Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM3250E _58 Vehicle Interior _038073 HEATING / AIR CONDITIONING _0184341 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Viscous Heater with Magnet Clutch Circuit  


DESCRIPTION

When the heater switch assembly is pushed, the air conditioning amplifier assembly turns on the viscous heater relay and operates the viscous heater. If the viscous heater does not operate when the heater switch assembly is pushed, there may be a problem in the circuit shown below.

WIRING DIAGRAM

E322902E01
5.458,2.083 5.917,2.281 0.458,0.198 10 false MG+ 5.417,0.885 5.875,1.083 0.458,0.198 10 false SWVC 5.177,0.885 5.635,1.083 0.458,0.198 10 false 4 5.104,2.083 5.563,2.281 0.458,0.198 10 false 19 5.25,2.906 5.708,3.104 0.458,0.198 10 false G33 5.26,3.063 6.844,3.563 1.583,0.5 10 false Air Conditioning Amplifier Assembly 2.542,1.354 3,1.552 0.458,0.198 10 false G76 2.542,1.5 4.083,1.75 1.542,0.25 10 false Heater Switch Assembly 3.896,0.885 4.188,1.083 0.292,0.198 10 false IN 4.156,0.885 4.448,1.083 0.292,0.198 10 false 1 3.917,0.438 4.208,0.635 0.292,0.198 10 false E 4.156,0.438 4.448,0.635 0.292,0.198 10 false 5 2.542,0.438 2.833,0.635 0.292,0.198 10 false IG 2.333,0.438 2.625,0.635 0.292,0.198 10 false 4 1.521,0.719 2.229,0.917 0.708,0.198 10 false IG1 NO.4 0.375,0.552 0.938,1.438 0.563,0.885 10 false from IG1 NO.1 Relay*1, Ignition Switch*2 0.052,2.208 0.958,2.792 0.906,0.583 10 false from IG1 NO.2 Relay 1.51,2.354 2.219,2.552 0.708,0.198 10 false IG1 NO.5 3.042,2.948 3.917,3.198 0.875,0.25 10 false VISCOUS 3.906,2.083 4.365,2.281 0.458,0.198 10 false 1 3.917,2.5 4.375,2.698 0.458,0.198 10 false 3 2.719,2.083 3.177,2.281 0.458,0.198 10 false 2 2.719,2.5 3.177,2.698 0.458,0.198 10 false 5 2.573,4.063 4.208,4.313 1.635,0.25 10 false Magnet Clutch Assembly 2.521,4.521 4.156,4.771 1.635,0.25 10 false C107 2.531,4.667 4.25,5.083 1.719,0.417 10 false Viscous with Magnet Clutch Heater Assembly 3.792,3.552 4.25,3.75 0.458,0.198 10 false MG+ 4.208,3.542 4.667,3.74 0.458,0.198 10 false 1 0.167,5.188 2.208,5.417 2.042,0.229 10 false *1: w/ Entry and Start System 0.167,5.438 2.208,5.667 2.042,0.229 10 false *2: w/o Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

When the servo motor or air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>INITIALIZATION


HINT:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS (IDLE UP/PWR HEAT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IDLE UP/PWR HEAT Switch Heater switch assembly ON or OFF ON: Heater switch assembly on
OFF: Heater switch assembly off
-
Body Electrical > Air Conditioner > Data List
Tester Display
IDLE UP/PWR HEAT Switch
50003 121 173
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

3.CHECK HARNESS AND CONNECTOR (HEATER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Viscous Heater Viscous heater relay ON/OFF -
Body Electrical > Air Conditioner > Active Test
Tester Display
Viscous Heater
50004 121 67
OK:

Viscous heater relay operates.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

6.INSPECT VISCOUS HEATER RELAY (VISCOUS)
3.CHECK HARNESS AND CONNECTOR (HEATER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
E322903C01
1.448,0.219 1.948,0.469 0.5,0.25 1.896,1.365 2.052,1.969 2.052,1.969 2.385,1.969 true 2.094,1.365 2.333,1.688 2.333,1.688 2.667,1.688 true 2.458,1.885 2.771,2.083 0.313,0.198 10 false IG 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 1.563,0.26 1.979,0.458 0.417,0.198 10 false G76 2.719,1.594 3.031,1.792 0.313,0.198 10 false E
*a Front view of wire harness connector
(to Heater Switch Assembly)


Disconnect the heater switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G76-5 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G76-4 (IG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT HEATER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT HEATER SWITCH ASSEMBLY
a.

Remove the heater switch assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>HEATER SWITCH>REMOVAL


b.

Inspect the heater switch assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>HEATER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (HEATER SWITCH ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (HEATER SWITCH ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the G76 heater switch assembly connector


b.

Disconnect the G33 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G76-1 (IN) - G33-4 (SWVC) Always Below 1 Ω
G76-1 (IN) or G33-4 (SWVC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT VISCOUS HEATER RELAY (VISCOUS)
a.

Remove the viscous heater relay (VISCOUS) from the No. 5 instrument panel relay block.


b.

Inspect the viscous heater relay (VISCOUS).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)

NG

REPLACE VISCOUS HEATER RELAY

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)
a.

Disconnect the air conditioning amplifier assembly connector.


b.
E269948C35
1.458,0.333 1.969,0.583 0.51,0.25 0.375,0.75 0.625,0.75 0.625,0.75 0.875,1.25 true 0.042,0.052 0.354,0.25 0.313,0.198 10 false *a 1.583,0.375 1.896,0.573 0.313,0.198 10 false G33 0.052,0.667 0.521,0.854 0.469,0.188 10 false MG+
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G33-19 (MG+) - Body ground Ignition switch off Below 1 V
G33-19 (MG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY
a.

Remove the compressor assembly with magnet clutch.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER>REMOVAL


b.

Inspect the compressor assembly with magnet clutch.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (VISCOUS RELAY - VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY AND BATTERY)

NG

REPLACE VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (VISCOUS RELAY - VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY AND BATTERY)
a.

Remove the viscous heater relay (VISCOUS) from the No. 5 instrument panel relay block.


b.

Disconnect the C107 viscous with magnet clutch heater assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - C107-1 (MG+) Always Below 1 Ω
Relay terminal 3 or C107-1 (MG+) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Relay terminal 2 - Body ground Ignition switch off Below 1 V
Relay terminal 2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR