Home › Engine / Hybrid System › 1GR-FE COOLING › RADIATOR › 2015.06–2016.01
RM3250E _51 Engine / Hybrid System _037986 1GR-FE COOLING _0177672 RADIATOR A

1GR-FE COOLING  RADIATOR  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
A343701

Do not remove the radiator cap sub-assembly, cylinder block drain cock plugs or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


PROCEDURE

Hide 51410 2.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (for 4WD)

Hide 16593 4.REMOVE NO. 1 RADIATOR AIR GUIDE

a.
A344519

Remove the 4 clips and radiator air guide.

NOTICE:

Do not reuse the clip.



Hide 16571 5.REMOVE RADIATOR HOSE INLET

a.
A344512

Slide the 2 hose clamps and remove the radiator hose inlet from the radiator assembly and water inlet assembly.


Hide 16572 6.REMOVE RADIATOR HOSE OUTLET

a.
A344513C01
0.51,0.177 0.76,0.375 0.25,0.198 10 false *a 0.521,1.156 0.75,1.365 0.229,0.208 10 false *a
*a Push


Detach the clamp from the radiator hose outlet.


b.

Slide the 2 hose clamps and remove the radiator hose outlet from the radiator assembly and water inlet assembly.


Hide 32941 7.DISCONNECT NO. 1 OIL COOLER INLET HOSE

a.
A350027

Slide the hose clamp and disconnect the No. 1 oil cooler inlet hose from the radiator assembly.


Hide 32942 8.DISCONNECT NO. 1 OIL COOLER OUTLET HOSE

a.
A350028

Slide the hose clamp and disconnect the No. 1 oil cooler outlet hose from the radiator assembly.


Hide 16470 9.REMOVE RADIATOR RESERVOIR

a.

Disconnect the reservoir hose from the radiator assembly.


b.

Remove the 2 bolts, radiator reservoir and grommet.


Hide 16711 10.REMOVE FAN SHROUD

a.
A344515

Remove the 3 bolts and disconnect the vane pump oil reservoir assembly from the radiator assembly and fan shroud.


b.
A344517

Detach the 6 clamps and disconnect the wire harness from the radiator assembly and fan shroud.


c.

Loosen the 4 nuts holding the fluid coupling fan.


d.

Remove the fan and generator V belt.

Click hereEngine / Hybrid System>1GR-FE ENGINE MECHANICAL>DRIVE BELT>REMOVAL


e.
A355207

Detach the 2 claws holding the fan shroud.


f.

Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the fluid coupling fan.

NOTICE:

Be careful not to damage the radiator core.



g.

Remove the fan pulley from the engine water pump assembly.


h.

Remove the clamp from the fan shroud.


Hide 16400 11.REMOVE RADIATOR ASSEMBLY

a.
A344518

Remove the 4 bolts.


b.
A346167

Slide the radiator assembly with cooler condenser assembly to the engine side.


c.
A341292

Detach the 2 claws and 2 guides to disconnect the cooler condenser assembly from radiator assembly.

NOTICE:
·

Do not allow the radiator assembly to interfere with other parts.

·

Do not apply any excessive force to the cooler condenser assembly and cooler pipe.




d.
A344520

Remove the radiator assembly from the vehicle.

NOTICE:

Do not apply excessive force to the cooler condenser assembly or cooler pipe when removing the radiator assembly.



Hide 16400B 12.REMOVE RADIATOR DRAIN COCK PLUG

a.

Remove the radiator drain cock plug from the radiator assembly.


b.

Remove the O-ring from the radiator drain cock plug.