Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM
RM3250E _58 Vehicle Interior _038072 SEAT BELT _0184383 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Front Passenger Side Seat Belt Warning Light Malfunction  


DESCRIPTION

When the ignition switch is ON, the combination meter assembly monitors the state of the front passenger side seat and the front seat inner belt assembly RH*1 or LH*2 and also whether the front passenger seat is occupied. If the front passenger side seat belt is not fastened, the seat belt warning light of the combination meter assembly blinks. If the seat belt is fastened, the warning light goes off.

*1: for LHD

*2: for RHD


HINT:

The seat belt warning light on the combination meter assembly is used for both the driver side seat and front passenger side seat.


WIRING DIAGRAM

E324459E03
0.406,2.042 4.229,2.24 3.823,0.198 10 false Occupant Detection Sensor 0.552,2.844 2.156,3.177 1.604,0.333 10 false Separate Type Front Seat Cushion Pad 5.167,2.521 5.479,2.719 0.313,0.198 10 false G10 5.188,2.719 7.156,3.115 1.969,0.396 10 false Combination Meter Assembly 5.094,1.104 5.708,1.302 0.615,0.198 10 false P/SB 4.844,0.823 5,1.021 0.156,0.198 10 false 4 4.115,0.823 4.271,1.021 0.156,0.198 10 false 3 4.125,1.771 4.281,1.969 0.156,0.198 10 false 2 2.635,2.833 4.469,3.031 1.833,0.198 10 false N17*1, N18*2 2.635,3.031 4.573,3.385 1.938,0.354 10 false Front Seat Inner Belt Assembly RH*1, LH*2 0.167,3.948 1.854,4.146 1.688,0.198 10 false *1: for LHD 0.177,4.333 1.865,4.531 1.688,0.198 10 false *2: for RHD 6.229,1.427 6.688,1.625 0.458,0.198 10 false CPU 5.583,1.479 6.042,1.677 0.458,0.198 10 false I/F 3.844,0.823 4,1.021 0.156,0.198 10 false + 3.844,1.76 4,1.958 0.156,0.198 10 false E 2.917,2.042 4.75,2.24 1.833,0.198 10 false Buckle Switch

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, make sure to replace it with a new one.


PROCEDURE

1.READ VALUE USING GTS (P-SEATBELT BUCKLE SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P-Seatbelt Buckle SW Front passenger seat belt buckle switch signal ON or OFF ON: Front passenger seat belt not fastened
OFF: Front passenger seat belt fastened
Perform the inspection while sitting in the front passenger side seat.
Body Electrical > Combination Meter > Data List
Tester Display
P-Seatbelt Buckle SW
50003 122 7

Result:
Result Proceed to
ON or OFF is displayed on the GTS screen according to the front passenger side seat belt condition and front passenger seat condition (occupied or unoccupied) A
ON or OFF is not displayed normally on the GTS screen according to the front passenger side seat belt condition (for LHD) B
ON or OFF is not displayed normally on the GTS screen according to the front passenger side seat belt condition (for RHD) C



A

REPLACE COMBINATION METER ASSEMBLY

B

2.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

5.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the N17 front seat inner belt assembly RH connector.


b.

Disconnect the G10 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N17-3 (+) - G10-4 (P/SB) Always Below 1 Ω
N17-2 (E) - Body ground Always Below 1 Ω
N17-3 (+) or G10-4 (P/SB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH


Result:
Result Proceed to
OK A
NG (for Manual Seat) B
NG (for Power Seat) C
NG (for Bench Seat Type) D



A

4.INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

B

C

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

D

4.INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)
a.

Remove the separate type front seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL


b.

Inspect the separate type front seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

5.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the N18 front seat inner belt assembly LH connector.


b.

Disconnect the G10 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N18-3 (+) - G10-4 (P/SB) Always Below 1 Ω
N18-2 (E) - Body ground Always Below 1 Ω
N18-3 (+) or G10-4 (P/SB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH


Result:
Result Proceed to
OK A
NG (for Manual Seat) B
NG (for Power Seat) C
NG (for Bench Seat Type) D



A

4.INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

B

C

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

D