Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2015.06–2016.08
RM3250E _56 Audio / Visual / Telematics _038052 AUDIO / VIDEO _0182296 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Telephone microphone signal is lost
·

Radio and display receiver assembly

·

Map light assembly

·

Telephone microphone assembly

·

Harness or connector



WIRING DIAGRAM

E322192E01
0.76,0.698 1.5,1.302 0.74,0.604 10 false Telephone Microphone Assembly 2,0.708 2.74,1.313 0.74,0.604 10 false MCO+ 2.031,1.188 2.771,1.792 0.74,0.604 10 false MCO- 1.979,1.667 2.719,2.271 0.74,0.604 10 false MACC 2.51,1.667 3.25,2.271 0.74,0.604 10 false 15 2.51,1.188 3.25,1.792 0.74,0.604 10 false 13 2.51,0.719 3.25,1.323 0.74,0.604 10 false 14 5.406,2.104 6.146,2.708 0.74,0.604 10 false 18 5.406,1.177 6.146,1.781 0.74,0.604 10 false 19 5.469,0.708 6.208,1.313 0.74,0.604 10 false 5 5.688,0.792 6.427,1.396 0.74,0.604 10 false MIN+ 5.677,1.26 6.417,1.865 0.74,0.604 10 false MIN- 5.677,1.74 6.417,2.344 0.74,0.604 10 false MACC 5.49,1.667 6.229,2.271 0.74,0.604 10 false 4 5.677,2.219 6.417,2.823 0.74,0.604 10 false SNS2 5.625,2.865 6.813,3.344 1.188,0.479 10 false G37 5.625,3.021 6.813,3.5 1.188,0.479 10 false Radio and Display Receiver Assembly 0.688,2.875 2.26,3.375 1.573,0.5 10 false Q3 0.688,3.052 2.26,3.552 1.573,0.5 10 false Map Light Assembly 3.417,2.396 4.99,2.896 1.573,0.5 10 false * 4.615,2.385 6.188,2.885 1.573,0.5 10 false * 0.323,3.458 1.927,3.76 1.604,0.302 10 false *: Shielded

CAUTION / NOTICE / HINT

HINT:

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G37 radio and display receiver assembly connector.


b.

Disconnect the Q3 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-4 (MACC) - Q3-15 (MACC) Always Below 1 Ω
G37-5 (MIN+) - Q3-14 (MCO+) Always Below 1 Ω
G37-19 (MIN-) - Q3-13 (MCO-) Always Below 1 Ω
G37-18 (SGND) - Body ground Always 10 kΩ or higher
G37-4 (MACC) or Q3-15 (MACC) - Body ground Always 10 kΩ or higher
G37-5 (MIN+) or Q3-14 (MCO+) - Body ground Always 10 kΩ or higher
G37-19 (MIN-) or Q3-13 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Inspect the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E316674C06
1.49,0.667 1.958,0.917 0.469,0.25 2.604,2.51 2.427,2.51 2.427,2.51 2.063,1.979 true 2.802,1.01 2.625,1.01 2.625,1.01 2.208,1.75 true 0.135,0.177 0.448,0.333 0.313,0.156 10 false *a 1.594,0.719 2.24,0.865 0.646,0.146 10 false G37 2.885,0.896 3.417,1.135 0.531,0.24 10 false MACC 2.667,2.375 3.198,2.615 0.531,0.24 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly with the connector still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-19 (MIN-) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G37-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



Result:
Proceed to
OK
NG



OK

4.CHECK MAP LIGHT ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.CHECK MAP LIGHT ASSEMBLY
a.
E316675C02
0.26,0.729 0.708,1 0.448,0.271 0.615,1.729 0.813,1.729 0.813,1.729 1.438,1.219 true 2.604,1.917 2.354,1.917 2.354,1.917 1.594,1.208 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.396,0.792 0.708,0.99 0.313,0.198 10 false Q3 2.677,1.781 3.25,2 0.573,0.219 10 false MCO- 0.177,1.594 0.75,1.813 0.573,0.219 10 false MCO+
*a Component with harness connected
(Map Light Assembly)


Reconnect the map light assembly with the connector still connected.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Turn the ignition switch to ACC.


c.

Connect an oscilloscope to terminals Q3-14 (MCO+) and Q3-13 (MCO-) of the map light assembly connector.


d.

Check the waveform of the telephone microphone assembly using the oscilloscope.


Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly is not output. A
A waveform synchronized with the voice input to the map light assembly is output. B



A

REPLACE TELEPHONE MICROPHONE ASSEMBLY

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY