Home › Engine / Hybrid System › 1TR-FE ENGINE MECHANICAL › ENGINE UNIT
RM3250E _51 Engine / Hybrid System _037998 1TR-FE ENGINE MECHANICAL _0184012 ENGINE UNIT A

1TR-FE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 11381 1.INSTALL REAR ENGINE OIL SEAL RETAINER

a.

Clean and degrease the contact surfaces of the rear engine oil seal retainer and cylinder block.


b.
A346838C01
0.917,1.865 1.104,2.063 0.188,0.198 10 false *a
*a Seal Packing


Apply seal packing in a continuous bead as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the rear engine oil seal retainer within 3 minutes after applying seal packing.

·

Do not start the engine for at least 4 hours after installation.




c.

Install the rear engine oil seal retainer with the 6 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 15609 3.INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

a.

Install the oil filter bracket straight screw plug and a new gasket to the oil filter bracket sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


b.

Install 2 new O-rings, gasket and oil filter bracket with the union bolt and nut.

Torque:
for union bolt : 68.5 N*m (699 kgf*cm, 51 ft.*lbf)
for nut : 25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

Apply a light coat of engine oil to the new O-ring and oil filter bracket sub-assembly.



Hide 15600A 4.INSTALL OIL FILTER UNION

a.

Using a 27 mm socket wrench, install the oil filter union.

Torque:
43.1 N*m (439 kgf*cm, 32 ft.*lbf)


Hide 15601 5.INSTALL OIL FILTER SUB-ASSEMBLY

Hide 15678A 6.INSTALL OIL CONTROL VALVE FILTER

a.

Check that no foreign matter is on the mesh part of the oil control valve filter.

If foreign matter is present, clean the part thoroughly.


b.

Using an 8 mm hexagon wrench, install a new gasket and the oil control valve filter with the screw plug.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 11101 8.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 13070A 9.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13050 10.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13750 12.INSTALL VALVE LASH ADJUSTER ASSEMBLY

Hide 13801 13.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13516 17.INSTALL OIL JET

a.

Install the oil jet with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13471A 18.INSTALL CRANKSHAFT PULLEY SET KEY

a.

Install the 2 crankshaft pulley set keys to the crankshaft.


Hide 19315A 19.INSTALL CRANK POSITION SENSOR ROTOR

a.
A353228C01
1.667,0.813 2.25,0.417 2.25,0.417 2.417,0.417 true 1.875,0.906 2.25,0.417 true 2.51,1.021 2.75,0.667 2.75,0.667 2.917,0.667 true 2.438,0.344 2.75,0.5 0.313,0.156 10 false *1 2.917,0.583 3.167,0.75 0.25,0.167 10 false *a
*1 Crankshaft Pulley Set Key
*a Front Mark


Install the crank position sensor rotor with the front mark facing forward.


Hide 13521 20.INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET

a.
A353227C01
1.479,0.927 1.75,0.5 1.75,0.5 1.917,0.5 true 2.656,1.156 2.844,0.844 2.844,0.844 3.01,0.844 true 1.938,0.417 2.25,0.573 0.313,0.156 10 false *1 3.042,0.75 3.354,0.906 0.313,0.156 10 false *a
*1 Crankshaft Pulley Set Key
*a Key Groove


Install the crankshaft timing gear or sprocket as shown in the illustration.


Hide 13561 21.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.

Install the No. 1 chain vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13506 22.INSTALL CHAIN SUB-ASSEMBLY

a.
A337689C01
2.708,0.948 2.125,1.063 2.125,1.063 2.708,0.698 true 1.125,0.583 1.344,1.302 1.344,1.302 1.01,0.781 true 2.917,2.031 2.74,2.031 2.74,2.031 2.51,2.26 true 0.469,2.052 0.594,2.052 0.594,2.052 0.896,2.25 true 3.135,2.667 3.042,2.667 3.042,2.667 2.49,2.365 true 0.896,2.344 0.427,2.688 0.427,2.688 0.302,2.688 true 2.5,3.417 2.385,3.417 2.385,3.417 1.75,3.917 true 1.813,4.031 1.583,4.479 1.583,4.479 1.458,4.479 true 1.875,4.073 2.042,4.302 2.042,4.302 2.042,4.438 true 2.552,3.333 2.823,3.563 0.271,0.229 10 true *1 1.271,4.385 1.458,4.594 0.188,0.208 10 false *a 0.271,1.958 0.458,2.146 0.188,0.188 10 false *b 1.969,4.448 2.146,4.625 0.177,0.177 10 false *c 1.042,0.052 1.229,0.229 0.188,0.177 10 true *d 1.781,3.323 1.958,3.5 0.177,0.177 10 true *e 2.948,1.948 3.135,2.135 0.188,0.188 10 false *b 0.125,2.594 0.302,2.781 0.177,0.188 10 false *a 3.177,2.583 3.375,2.771 0.198,0.188 10 false *a 1.292,1.323 1.479,1.521 0.188,0.198 10 false *a 1.917,0.969 2.115,1.167 0.198,0.198 10 true *a
*1 Crankshaft Pulley Set Key
*a Timing Mark
*b Mark Plate (Yellow)
*c Mark Plate (Pink)
*d Approximately 13°
*e Approximately 30°


As shown in the illustration, install the chain sub-assembly to the camshaft timing exhaust gear assembly and camshaft timing gear assembly with the mark plates aligned with the timing marks on the camshaft timing exhaust gear assembly and camshaft timing gear assembly.

HINT:
·

The camshaft mark plate is yellow.

·

The crankshaft mark plate is pink.




b.
A340607

Use a rope to tie the chain sub-assembly of the crankshaft timing gear or sprocket. Tie the rope near the crankshaft timing gear or sprocket.

NOTICE:

After the No. 1 chain tensioner assembly has been installed, the rope must be removed.


HINT:

The rope is tied so that the chain sub-assembly will not jump a tooth.



Hide 13559 23.INSTALL CHAIN TENSIONER SLIPPER

a.

Install the chain tensioner slipper with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13540 24.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A101303C26
1.854,1.531 2.104,1.708 2.104,1.708 2.24,1.708 true 2.323,0.781 2.552,0.344 2.552,0.344 2.677,0.344 true 0.563,1.854 0.563,1.521 false 2.281,1.615 2.51,1.823 0.229,0.208 10 false *b 0.479,1.875 0.667,2.073 0.188,0.198 10 false *c 2.729,0.25 2.917,0.458 0.188,0.208 10 false *a
*a Plunger
*b Stopper Plate
*c Hexagon Wrench


Move the stopper plate upward to release the lock and push the plunger deep into the tensioner.


b.

Move the stopper plate downward to set the lock and insert a hexagon wrench into the hole of the stopper plate.


c.

Install a new gasket and the No. 1 chain tensioner assembly with the bolt and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Remove the hexagon wrench from the No. 1 chain tensioner assembly and release the plunger.


Hide 13566B 25.INSTALL TIMING CHAIN GUIDE

a.
A336451C02
0.646,1.729 0.875,1.729 0.875,1.729 1.552,1.063 true 0.438,1.625 0.635,1.813 0.198,0.188 10 false *1
*1 O-ring


Install a new O-ring to the No. 1 camshaft bearing cap.


b.

Install the timing chain guide with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 26.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A336450C01
0.427,2 0.594,2 0.594,2 0.885,2.323 true 2.896,2.031 2.76,2.031 2.76,2.031 2.49,2.365 true 2.885,3.75 2.75,3.75 2.75,3.75 1.771,3.917 true 1.833,4.031 2.063,4.302 2.063,4.302 2.063,4.417 true 2.698,0.938 2.052,1.083 2.052,1.083 2.708,0.698 true 1.125,0.573 1.333,1.281 1.333,1.281 1,0.781 true 2.927,3.646 3.125,3.875 0.198,0.229 10 false *1 1.281,1.302 1.479,1.51 0.198,0.208 10 true *a 1.052,0.042 1.24,0.24 0.188,0.198 10 true *b 1.76,3.313 1.958,3.5 0.198,0.188 10 true *c 1.865,0.99 2.063,1.198 0.198,0.208 10 true *a 2.938,1.917 3.135,2.125 0.198,0.208 10 true *a 0.229,1.885 0.427,2.094 0.198,0.208 10 true *a 1.979,4.427 2.177,4.635 0.198,0.208 10 true *a
*1 Crankshaft Pulley Set Key
*a Timing Mark
*b Approximately 13°
*c Approximately 30°


Check that the No. 1 cylinder is set to TDC/compression.

i.

Rotate the crankshaft two full rotations, and then check that all timing marks are in the position shown in the illustration.

If the timing marks do not match, set the chain sub-assembly again.



Hide 11204 27.INSTALL CYLINDER HEAD COVER CONNECTOR SUB-ASSEMBLY

a.

Install a new No. 2 camshaft bearing cap oil hole gasket and 3 new No. 3 camshaft bearing cap oil hole gaskets to the No. 1 camshaft bearing cap.


b.

Install the cylinder head cover connector sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16100 28.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 11302 29.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 16620D 30.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11421 32.INSTALL OIL PAN STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using an E6 "TORX" socket wrench, install the stud bolts.

A353232C01
3.25,1.75 3.083,1.75 3.083,1.75 2.854,1.323 true 3,2 2.833,2 2.833,2 2.594,1.542 true 3.75,0.167 3.583,0.167 3.583,0.167 3.365,0.552 true 2.052,2.51 2.365,2.667 0.313,0.156 10 false *a 2.052,3.073 2.365,3.229 0.313,0.156 10 false *b 2.729,2.74 3.042,2.896 0.313,0.156 10 false *c 4.76,2.74 5.073,2.896 0.313,0.156 10 false *d 5.385,2.927 5.698,3.083 0.313,0.156 10 false *e 4.76,3.146 5.073,3.302 0.313,0.156 10 false *d 3.281,1.667 3.438,1.865 0.156,0.198 10 false A 1.552,1.917 1.708,2.115 0.156,0.198 10 false A 3.021,1.917 3.177,2.115 0.156,0.198 10 false B 3.781,0.083 3.938,0.281 0.156,0.198 10 false B 4.375,2.271 4.531,2.469 0.156,0.198 10 false B
*a 16 mm (0.630 in.) *b 9.0 mm (0.354 in.)
*c 27 mm (1.06 in.) *d 9.0 mm (0.354 in.)
*e 19 mm (0.748 in.) - -


Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 12101 33.INSTALL OIL PAN SUB-ASSEMBLY

Hide 15104 34.INSTALL OIL STRAINER SUB-ASSEMBLY

Hide 12102A 35.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

Hide 12144 36.INSTALL OIL PAN COVER SILENCER

Hide 13471 37.INSTALL CRANKSHAFT PULLEY

Hide 16331A 38.INSTALL THERMOSTAT

Hide 16321 39.INSTALL WATER INLET

Hide 12233 40.INSTALL NO. 1 VENTILATION CONNECTOR

a.

Install the No. 1 ventilation connector to the cylinder head cover sub-assembly with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 11201 41.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11101J 42.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side)

Hide 11101J 43.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 11301K 44.INSTALL CRANKSHAFT POSITION SENSOR

Hide 11301M 45.INSTALL CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11301M 46.INSTALL CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 12204 47.INSTALL PCV VALVE SUB-ASSEMBLY

Hide 12108 48.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install the gasket to the oil filler cap sub-assembly.


b.

Install the oil filler cap sub-assembly.


Hide 89422 49.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

Hide 83530 51.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY