Home › Vehicle Interior › SEAT › FRONT SEATBACK HEATER
RM3250E _58 Vehicle Interior _038071 SEAT _0185776 FRONT SEATBACK HEATER A

SEAT  FRONT SEATBACK HEATER  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·
B394717

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.

·

If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

·

Replace any other damaged parts as necessary.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 71073S 1.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

a.

for Basic Style:

i.
B413333N01
1.969,1.365 2.917,1.115 true 2.333,2.969 2.885,3.021 true 2.313,3.198 2.896,3.021 true 2.99,1.021 3.146,1.219 0.156,0.198 10 true A 2.958,2.938 3.115,3.135 0.156,0.198 10 true B

Install the seat cover wire.

HINT:
·

There are service parts available for wires of 1000 mm or longer and formed wires.


·

When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm supplied wire into the dimensions shown in the illustration.


·

Refer to the precautions when creating a wire.



Length:
A 290 mm (11.42 in.)
B 420 mm (1.38 ft.)


HINT:
B376752

The dimensions shown in the illustration are the length.



ii.

Install the separate type front seatback cover.

HINT:
·

Refer to the precautions on wrinkles to avoid creating any on the separate type front seatback cover when installing the seat cover.


·

As shown in the illustration, fix all of the cover seam allowances in the same direction.

B394023N01
0.542,0.354 0.698,0.552 0.156,0.198 10 false A 0.813,0.458 0.969,0.656 0.156,0.198 10 false A 1.177,0.583 1.333,0.781 0.156,0.198 10 false B 1.5,0.719 1.656,0.917 0.156,0.198 10 true B 1.125,0.052 1.281,0.25 0.156,0.198 10 false C 0.813,0.24 0.969,0.438 0.156,0.198 10 true C 2.042,0.229 2.813,0.427 0.771,0.198 10 false A - A 3.438,0.24 4.208,0.438 0.771,0.198 10 false C - C 5.615,0.281 6.385,0.479 0.771,0.198 10 false B - B




iii.

Set the separate type front seatback cover.


iv.

Using hog ring pliers, install the separate type front seatback cover with 6 new hog rings in the order shown in the illustration.

HINT:
·

Do not dirty or damage the separate type front seatback cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.


B409606C01
5.25,2.229 5.24,1.646 true 5.094,0.948 4.958,0.938 true 3.417,0.427 3.063,0.719 true 1.74,0.302 2,0.563 true 1.563,0.802 1.979,1.188 true 1.563,0.792 2.271,1.156 true 2.75,1.219 3.365,1.146 true 2.927,1.375 3.365,1.156 true 5.115,0.854 5.427,1.052 0.313,0.198 10 false *a 5.198,2.281 5.51,2.479 0.313,0.198 10 false *1 3.417,0.229 3.875,0.427 0.458,0.198 10 false (1) 1.563,0.135 2.021,0.333 0.458,0.198 10 false (1) 1.365,0.677 1.823,0.875 0.458,0.198 10 false (2) 3.417,1.052 3.875,1.25 0.458,0.198 10 false (2)
*1 Hog Ring Pliers - -
*a Cutout - -





b.

for High Style:

i.
B413213N01
2.365,1.094 3.031,0.896 true 0.792,0.49 1.375,0.802 true 1.76,1.333 1.885,1.021 true 2.313,3.208 2.854,2.958 true 2.323,3.031 2.844,2.958 true 0.625,0.396 0.781,0.594 0.156,0.198 10 false A 3.125,0.771 3.281,0.969 0.156,0.198 10 false A 1.833,0.844 1.99,1.042 0.156,0.198 10 true B 2.958,2.865 3.115,3.063 0.156,0.198 10 false C

Install the seat cover wire.

HINT:
·

There are service parts available for wires of 1000 mm or longer and formed wires.


·

When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm supplied wire into the dimensions shown in the illustration.


·

Refer to the precautions when creating a wire.



Length:
A 170 mm (6.70 in.)
B 290 mm (11.42 in.)
C 420 mm (1.38 ft.)


HINT:
B376752

The dimensions shown in the illustration are the length.



ii.

Install the separate type front seatback cover.

HINT:
·

Refer to the precautions on wrinkles to avoid creating any on the separate type front seatback cover when installing the seat cover.


·

As shown in the illustration, fix all of the cover seam allowances in the same direction.

B394023N01
0.542,0.354 0.698,0.552 0.156,0.198 10 false A 0.813,0.458 0.969,0.656 0.156,0.198 10 false A 1.177,0.583 1.333,0.781 0.156,0.198 10 false B 1.5,0.719 1.656,0.917 0.156,0.198 10 true B 1.125,0.052 1.281,0.25 0.156,0.198 10 false C 0.813,0.24 0.969,0.438 0.156,0.198 10 true C 2.042,0.229 2.813,0.427 0.771,0.198 10 false A - A 3.438,0.24 4.208,0.438 0.771,0.198 10 false C - C 5.615,0.281 6.385,0.479 0.771,0.198 10 false B - B




iii.

Set the separate type front seatback cover.


iv.

Using hog ring pliers, install the separate type front seatback cover with 12 new hog rings in the order shown in the illustration.

HINT:
·

Do not dirty or damage the separate type front seatback cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.


B413336C01
5.375,2.24 5.344,1.667 true 5.094,0.917 4.969,0.938 true 3.604,1.052 2.958,1.146 true 3.615,1.073 3.063,0.74 true 1.979,0.604 1.333,0.698 true 2,1.031 1.344,0.698 true 2.333,1.156 2.677,0.26 true 2.646,1.25 2.667,0.271 true 3.531,2.292 2.729,2.438 true 3.531,2.292 2.781,2.188 true 3.542,2.313 2.896,1.521 true 1,1.75 1.938,1.333 true 0.979,1.75 1.792,1.927 true 1.021,1.76 1.74,2.26 true 5.313,2.292 5.625,2.49 0.313,0.198 10 false *1 5.104,0.833 5.417,1.031 0.313,0.198 10 false *a 3.698,1.021 4.156,1.219 0.458,0.198 10 false (1) 1.115,0.615 1.573,0.813 0.458,0.198 10 false (1) 2.604,0.073 3.063,0.271 0.458,0.198 10 false (2) 0.76,1.656 1.219,1.854 0.458,0.198 10 false (3) 3.646,2.25 4.104,2.448 0.458,0.198 10 false (3)
*1 Hog Ring Pliers - -
*a Cutout - -





Hide 71931 3.INSTALL FRONT SEAT HEADREST SUPPORT

Hide 71759C 4.INSTALL FRONT NO. 1 SEATBACK HOOK (w/ Front No. 1 Seatback Hook)

Hide 71014S 5.INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY LH

Hide 71862 7.INSTALL FRONT SEAT INNER CUSHION SHIELD LH

Hide 71812D 8.INSTALL FRONT SEAT CUSHION SHIELD LH

Hide 71868A 9.INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD LH (for Power Seat)

Hide 84921K 10.INSTALL POWER SEAT SWITCH KNOB LH (for Reclining, for Power Seat)

Hide 84921D 11.INSTALL POWER SEAT SWITCH KNOB LH (for Slide and Vertical, Lifter, for Power Seat)

Hide 72495 12.INSTALL VERTICAL ADJUSTING HANDLE LH (for Manual Seat)

Hide 72526E 13.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH (for Manual Seat)

a.
B413256C01
0,0 0,0 false
V113147

Install in this Direction


With the reclining adjuster release handle LH pulled up.


b.

Push in the installation direction shown in the illustration and attach the claw to install the reclining adjuster release handle LH.


Hide 71910A 14.INSTALL FRONT SEAT HEADREST ASSEMBLY