Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.06–2016.01
RM3250E _58 Vehicle Interior _038068 METER / GAUGE / DISPLAY _0184171 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The vehicle speed signal consists of pulses sent to the combination meter assembly from the speedometer sensor*1 or brake actuator assembly (skid control ECU)*2.

*1: w/o ABS

*2: w/ ABS


WIRING DIAGRAM

E323260E01
0.583,1.542 2.25,1.896 1.667,0.354 10 false Brake Actuator Assembly (Skid Control ECU)*3 1.99,0.74 3.656,1.094 1.667,0.354 10 false A4 2.417,0.74 4.083,1.094 1.667,0.354 10 false A3 1.938,0.542 3.604,0.896 1.667,0.354 10 false 14*1 1.521,0.646 3.188,1 1.667,0.354 10 false SP1 2.365,0.542 4.031,0.896 1.667,0.354 10 false 22*2 5.438,0.646 6.448,1.031 1.01,0.385 10 false SI 3.521,1.74 4.531,2.125 1.01,0.385 10 false SI 3.781,1.74 4.792,2.125 1.01,0.385 10 false 3 2.542,2.625 4.208,2.979 1.667,0.354 10 false C62 2.542,2.771 4.208,3.125 1.667,0.354 10 false Speedometer Sensor*4 0.906,4.49 2.573,4.844 1.667,0.354 10 false ECM 1.26,3.958 2.927,4.313 1.667,0.354 10 false SPD 1.281,5.813 2.948,6.167 1.667,0.354 10 false SPD 5.688,5.802 6.427,6.375 0.74,0.573 10 false SPD 5.427,3.958 6.167,4.531 0.74,0.573 10 false +S 5.156,3.969 5.896,4.542 0.74,0.573 10 false 19 5.146,0.625 5.885,1.198 0.74,0.573 10 false 18 5.271,4.552 7.125,5.01 1.854,0.458 10 false G9 5.271,4.719 7.125,5.177 1.854,0.458 10 false Combination Meter Assembly 6.417,3.708 6.99,4.156 0.573,0.448 10 false CPU 1.729,4.073 2.469,4.646 0.74,0.573 10 false G88 2.167,4.073 2.906,4.646 0.74,0.573 10 false G45 2.594,4.063 3.333,4.635 0.74,0.573 10 false G85 3.01,4.073 3.75,4.646 0.74,0.573 10 false G83 1.719,3.875 2.458,4.448 0.74,0.573 10 false 12*5 2.156,3.875 2.896,4.448 0.74,0.573 10 false 23*6 2.563,3.865 3.302,4.438 0.74,0.573 10 false 10*7 2.979,3.865 3.719,4.438 0.74,0.573 10 false 17*8 0.458,6.323 2.125,6.677 1.667,0.354 10 false G69 0.458,6.49 2.125,6.844 1.667,0.354 10 false Certification ECU (Smart Key ECU Assembly)*9 5.792,6.365 6.698,6.667 0.906,0.302 10 false G27 5.802,6.531 6.708,6.833 0.906,0.302 10 false Body ECU*10 5.49,5.813 6.396,6.115 0.906,0.302 10 false 5 0.323,7.167 2.021,7.417 1.698,0.25 10 false *1: w/ VSC 0.323,7.438 2.021,7.688 1.698,0.25 10 false *2: w/o VSC 0.333,7.719 2.031,7.969 1.698,0.25 10 false *3: w/ ABS 0.344,7.99 2.042,8.24 1.698,0.25 10 false *4: w/o ABS 0.344,8.26 2.042,8.51 1.698,0.25 10 false *5: for 1GR-FE 1.521,7.135 3.385,7.365 1.865,0.229 10 false *6: for 1TR-FE, 2TR-FE 1.51,7.417 3.375,7.646 1.865,0.229 10 false *7: for 1GD-FTV, 2GD-FTV 1.521,7.708 3.385,7.938 1.865,0.229 10 false *8: for 1KD-FTV, 2KD-FTV 1.531,7.969 3.396,8.198 1.865,0.229 10 false *9: w/ Entry and Start System 1.542,8.271 5.51,8.469 3.969,0.198 10 false *10: w/ Body ECU 1.708,5.802 3.375,6.156 1.667,0.354 10 false 7

E323261E01
1.688,2.802 2,3 0.313,0.198 10 false 17 5.406,2.813 5.719,3.01 0.313,0.198 10 false 17 5.667,2.813 5.979,3.01 0.313,0.198 10 false SPD 1.323,2.823 1.635,3.021 0.313,0.198 10 false SPD 1.323,0.969 1.635,1.167 0.313,0.198 10 false SPD 5.688,0.969 6.115,1.198 0.427,0.229 10 false SPD1 5.875,1.469 6.188,1.667 0.313,0.198 10 false G90 5.427,0.969 5.74,1.167 0.313,0.198 10 false 25 5.875,1.646 6.813,2.104 0.938,0.458 10 false TCM*1 0.365,1.479 1.302,1.938 0.938,0.458 10 false G113 0.365,1.646 2.448,2.167 2.083,0.521 10 false Navigation Receiver Assembly*2 0.333,3.323 2.052,3.833 1.719,0.51 10 false G37 0.354,3.479 2.073,3.99 1.719,0.51 10 false Radio and Display Receiver Assembly*3 5.302,3.323 7.042,3.813 1.74,0.49 10 false G117 5.313,3.5 7.052,3.99 1.74,0.49 10 false Radio Receiver Assembly*4 0.177,4.469 3.49,4.813 3.313,0.344 10 false *1: for KD Series Engine, Automatic Transmission 0.177,4.823 3.49,5.167 3.313,0.344 10 false *2: w/ Navigation System 0.156,5.156 4.01,5.448 3.854,0.292 10 false *3: w/ Audio and Visual System (for Radio and Display Type) 0.156,5.479 4.01,5.771 3.854,0.292 10 false *4: w/ Audio and Visual System (for Radio Receiver Type) 1.708,0.969 2.021,1.167 0.313,0.198 10 false 17

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, make sure to replace it with a new one.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

·

w/ Entry and Start System:

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

w/ Audio and Visual System (for Radio and Display Type):

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>PRECAUTION

·

If the body ECU has been replaced, it is necessary to initialize the body ECU.



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
NOTICE:

For vehicles without an entry and start system, go to "Check Body ECU".


*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Body ECU

*6: for KD Series Engine, Automatic Transmission

*7: w/ Navigation System

*8: w/ Audio and Visual System (for Radio and Display Type)

*9: w/ Audio and Visual System (for Radio Receiver Type)


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3 or G83*4 ECM connector.


c.

Disconnect the G27 body ECU connector.*5


d.

Disconnect the G90 TCM connector.*6


e.

Disconnect the G113 navigation receiver assembly connector.*7


f.

Disconnect the G37 radio and display receiver assembly connector.*8


g.

Disconnect the G117 radio receiver assembly connector.*9


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK BODY ECU

NG

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
2.CHECK BODY ECU
NOTICE:

For vehicles without a body ECU, go to "Check TCM".


*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: for KD Series Engine, Automatic Transmission

*7: w/ Navigation System

*8: w/ Audio and Visual System (for Radio and Display Type)

*9: w/ Audio and Visual System (for Radio Receiver Type)


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3 or G83*4 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G90 TCM connector.*6


e.

Disconnect the G113 navigation receiver assembly connector.*7


f.

Disconnect the G37 radio and display receiver assembly connector.*8


g.

Disconnect the G117 radio receiver assembly connector.*9


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK TCM

NG

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)
3.CHECK TCM
NOTICE:

For vehicles without a KD series engine, automatic transmission, go to "Check Navigation Receiver Assembly".


*1: w/ Entry and Start System

*2: w/ Body ECU

*3: w/ Navigation System

*4: w/ Audio and Visual System (for Radio and Display Type)

*5: w/ Audio and Visual System (for Radio Receiver Type)


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G83 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*1


d.

Disconnect the G27 body ECU connector.*2


e.

Disconnect the G113 navigation receiver assembly connector.*3


f.

Disconnect the G37 radio and display receiver assembly connector.*4


g.

Disconnect the G117 radio receiver assembly connector.*5


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK NAVIGATION RECEIVER ASSEMBLY

NG

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
4.CHECK NAVIGATION RECEIVER ASSEMBLY
NOTICE:

For vehicles without a navigation system, go to "Check Radio and Display Receiver Assembly".


*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Body ECU

*7: for KD Series Engine, Automatic Transmission


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3 or G83*4 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.*6


e.

Disconnect the G90 TCM connector.*7


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
5.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
NOTICE:

For vehicles without an audio and visual system (for radio and display type), go to "Check Radio Receiver Assembly".


*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Body ECU

*7: for KD Series Engine, Automatic Transmission


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3 or G83*4 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.*6


e.

Disconnect the G90 TCM connector.*7


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK RADIO RECEIVER ASSEMBLY

NG

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
6.CHECK RADIO RECEIVER ASSEMBLY
NOTICE:

For vehicles without an audio and visual system (for radio receiver type), go to "Check ECM".


*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Body ECU

*7: for KD Series Engine, Automatic Transmission


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3 or G83*4 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.*6


e.

Disconnect the G90 TCM connector.*7


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK ECM

NG

16.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)
7.CHECK ECM

*1: w/ Entry and Start System

*2: w/ Body ECU

*3: for KD Series Engine, Automatic Transmission

*4: w/ Navigation System

*5: w/ Audio and Visual System (for Radio and Display Type)

*6: w/ Audio and Visual System (for Radio Receiver Type)


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*1


c.

Disconnect the G27 body ECU connector.*2


d.

Disconnect the G90 TCM connector.*3


e.

Disconnect the G113 navigation receiver assembly connector.*4


f.

Disconnect the G37 radio and display receiver assembly connector.*5


g.

Disconnect the G117 radio receiver assembly connector.*6


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK VEHICLE TYPE

NG

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
8.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ ABS A
w/o ABS B



A

9.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

B

18.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
9.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.
C317099C04
1.448,2.479 1.896,2.771 0.448,0.292 1.458,0.125 1.906,0.417 0.448,0.292 0.51,1.729 0.688,1.729 0.688,1.729 1.094,1.021 true 2.531,4.406 2.344,4.406 2.344,4.406 1.958,3.594 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 2.604,4.313 3.219,4.51 0.615,0.198 10 false SP1 1.604,0.177 1.917,0.375 0.313,0.198 10 false A4 1.594,2.531 1.906,2.729 0.313,0.198 10 false A3 1.979,0.198 2.292,0.396 0.313,0.198 10 false *A 1.958,2.542 2.271,2.74 0.313,0.198 10 false *B 0.177,1.594 0.792,1.792 0.615,0.198 10 false SP1
*A w/ VSC
*B w/o VSC
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ VSC
Tester Connection Switch Condition Specified Condition
A4-14 (SP1) - Body ground Ignition switch ON 11 to 14 V

w/o VSC
Tester Connection Switch Condition Specified Condition
A3-22 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

19.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
10.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
a.
E200403C12
1.521,0.26 1.917,0.479 0.396,0.219 1.052,1.125 0.771,0.865 0.771,0.865 0.615,0.865 true 0.406,0.76 0.708,1.073 0.302,0.313 10 false SI 1.625,0.281 1.99,0.469 0.365,0.188 10 false G9 1.333,4.094 1.458,4.24 0.125,0.146 10 false A 2.969,3.51 3.427,3.885 0.458,0.375 10 false GND 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.094,2.448 0.406,2.604 0.313,0.156 10 false *b
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Connect an oscilloscope to terminal G9-18 (SI) and body ground.


c.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Tester Connection G9-18 (SI) - Body ground
Tool Setting 5 V/DIV, 20 ms./DIV
Vehicle Condition Driving at approximately 20 km/h (12 mph)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Body ECU

*6: for KD Series Engine, Automatic Transmission

*7: w/ Navigation System

*8: w/ Audio and Visual System (for Radio and Display Type)

*9: w/ Audio and Visual System (for Radio Receiver Type)


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3 or G83*4 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G27 body ECU connector.*5


e.

Disconnect the G90 TCM connector.*6


f.

Disconnect the G113 navigation receiver assembly connector.*7


g.

Disconnect the G37 radio and display receiver assembly connector.*8


h.

Disconnect the G117 radio receiver assembly connector.*9


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G69-7 (SPD) Always Below 1 Ω
G9-19 (+S) or G69-7 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)

*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: for KD Series Engine, Automatic Transmission

*7: w/ Navigation System

*8: w/ Audio and Visual System (for Radio and Display Type)

*9: w/ Audio and Visual System (for Radio Receiver Type)


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3 or G83*4 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.


e.

Disconnect the G90 TCM connector.*6


f.

Disconnect the G113 navigation receiver assembly connector.*7


g.

Disconnect the G37 radio and display receiver assembly connector.*8


h.

Disconnect the G117 radio receiver assembly connector.*9


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G27-5 (SPD) Always Below 1 Ω
G9-19 (+S) or G27-5 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)

*1: w/ Entry and Start System

*2: w/ Body ECU

*3: w/ Navigation System

*4: w/ Audio and Visual System (for Radio and Display Type)

*5: w/ Audio and Visual System (for Radio Receiver Type)


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G83 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*1


d.

Disconnect the G27 body ECU connector.*2


e.

Disconnect the G90 TCM connector.


f.

Disconnect the G113 navigation receiver assembly connector.*3


g.

Disconnect the G37 radio and display receiver assembly connector.*4


h.

Disconnect the G117 radio receiver assembly connector.*5


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G90-25 (SPD1) Always Below 1 Ω
G9-19 (+S) or G90-25 (SPD1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)

*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Body ECU

*7: for KD Series Engine, Automatic Transmission


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3 or G83*4 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.*6


e.

Disconnect the G90 TCM connector.*7


f.

Disconnect the G113 navigation receiver assembly connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G113-17 (SPD) Always Below 1 Ω
G9-19 (+S) or G113-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Body ECU

*7: for KD Series Engine, Automatic Transmission


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3 or G83*4 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.*6


e.

Disconnect the G90 TCM connector.*7


f.

Disconnect the G37 radio receiver assembly connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G37-17 (SPD) Always Below 1 Ω
G9-19 (+S) or G37-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)

*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Body ECU

*7: for KD Series Engine, Automatic Transmission


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3 or G83*4 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.*6


e.

Disconnect the G90 TCM connector.*7


f.

Disconnect the G117 radio receiver assembly connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G117-17 (SPD) Always Below 1 Ω
G9-19 (+S) or G117-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Body ECU

*7: for KD Series Engine, Automatic Transmission

*8: w/ Navigation System

*9: w/ Audio and Visual System (for Radio and Display Type)

*10: w/ Audio and Visual System (for Radio Receiver Type)


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3 or G83*4 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.*6


e.

Disconnect the G90 TCM connector.*7


f.

Disconnect the G113 navigation receiver assembly connector.*8


g.

Disconnect the G37 radio and display receiver assembly connector.*9


h.

Disconnect the G117 radio receiver assembly connector.*10


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE
Tester Connection Condition Specified Condition
G9-19 (+S) - G88-12 (SPD) Always Below 1 Ω
G9-19 (+S) or G88-12 (SPD) - Body ground Always 10 kΩ or higher

for 1TR-FE, 2TR-FE
Tester Connection Condition Specified Condition
G9-19 (+S) - G45-23 (SPD) Always Below 1 Ω
G9-19 (+S) or G45-23 (SPD) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV
Tester Connection Condition Specified Condition
G9-19 (+S) - G85-10 (SPD) Always Below 1 Ω
G9-19 (+S) or G85-10 (SPD) - Body ground Always 10 kΩ or higher

for 1KD-FTV, 2KD-FTV
Tester Connection Condition Specified Condition
G9-19 (+S) - G83-17 (SPD) Always Below 1 Ω
G9-19 (+S) or G83-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
a.
E200403C12
1.521,0.26 1.917,0.479 0.396,0.219 1.052,1.125 0.771,0.865 0.771,0.865 0.615,0.865 true 0.406,0.76 0.708,1.073 0.302,0.313 10 false SI 1.625,0.281 1.99,0.469 0.365,0.188 10 false G9 1.333,4.094 1.458,4.24 0.125,0.146 10 false A 2.969,3.51 3.427,3.885 0.458,0.375 10 false GND 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.094,2.448 0.406,2.604 0.313,0.156 10 false *b
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Connect an oscilloscope to terminal G9-18 (SI) and body ground.


c.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Tester Connection G9-18 (SI) - Body ground
Tool Setting 5 V/DIV, 20 ms./DIV
Vehicle Condition Driving at approximately 20 km/h (12 mph)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

20.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)
19.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the A4*1 or A3*2 brake actuator assembly (skid control ECU) connector.

*1: w/ VSC

*2: w/o VSC



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ VSC
Tester Connection Condition Specified Condition
G9-18 (SI) - A4-14 (SP1) Always Below 1 Ω
G9-18 (SI) or A4-14 (SP1) - Body ground Always 10 kΩ or higher

w/o VSC
Tester Connection Condition Specified Condition
G9-18 (SI) - A3-22 (SP1) Always Below 1 Ω
G9-18 (SI) or A3-22 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the C62 speedometer sensor connector.


b.

Disconnect the G9 and G10 combination meter assembly connectors.


c.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C62-3 (SI) - G9-18 (SI) Always Below 1 Ω
C62-3 (SI) or G9-9 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR