156,0.198 10 false 2 3.74,3.198 3.896,3.396 0.156,0.198 10 false 2 5.76,0.75 6.375,0.948 0.615,0.198 10 false THTO 5.75,1.698 6.365,1.896 0.615,0.198 10 false ETTO 5.76,3.083 6.375,3.281 0.615,0.198 10 false THCO 5.771,4.031 6.385,4.229 0.615,0.198 10 false ETCO 6.021,5.031 6.635,5.229 0.615,0.198 10 false C38 6.042,5.219 6.656,5.417 0.615,0.198 10 false ECM 3.313,0.854 3.927,1.052 0.615,0.198 10 false THC3 2.375,3.208 2.99,3.406 0.615,0.198 10 false E2 2.385,0.875 3,1.073 0.615,0.198 10 false E2 3.281,3.198 3.896,3.396 0.615,0.198 10 false THCO 5.427,0.865 5.74,1.104 0.313,0.24 10 false 23 5.438,1.833 5.75,2.073 0.313,0.24 10 false 22 5.448,3.208 5.76,3.448 0.313,0.24 10 false 33 5.458,4.156 5.771,4.396 0.313,0.24 10 false 26

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (EXHAUST TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S1.


d.

Read the value.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S1
50003 234 858
Standard:

Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling with warm engine), and varies after an engine speed of 3000 rpm is maintained for 1 minute.


Result:
Temperature Displayed Proceed to
0°C (32°F) (After warming up the engine) A
1000°C (1832°F) or higher B
Same as the actual exhaust gas temperature C


HINT:
·

If there is a short circuit, the GTS will indicate 0°C (32°F).

·

If there is an open circuit, the GTS will indicate 1000°C (1832°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A356525C12
1.479,2.719 1.927,3.052 0.448,0.333 1.406,4.052 1.615,3.583 true 2.031,4.042 1.813,3.583 true 0.563,2.76 0.875,2.958 0.313,0.198 10 false *a 0.688,1.802 1,2 0.313,0.198 10 false *1 2.583,1.771 2.896,1.969 0.313,0.198 10 false *2 1.542,2.813 1.99,3.031 0.448,0.219 10 false C111 1.292,4.083 1.74,4.281 0.448,0.198 10 false E2 2,4.083 2.417,4.271 0.417,0.188 10 false THC3 1.531,0.656 1.948,0.844 0.417,0.188 10 false THC3 1.625,1.354 2.073,1.552 0.448,0.198 10 false E2
*1 Exhaust Gas Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Exhaust Gas Temperature Sensor)


Disconnect the exhaust gas temperature sensor connector.


b.

Connect terminals 1 (E2) and 2 (THC3) of the exhaust gas temperature sensor connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S1.


f.

Read the value.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S1
50003 234 858
Standard:

1000°C (1832°F)



Result:
Proceed to
OK
NG



OK

3.REPLACE EXHAUST GAS TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
3.REPLACE EXHAUST GAS TEMPERATURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the exhaust gas temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C111-2 (THC3) - C38-23 (THTO) Always Below 1 Ω
C111-1 (E2) - C38-22 (ETTO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A178587C05
0.792,1.594 1.104,1.792 0.313,0.198 10 false *1 2.698,1.677 3.01,1.875 0.313,0.198 10 false *2
*1 Exhaust Gas Temperature Sensor
*2 ECM


Disconnect the exhaust gas temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Exhaust Temperature B1S1.


e.

Read the value.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S1
50003 234 858
Standard:

0°C (32°F)



Result:
Proceed to
OK
NG



OK

7.REPLACE EXHAUST GAS TEMPERATURE SENSOR

NG

8.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
7.REPLACE EXHAUST GAS TEMPERATURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the exhaust gas temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C111-2 (THC3) or C38-23 (THTO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Turn the engine switch off and wait for at least 30 seconds


e.

Start the engine and turn the GTS on.


f.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END