Home › Vehicle Interior › SEAT › FRONT SEAT CUSHION HEATER
RM3250E _58 Vehicle Interior _038071 SEAT _0185777 FRONT SEAT CUSHION HEATER A

SEAT  FRONT SEAT CUSHION HEATER  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·
B394717

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.

·

If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

·

Replace any other damaged parts as necessary.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 71071S 1.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

a.
B403869N01
1.708,0.573 2.083,0.302 true 1.708,0.563 1.323,0.292 true 0.833,0.781 0.49,0.667 true 0.698,2.469 0.354,2.354 true 2.948,0.708 2.615,0.854 true 3.094,2.354 2.76,2.5 true 1.646,1.271 1.646,1.573 true 1.667,2.26 1.667,2.563 true 1.635,0.625 1.802,0.823 0.167,0.198 10 true A 1.583,1.604 1.75,1.802 0.167,0.198 10 true C 1.604,2.615 1.771,2.813 0.167,0.198 10 true D 3.031,0.594 3.198,0.792 0.167,0.198 10 true B 0.302,0.573 0.469,0.771 0.167,0.198 10 true B 0.115,2.25 0.281,2.448 0.167,0.198 10 true E 3.156,2.271 3.323,2.469 0.167,0.198 10 true E

Install the seat cover wire.

HINT:
·

There are service parts available for wires of 1000 mm or longer and formed wires.


·

Refer to the precautions when creating a wire.



Length:
A 170 mm (6.70 in.)
B 150 mm (5.91 in.)
C 230 mm (9.06 in.)
D 270 mm (10.63 in.)
E 290 mm (11.42 in.)


HINT:
·
B376752

The dimensions shown in the illustration are the length.


·

Refer to the precautions on wrinkles to avoid creating any on the separate type front seat cushion cover when installing the seat cover.


·

As shown in the illustration, fix all of the cover seam allowances in the same direction.

B394024N10
2.5,0.24 3.271,0.438 0.771,0.198 10 false A - A 4.656,0.302 5.427,0.5 0.771,0.198 10 false B - B 0.198,0.396 0.354,0.594 0.156,0.198 10 false A 0.51,0.583 0.656,0.75 0.146,0.167 10 true A 0.938,0.802 1.094,1 0.156,0.198 10 false B 1.26,1.063 1.656,1.406 0.396,0.344 10 false B




b.

Temporarily install the separate type front seat cushion cover to the separate type front seat cushion pad.


c.

Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings in the order shown in the illustration.

B409602C01
5.25,2.177 5.323,1.667 false 4.969,0.927 5.115,0.938 true 5.115,0.844 5.427,1.042 0.313,0.198 10 false *a 5.167,2.229 5.479,2.427 0.313,0.198 10 false *1 1.99,1.771 2.208,1.979 0.219,0.208 10 true (1) 2.615,1.781 2.833,1.99 0.219,0.208 10 true (2) 1.979,1.156 2.198,1.365 0.219,0.208 10 true (3) 2.594,1.156 2.813,1.365 0.219,0.208 10 true (4) 1.365,1.844 1.635,2.052 0.271,0.208 10 true (10) 1.417,1.354 1.688,1.563 0.271,0.208 10 true (11) 1.448,1.104 1.729,1.313 0.281,0.208 10 true (12) 1.448,0.792 1.729,1 0.281,0.208 10 true (13) 1.49,0.51 1.75,0.719 0.26,0.208 10 true (14) 3.146,1.844 3.365,2.052 0.219,0.208 10 true (5) 3.135,1.365 3.354,1.573 0.219,0.208 10 true (6) 3.135,1.125 3.354,1.333 0.219,0.208 10 true (7) 3.125,0.833 3.344,1.042 0.219,0.208 10 true (8) 3.104,0.563 3.323,0.771 0.219,0.208 10 true (9) 1.802,0.177 2.073,0.385 0.271,0.208 10 true (18) 2.125,0.177 2.385,0.385 0.26,0.208 10 true (17) 2.427,0.177 2.688,0.385 0.26,0.208 10 true (16) 2.75,0.177 3.021,0.417 0.271,0.24 10 true (15)
*1 Hog Ring Pliers - -
*a Cutout - -



d.

Using hog ring pliers, connect the 2 straps of the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

HINT:
·

Do not dirty or damage the separate type front seatback cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.



B413228C01
4.927,2.083 5.156,1.563 false 4.771,2.125 5.083,2.323 0.313,0.198 10 false *1
*1 Hog Ring Pliers - -



Hide 2.INSTALL SEAT CUSHION COVER WITH PAD

Hide 71014S 3.INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY LH

Hide 71862 5.INSTALL FRONT SEAT INNER CUSHION SHIELD LH

Hide 71812D 6.INSTALL FRONT SEAT CUSHION SHIELD LH

Hide 71868A 7.INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD LH (for Power Seat)

Hide 84921K 8.INSTALL POWER SEAT SWITCH KNOB LH (for Reclining, for Power Seat)

Hide 84921D 9.INSTALL POWER SEAT SWITCH KNOB LH (for Slide and Vertical, Lifter, for Power Seat)

Hide 72495 10.INSTALL VERTICAL ADJUSTING HANDLE LH (for Manual Seat)

Hide 72526E 11.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH (for Manual Seat)

a.
B413256C01
0,0 0,0 false
V113147

Install in this Direction


With the reclining adjuster release handle LH pulled up.


b.

Push in the installation direction shown in the illustration and attach the claw to install the reclining adjuster release handle LH.


Hide 71910A 12.INSTALL FRONT SEAT HEADREST ASSEMBLY