Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › 2015.06–2016.01
RM3250E _58 Vehicle Interior _038073 HEATING / AIR CONDITIONING _0184341 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1413/13  Evaporator Temperature Sensor Circuit  


DESCRIPTION

The No. 1 cooler thermistor (evaporator temperature sensor) is installed on the evaporator in the air conditioner unit to detect the temperature of the air that has passed through the evaporator and is used to control the air conditioning. It sends signals to the air conditioning amplifier assembly. The resistance of the No. 1 cooler thermistor (evaporator temperature sensor) changes in accordance with the cooled air temperature that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler thermistor (evaporator temperature sensor) and reads voltage changes as the resistance of the No. 1 cooler thermistor (evaporator temperature sensor) changes. This sensor is used for frost prevention.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1413/13 Evaporator Temperature Sensor Circuit Open or short in No. 1 cooler thermistor (evaporator temperature sensor) circuit
·

No. 1 cooler thermistor (evaporator temperature sensor)

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly


Memorized (4 seconds or more) -

HINT:

The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the parentheses.


WIRING DIAGRAM

E316646E04
4.656,1.615 4.969,1.813 0.313,0.198 10 false za 4.667,1.76 6.906,2.021 2.24,0.26 10 false Air Conditioning Amplifier Assembly 6.167,0.635 6.479,0.833 0.313,0.198 10 false AD 5.719,0.219 6.031,0.417 0.313,0.198 10 false 5 V 4.792,0.521 5.104,0.719 0.313,0.198 10 false TE 4.813,1 5.281,1.198 0.469,0.198 10 false SG-4 4.51,0.521 4.823,0.719 0.313,0.198 10 false 6 4.5,0.99 4.969,1.188 0.469,0.198 10 false 5 3.094,1.365 4.625,1.771 1.531,0.406 10 false Air Conditioning Harness Assembly 3,0.521 3.313,0.719 0.313,0.198 10 false 2 3.01,1 3.323,1.198 0.313,0.198 10 false 1 0.708,1.521 2.885,1.979 2.177,0.458 10 false No. 1 Cooler Thermistor (Evaporator Temperature Sensor)

CAUTION / NOTICE / HINT

NOTICE:

When the servo motor or air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS (EVAPORATOR FIN THERMISTOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Evaporator Fin Thermistor No. 1 cooler thermistor (evaporator temperature sensor) Min.: -29.70°C (-21.46°F)
Max.: 59.55°C (139.19°F)
Actual evaporator temperature displayed No. 1 cooler thermistor (evaporator temperature sensor) system malfunction:
·

When open circuit: -29.70°C (-21.46°F)

·

When short circuit: 59.55°C (139.19°F)


Body Electrical > Air Conditioner > Data List
Tester Display
Evaporator Fin Thermistor
50003 121 3
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

C

2.INSPECT NO. 1 COOLER THERMISTOR
2.INSPECT NO. 1 COOLER THERMISTOR
a.

Remove the No. 1 cooler thermistor (evaporator temperature sensor).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT EVAPORATOR TEMPERATURE SENSOR>REMOVAL


b.

Inspect the No. 1 cooler thermistor (evaporator temperature sensor).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT EVAPORATOR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK AIR CONDITIONING HARNESS ASSEMBLY

NG

REPLACE NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)

3.CHECK AIR CONDITIONING HARNESS ASSEMBLY
a.
E312532C06
1.469,2.26 1.875,2.49 0.406,0.229 2.698,3.083 2.531,3.083 2.531,3.083 2.365,2.667 true 1.75,3.083 1.917,3.083 1.917,3.083 2.125,2.667 true 0.813,1.167 1.063,0.75 1.063,0.75 1.396,0.75 true 1.438,0.656 1.75,0.854 0.313,0.198 10 false *1 0.104,0.74 0.417,0.938 0.313,0.198 10 false *a 1.438,1.188 1.75,1.385 0.313,0.198 10 false *b 1.844,0.115 2.156,0.313 0.313,0.198 10 false *c 1.875,1.531 2.188,1.729 0.313,0.198 10 false *d 1.406,3 1.906,3.198 0.5,0.198 10 false SG-4 2.729,3 3.229,3.198 0.5,0.198 10 false TE 1.604,2.292 1.917,2.49 0.313,0.198 10 false za
*1 Air Conditioning Harness Assembly
*a To No. 1 Cooler Thermistor (Evaporator Temperature Sensor) Connection Connector
*b To Air Conditioning Amplifier Assembly Connection Connector
*c Front view of air conditioning harness assembly
(to Air Conditioning Amplifier Assembly)
*d Front view of air conditioning harness assembly
(to No. 1 Cooler Thermistor [Evaporator Temperature Sensor])


Disconnect the air conditioning harness assembly connector.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
za-6 (TE) - 2 Always Below 1 Ω
za-5 (SG-4) - 1 Always Below 1 Ω
1 - 2 Always 10 kΩ or higher
za-6 (TE) or 2 - Body ground Always 10 kΩ or higher
za-5 (SG-4) or 1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG