Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM
RM3250E _51 Engine / Hybrid System _037990 1KD-FTV ENGINE CONTROL _0184269 ECD SYSTEM J

1KD-FTV ENGINE CONTROL  ECD SYSTEM  Injector Circuit  


DESCRIPTION

The injector driver drives the injectors at high speeds with a high-voltage DC/DC converter. The ECM constantly monitors the injector driver and stops the engine if an abnormal condition is detected.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK INJECTOR DRIVER (POWER SOURCE)
a.

Disconnect the injector driver connectors.


b.
A221614C63
0.51,1.396 0.896,1.656 0.385,0.26 1.677,1.188 1.156,0.844 true 2.427,1.646 1.969,1.26 true 0.583,1.448 0.865,1.604 0.281,0.156 10 false C82 0.729,0.719 1.208,0.979 0.479,0.26 10 false +B (+) 0.073,0.094 0.271,0.25 0.198,0.156 10 false *a 2.458,1.635 3.021,1.854 0.563,0.219 10 false GND (-)
*a Front view of wire harness connector
(to Injector Driver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C82-2 (+B) - C82-3 (GND) Ignition switch ON 11 to 14 V



c.

Reconnect the injector driver connector.


Result:
Proceed to
OK
NG



OK

NG

2.INSPECT EDU RELAY
2.INSPECT EDU RELAY
a.

Inspect the EDU relay from engine room relay block.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (EDU RELAY - INJECTOR DRIVER)

NG

REPLACE EDU RELAY

3.CHECK HARNESS AND CONNECTOR (EDU RELAY - INJECTOR DRIVER)
a.

Remove the EDU relay from the engine room relay block and junction block assembly.


b.

Disconnect the injector driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C82-2 (+B) - EDU relay tarminal 5 Always Below 1 Ω
C82-3 (GND) - Body ground Always Below 1 Ω
C82-2 (+B) or EDU relay tarminal 5 - Body ground Always 10 kΩ or higher



d.

Reconnect the injector driver connector.


e.

Reinstall the EDU relay.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (EDU RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (EDU RELAY - ECM)
a.

Remove the EDU relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-10 (IREL) - EDU relay tarminal 2 Always Below 1 Ω
G84-10 (IREL) or EDU relay tarminal 2 - Bodyground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reinstall the EDU relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR