Home › Engine / Hybrid System › 1TR-FE ENGINE MECHANICAL › CAMSHAFT
RM3250E _51 Engine / Hybrid System _037998 1TR-FE ENGINE MECHANICAL _0184010 CAMSHAFT A

1TR-FE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


PROCEDURE

Hide 13070A 1.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A344602C01
0.688,0.583 0.865,0.583 0.865,0.583 0.969,1.292 true 2.292,1.146 2.385,1.146 2.385,1.146 2.74,0.948 true 0.354,0.5 0.698,0.688 0.344,0.188 10 false SST 2.094,1.042 2.281,1.25 0.188,0.208 10 false *a
*a Hexagonal Portion


Using SST, grip the hexagonal portion, and then secure SST and No. 2 camshaft in a vise as shown in the illustration.

SST
09212-31010  

NOTICE:
·

Do not damage the No. 2 camshaft.

·

Never grip areas other than the hexagonal portion, as this may cause damage.




b.
A336440C01
0.854,1.229 1.49,0.469 1.49,0.469 1.677,0.469 true 1.896,1.458 2.125,1.823 2.125,1.823 2.333,1.823 false 1.698,0.365 1.896,0.563 0.198,0.198 10 false *a 2.365,1.729 2.563,1.938 0.198,0.208 10 false *b
*a Straight Pin Hole
*b Straight Pin


Align and attach the straight pin of the No. 2 camshaft with the straight pin hole of the camshaft timing exhaust gear assembly.


c.
A336442C01
0.531,1.042 0.844,1.042 false 1.354,0.813 1.646,0.542 1.646,0.542 1.833,0.542 false 0.333,0.948 0.531,1.135 0.198,0.188 10 false *1 0.063,0.042 0.26,0.24 0.198,0.198 10 false *a 0.052,1.865 0.24,2.052 0.188,0.188 10 false *b 1.552,0.198 1.74,0.385 0.188,0.188 10 false *c 1.854,0.448 2.052,0.635 0.198,0.188 10 false *d 1.51,1.948 1.708,2.146 0.198,0.198 10 false *e
*1 Camshaft Timing Exhaust Gear Assembly
*a INCORRECT
*b CORRECT
*c Clearance
*d Camshaft Flange
*e No Clearance


Check that there is no clearance between the camshaft timing exhaust gear assembly and camshaft flange.

NOTICE:
·

Since the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head receiving the shaft thrust may crack or be damaged, causing the camshaft to seize or break.

·

Be sure not to remove the other 4 bolts. If removing the bolts, exchange the camshaft timing exhaust gear assembly.




d.

Fix the camshaft timing exhaust gear assembly with the flange bolt.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)


Hide 13050 2.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A344602C01
0.688,0.583 0.865,0.583 0.865,0.583 0.969,1.292 true 2.292,1.146 2.385,1.146 2.385,1.146 2.74,0.948 true 0.354,0.5 0.698,0.688 0.344,0.188 10 false SST 2.094,1.042 2.281,1.25 0.188,0.208 10 false *a
*a Hexagonal Portion


Using SST, grip the hexagonal portion, and then secure SST and camshaft in a vise as shown in the illustration.

SST
09212-31010  

NOTICE:
·

Do not damage the camshaft.

·

Never grip areas other than the hexagonal portion, as this may cause damage.




b.
A336438C01
0.854,1.219 1.365,0.448 1.365,0.448 1.552,0.448 true 1.896,1.458 2.177,1.854 2.177,1.854 2.365,1.854 false 2.385,1.75 2.573,1.969 0.188,0.219 10 false *a 1.594,0.344 1.781,0.563 0.188,0.219 10 false *b
*a Straight Pin
*b Straight Pin Hole


Align the straight pin hole and straight pin and install the camshaft timing gear assembly to the camshaft.


c.

Lightly press the gear against the camshaft and turn the gear. Push further at the position where the straight pin enters the straight pin hole.

NOTICE:

Be sure not to turn the camshaft timing gear assembly in the retard direction (the right angle).



d.
A336441C01
0.865,0.865 0.573,0.865 false 1.313,0.823 1.49,0.594 1.49,0.594 1.792,0.594 false 0.375,0.771 0.688,0.927 0.313,0.156 10 false *1 0.052,0.042 0.24,0.25 0.188,0.208 10 false *a 0.063,1.958 0.271,2.156 0.208,0.198 10 false *b 1.531,0.25 1.74,0.448 0.208,0.198 10 false *c 1.823,0.49 2.01,0.677 0.188,0.188 10 false *d 1.5,2.031 1.698,2.24 0.198,0.208 10 false *e
*1 Camshaft Timing Gear Assembly
*a INCORRECT
*b CORRECT
*c Clearance
*d Camshaft Flange
*e No Clearance


Check that there is no clearance between the camshaft timing gear assembly and the flange of the camshaft.

NOTICE:
·

Since the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head receiving the shaft thrust may crack or be damaged, causing the camshaft to seize or break.

·

Be sure not to remove the other 3 bolts. If removing the bolts, exchange the camshaft timing gear assembly.




e.

With the camshaft timing gear assembly fixed in place, install the flange bolt.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)


f.

Check that the camshaft timing gear assembly can move in the retard direction (the right angle), and is locked at the most retarded position.


Hide 13511 3.INSTALL CAMSHAFT AND NO. 2 CAMSHAFT

HINT:

Perform "Inspection After Repairs" after replacing the camshaft or No. 2 camshaft.

Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A337710C01
2.021,0.885 2.115,0.885 2.115,0.885 2.406,1.042 true 2.448,0.917 2.74,0.917 true 2.76,0.813 2.979,1.021 0.219,0.208 10 true *a 1.833,0.802 2.031,1.021 0.198,0.219 10 true *b
*a Paint Mark
*b Timing Mark


Apply clean engine oil to the camshaft cams and cylinder head journals.


b.

Install the chain sub-assembly to the camshaft timing gear assembly with the paint mark of the link aligned with the timing mark of the camshaft timing gear assembly.


c.
A337711

Temporarily install the 4 No. 2 camshaft bearing caps using the 8 bolts as shown in the illustration.


d.

Install the chain sub-assembly to the No. 2 camshaft, and then install the No. 2 camshaft to the cylinder head sub-assembly.

HINT:

Place the chain sub-assembly on the camshaft timing gear assembly but do not engage the teeth of the sprocket and the chain sub-assembly.



e.

Move the camshaft in the direction shown in the illustration to loosen the chain sub-assembly, and align the paint mark on the camshaft timing gear assembly and chain sub-assembly and connect the chain sub-assembly to the camshaft timing gear assembly.

A337723C01
0.531,0.302 0.698,0.302 0.698,0.302 1.198,0.448 true 2.021,0.438 2.406,0.313 2.406,0.313 2.604,0.313 true 0.333,0.906 0.5,0.906 0.5,0.906 0.656,1.438 true 4.26,0.906 4.427,0.906 4.427,0.906 4.854,1.385 true 4.042,2.458 4.208,2.458 4.208,2.458 4.865,1.479 true 6.083,1.427 6.656,1.26 6.656,1.26 6.792,1.26 true 6.073,1.521 6.646,1.823 6.646,1.823 6.844,1.823 true 2.646,0.229 2.854,0.417 0.208,0.188 10 false *1 0.344,0.208 0.531,0.396 0.188,0.188 10 false *2 0.146,0.802 0.354,0.99 0.208,0.188 10 false *3 3.865,2.365 4.052,2.552 0.188,0.188 10 false *a 4.083,0.813 4.271,1.01 0.188,0.198 10 false *b 6.823,1.167 7.01,1.354 0.188,0.188 10 false *b 6.875,1.729 7.063,1.917 0.188,0.188 10 false *a
*1 Camshaft *2 No. 2 Camshaft
*3 Chain Sub-assembly - -
*a Timing Mark *b Paint Mark



f.
A336446C02
0.677,0.771 0.844,0.771 0.844,0.771 0.979,0.552 false 0.958,1.281 1.125,1.281 1.125,1.281 1.302,1.01 true 0.958,2.979 1.125,2.979 1.125,2.979 1.302,2.75 true 0.802,2.51 0.969,2.51 0.969,2.51 1.115,2.292 false 1.906,2.177 2.167,1.938 2.167,1.938 2.375,1.938 true 1.906,0.417 2.167,0.177 2.167,0.177 2.375,0.177 true 0.49,0.667 0.688,0.854 0.198,0.188 10 false *1 0.781,1.177 0.979,1.375 0.198,0.198 10 false *2 2.406,0.083 2.604,0.26 0.198,0.177 10 false *3 0.063,0.042 0.25,0.24 0.188,0.198 10 false *a 0.073,1.833 0.26,2.031 0.188,0.198 10 false *b 2.406,1.844 2.604,2.021 0.198,0.177 10 false *3 0.625,2.406 0.813,2.604 0.188,0.198 10 false *1 0.76,2.885 0.948,3.073 0.188,0.188 10 false *2
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap
*a INCORRECT
*b CORRECT


Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


g.
A337712

Temporarily install the No. 1 camshaft bearing cap and 4 No. 2 camshaft bearing caps using the 12 bolts.


h.
A337713N01
1.354,1.042 1.552,1.24 0.198,0.198 10 true 11 1.177,0.177 1.375,0.375 0.198,0.198 10 true 12 2.646,0.823 2.844,1.021 0.198,0.198 10 true 13 2.823,1.688 3.021,1.885 0.198,0.198 10 true 14 3.104,0.969 3.302,1.167 0.198,0.198 10 true 15 2.833,0.188 3.031,0.385 0.198,0.198 10 true 16 0.448,1.281 0.646,1.479 0.198,0.198 10 true 17 0.438,0.583 0.635,0.781 0.198,0.198 10 true 18 0.781,1.75 0.979,1.948 0.198,0.198 10 true 19 0.771,0.125 0.969,0.323 0.198,0.198 10 true 20 1.583,0.823 1.708,1.021 0.125,0.198 10 true 1 1.177,1.688 1.375,1.885 0.198,0.198 10 true 10 1.781,1.698 1.906,1.896 0.125,0.198 10 true 2 1.938,1.052 2.063,1.25 0.125,0.198 10 true 3 1.771,0.188 1.896,0.385 0.125,0.198 10 true 4 2.125,0.823 2.25,1.021 0.125,0.198 10 true 5 2.323,1.688 2.448,1.885 0.125,0.198 10 true 6 2.5,1.052 2.625,1.25 0.125,0.198 10 true 7 2.323,0.188 2.448,0.385 0.125,0.198 10 true 8 1.021,0.823 1.146,1.021 0.125,0.198 10 true 9

Tighten the 20 bolts in the order shown in the illustration.

Torque:
15.5 N*m (158 kgf*cm, 11 ft.*lbf)


Hide 13540 4.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A101303C25
1.854,1.531 2.104,1.708 2.104,1.708 2.24,1.708 true 2.323,0.781 2.552,0.344 2.552,0.344 2.677,0.344 true 0.563,1.854 0.563,1.521 false 2.26,1.615 2.49,1.792 0.229,0.177 10 false *b 0.5,1.875 0.698,2.063 0.198,0.188 10 false *c 2.729,0.25 2.917,0.458 0.188,0.208 10 false *a
*a Plunger
*b Stopper Plate
*c Hexagon Wrench


Move the stopper plate upward to release the lock and push the plunger deep into the tensioner.


b.

Move the stopper plate downward to set the lock and insert a hexagon wrench into the hole of the stopper plate.


c.

Install a new gasket and the No. 1 chain tensioner assembly with the bolt and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Remove the hexagon wrench after installing the timing chain guide.



d.

Install a new gasket to the timing chain cover plate.


e.

Install the timing chain cover plate to the timing chain cover sub-assembly with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 13566B 5.INSTALL TIMING CHAIN GUIDE

Hide 6.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A337700C02
2.698,1.031 2.031,1.188 2.031,1.188 2.698,0.771 true 1.125,0.635 1.396,1.344 1.396,1.344 1.01,0.854 true 0.865,2.396 0.635,2.104 0.635,2.104 0.448,2.104 true 2.458,2.427 2.729,2.104 2.729,2.104 2.854,2.104 true 2.615,3.792 2.365,3.792 2.365,3.792 1.823,4.219 true 1.854,1.083 2.042,1.271 0.188,0.188 10 true *a 2.646,3.698 2.844,3.885 0.198,0.188 10 true *b 1.063,0.104 1.25,0.292 0.188,0.188 10 true *c 1.344,1.354 1.531,1.542 0.188,0.188 10 true *a 0.24,2 0.427,2.188 0.188,0.188 10 true *a 2.875,2 3.063,2.188 0.188,0.188 10 true *a
*a Timing Mark
*b Groove
*c Approximately 13°


Check that the No. 1 cylinder is set to TDC/compression.

i.

Rotate the crankshaft two full rotations, and then check that all timing marks are in the position shown in the illustration.

HINT:

If the timing marks do not match, set the chain sub-assembly again.




Hide 11204 7.INSTALL CYLINDER HEAD COVER CONNECTOR SUB-ASSEMBLY

Hide 11201 8.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 17861 10.INSTALL INTAKE AIR CONNECTOR

Hide 16361A 11.INSTALL FAN AND GENERATOR V BELT

Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION