Home › Drivetrain › R151F MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION ASSEMBLY › 2015.06–2016.01
RM3250E _52 Drivetrain _038034 R151F MANUAL TRANSMISSION / TRANSAXLE _0185606 MANUAL TRANSMISSION ASSEMBLY A

R151F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the manual transmission assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link

Gas leak from exhaust system is repaired


Inspection After Repair Poor idle, engine start, etc. (Click here)

CAUTION:
·
C313282C03
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.

·
A350542

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 58810J 3.REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58811A 4.REMOVE FRONT CONSOLE BOX (w/o Console Box Lid)

Hide 58280A 5.REMOVE SHIFT LEVER BOOT ASSEMBLY

a.
C332864

Remove the 6 screws, 4 clips and shift lever boot assembly.


Hide 33530F 6.REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY

a.
C332406

Detach the shift lever cap boot from the manual transmission.


b.

Cover the shift lever cap with a cloth.


c.
C328999C02
1.938,0.49 2.25,0.156 2.25,0.156 2.448,0.156 true 1.865,0.802 2.031,1 0.167,0.198 10 false *a 1.75,2.354 1.948,2.531 0.198,0.177 10 false *b 1.156,3.219 1.354,3.406 0.198,0.188 10 false *c 2.51,0.052 2.677,0.25 0.167,0.198 10 false *1
*1 Shift Lever Cap
*a Press Down
*b Counterclockwise
*c Pull out


While pressing down on the shift lever cap, turn it counterclockwise, and then pull to remove the shift lever.


Hide 7.DRAIN MANUAL TRANSMISSION OIL

a.

Remove the drain plug sub-assembly and gasket, and then drain the manual transmission oil.


b.

Install a new gasket and the drain plug sub-assembly.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 51410 8.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442 9.REMOVE NO. 2 ENGINE UNDER COVER

Hide 51407A 10.REMOVE NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 37100 12.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 17410 13.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 15.DISCONNECT WIRE HARNESS

a.
C332407

Disconnect the 6 clamps and 2 connectors.


Hide 16.DISCONNECT GROUND CABLE

a.
C332408

Remove the bolt and disconnect the ground cable.


Hide 28100 17.REMOVE STARTER ASSEMBLY

Hide 18.SUPPORT MANUAL TRANSMISSION ASSEMBLY

a.
C160886

Support the manual transmission with a transmission jack.

NOTICE:
·

Make sure the high transmission jack attachment is centered on the safety stand.

·

Secure the part with a rope, attachment, etc.




Hide 51204 19.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C332409

Remove the 4 set bolts of the rear engine mounting insulator.


b.
C325680

Remove the 4 bolts, 4 nuts and No. 3 frame crossmember sub-assembly.


Hide 12371A 20.REMOVE REAR ENGINE MOUNTING INSULATOR

a.
C332410

Remove the 4 bolts and rear engine mounting insulator.


Hide 33030 21.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY

CAUTION:

The manual transmission unit assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.


a.
C332411

Remove the 7 bolts, transmission breather bracket from the manual transmission unit assembly.


b.

Operate the transmission jack and slowly remove the manual transmission unit assembly from the vehicle.

NOTICE:

Make sure that the manual transmission unit assembly is clear of all wiring and hoses.



Hide 33019C 22.REMOVE TRANSMISSION BREATHER SUB-ASSEMBLY

a.
C338148

Disconnect the 3 clamps and remove the transmission breather sub-assembly.


Hide 23.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C332413

Remove the bolt and wire harness clamp bracket from the manual transmission unit assembly.


Hide 36100 24.REMOVE TRANSFER ASSEMBLY