Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY › 2015.06–2016.08
RM3250E _52 Drivetrain _038039 AXLE AND DIFFERENTIAL _0186172 FRONT DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL FRONT DIFFERENTIAL SIDE GEAR SHAFT BEARING RH

a.
C237648N02
2.504,0.649 2.819,0.81 0.315,0.161 10 SST 1.913,0.73 2.471,0.73 false

Using SST and a press, press in the front differential side gear shaft bearing RH.

SST
09223-00010  


b.

Using a snap ring expander, install the snap ring.

HINT:

Install the snap ring securely.



Hide 41304F 2.INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH

a.
C237490

Install the differential side gear shaft sub-assembly RH to the front differential tube assembly.


b.

Using a snap ring pliers, install a new snap ring.

HINT:

Install the snap ring securely.



Hide 41304P 3.INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL RH

Hide 41434 4.INSTALL DIFFERENTIAL CLUTCH HUB (w/ A.D.D.)

a.
C237649

Install the differential clutch hub to the differential side gear shaft sub-assembly RH.


b.

Using snap ring expander, install the side gear shaft hole snap ring.

HINT:

Install the snap ring securely.


NOTICE:

Make sure to install the differential clutch hub in the correct direction.



Hide 41331G 5.INSTALL FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING

a.
C237650C01
1.063,0.688 0.74,0.469 0.74,0.469 0.51,0.469 false 0.156,0.385 0.458,0.531 0.302,0.146 10 false SST 2.833,0.271 3.146,0.469 0.313,0.198 10 false *a
*a Front Differential Side Gear Needle Roller Bearing Depth


Using SST and a press, press in 2 new front differential side gear needle roller bearings.

SST
09950-60010  (09951-00380)

Front differential side gear needle roller bearing depth:

1.4 to 2.0 mm (0.0552 to 0.0787 in.)



Hide 6.ASSEMBLE DIFFERENTIAL CASE

a.
C236671

Install 2 thrust washers to the 2 differential side gears.

HINT:

Using the table below, select 2 differential side gear thrust washers which will ensure that the backlash is within the specifications.


Standard Thrust Washer Thickness:
Thickness mm (in.) Thickness mm (in.)
1.48 to 1.52 (0.0583 to 0.0598) 1.73 to 1.77 (0.0682 to 0.0696)
1.53 to 1.57 (0.0603 to 0.0618) 1.78 to 1.82 (0.0701 to 0.0716)
1.58 to 1.62 (0.0622 to 0.0637) 1.83 to 1.87 (0.0721 to 0.0736)
1.63 to 1.67 (0.0642 to 0.0657) 1.88 to 1.92 (0.0741 to 0.0755)
1.68 to 1.72 (0.0662 to 0.0677) -



b.
C236669

Install the 2 differential side gears, 2 differential pinion gears, 2 differential side gear thrust washers, 2 differential pinion gear thrust washers and differential pinion shaft to the differential case.

HINT:

Align the holes of the differential case and differential pinion shaft.



c.
C236672

Measure the side gear backlash.

i.

Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case.

Side gear backlash:

0.15 mm (0.00590 in.) or less


If the backlash is not as specified, install 2 differential side gear thrust washers with different thicknesses.




d.
C236668

Using a pin punch and hammer, tap in the straight pin through the differential case and hole of the differential pinion shaft.


e.

Stake the differential case.


Hide 7.INSTALL DIFFERENTIAL RING GEAR

a.

Clean the contact surface of the differential case and differential ring gear.


b.

Heat the differential ring gear in boiling water that is approximately 100°C (212°F).


c.

Carefully remove the differential ring gear from the boiling water.


d.

After the moisture on the differential ring gear has completely evaporated, quickly install the differential ring gear to the differential case.


e.
C326819C01
1.927,1.135 2.771,1.135 true 1.906,1.031 2.323,1.031 2.323,1.031 2.323,1.135 true 2.844,1.042 3.156,1.24 0.313,0.198 10 true *a
*a Matchmark


Align the matchmarks on the differential ring gear and differential case.


f.

After the ring gear cools down, apply thread lock adhesive to the 10 set bolts and install them.

Thread lock:

Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent


Torque:
96.5 N*m (984 kgf*cm, 71 ft.*lbf)


Hide 41311A 8.INSTALL FRONT DIFFERENTIAL CASE BEARING

a.
C237495N02
0.906,0.448 0.438,0.448 false 0.813,0.75 0.604,0.75 0.604,0.75 0.604,0.448 false 2.438,1.729 2.99,1.729 true 0.094,0.375 0.396,0.531 0.302,0.156 10 false SST 3.01,1.646 3.313,1.802 0.302,0.156 10 false SST

Using SST and a press, press the 2 front differential case bearings (inner) onto the differential case.

SST
09950-60010  (09951-00520, 09951-00610)
09950-70010  (09951-07150)


Hide 41311A 9.INSTALL FRONT DIFFERENTIAL CASE BEARING

HINT:

When replacing the 2 front differential case bearings, install the thinnest washer to each front differential case bearing. When reusing the front differential case bearings, install a new plate washer of the same thickness as the one that was removed to each front differential case bearing.


a.
C237496N02
1.125,0.99 1.292,0.156 1.292,0.156 1.51,0.156 true 1.542,0.083 1.854,0.24 0.313,0.156 10 false SST

Using SST and a press, press in the front differential case bearing (outer) to the differential side bearing retainer.

SST
09950-60020  (09951-00810)
09950-70010  (09951-07150)


b.
C237497N02
1.313,1.083 1.938,0.146 1.938,0.146 2.083,0.146 true 2.135,0.073 2.865,0.375 0.729,0.302 10 false SST

Using SST and a press, press in the front differential case bearing (outer) to the differential carrier.

SST
09950-60020  (09951-00810)
09950-70010  (09951-07150)


Hide 41211A 10.INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C326826C01
0.927,3.208 1.469,3.208 true 1.969,3.063 2.635,3.063 true 1.938,3.635 2.479,3.635 true 2.448,0.688 2.76,0.885 0.313,0.198 10 false *a 0.302,2.031 0.615,2.229 0.313,0.198 10 false *b 0.75,3.135 1.063,3.333 0.313,0.198 10 false *1 2.698,2.99 3.156,3.188 0.458,0.198 10 false SST 2.531,3.563 2.99,3.76 0.458,0.198 10 false SST
*1 Front Drive Pinion Front Tapered Roller Bearing (Outer)
*a Turn
*b Hold


Using SST, install the front drive pinion front tapered roller bearing (outer).

SST
09950-60020  (09951-00720, 09951-00890)


Hide 41211B 11.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.

Using a brass bar and hammer, tap in a new front differential oil storage ring.


b.
C327401C01
0.771,3.594 1.458,3.594 true 1.958,3.021 2.427,3.021 true 1.917,3.688 2.49,3.688 true 2.479,0.677 2.792,0.875 0.313,0.198 10 false *a 0.375,2.031 0.688,2.229 0.313,0.198 10 false *b 0.583,3.51 0.896,3.708 0.313,0.198 10 false *1 2.49,2.938 2.948,3.135 0.458,0.198 10 false SST 2.542,3.604 3,3.802 0.458,0.198 10 false SST
*1 Front Drive Pinion Rear Tapered Roller Bearing (Outer)
*a Turn
*b Hold


Using SST, install the front drive pinion rear tapered roller bearing (outer).

SST
09950-60020  (09951-00720, 09951-00890)


Hide 41211A 12.INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

a.

Install the drive pinion plate washer to the differential drive pinion.

HINT:

First, install a drive pinion plate washer that has the same thickness as the removed drive pinion plate washer. After checking the tooth contact pattern, replace the drive pinion plate washer with one of a different thickness if necessary.



b.
C236679N06
1.885,1.365 2.344,0.875 2.344,0.875 2.469,0.875 true 2.51,0.802 2.865,1.042 0.354,0.24 10 false SST

Using SST and a press, press the front drive pinion front tapered roller bearing (inner) onto the differential drive pinion.

SST
09506-30012  


Hide 13.ADJUST DIFFERENTIAL DRIVE PINION PRELOAD

a.
C237303

Install the differential drive pinion, front drive pinion rear tapered roller bearing (inner) and front differential drive pinion oil slinger.

HINT:

Install the front differential drive pinion bearing spacer and front differential carrier oil seal after adjusting the gear contact pattern.



b.
C237304C05
1.447,0.703 1.014,0.703 false 0.669,0.602 0.978,0.753 0.309,0.152 10 SST 2.736,1.239 2.901,1.4 0.166,0.161 10 *a 0.41,1.6 0.575,1.761 0.166,0.161 10 *b
*a Turn
*b Hold


Using SST, install the front drive pinion companion flange sub-assembly with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



c.

Adjust the differential drive pinion preload by tightening the front drive pinion companion flange nut.


d.
C282254C04
0.573,0.594 0.896,0.594 false 3.052,1.115 3.365,1.313 0.313,0.198 10 false *a 0.281,1.063 0.594,1.26 0.313,0.198 10 false *b 0.281,0.51 0.594,0.708 0.313,0.198 10 false SST
*a Turn
*b Hold


Using SST to hold the front drive pinion companion flange sub-assembly with dust deflector in place, tighten the front drive pinion companion flange nut.

SST
09330-00021  (09330-00030)

Limit torque value:

370 N*m (3773 kgf*cm, 273 ft.*lbf) or less


NOTICE:
·

As there is no spacer, tighten the nut a little at a time. Be careful not to overtighten it.

·

Apply hypoid gear oil LSD to the drive pinion thread and nut seat face.




e.
C237317

Using a torque wrench, measure the preload.

Standard Preload (Starting Torque):
Item Specified Condition
New bearing 0.98 to 1.92 N*m (10 to 19 kgf*cm, 9 to 16 in.*lbf)
Reused bearing 0.97 to 1.81 N*m (10 to 18 kgf*cm, 9 to 16 in.*lbf)


NOTICE:
·

For a more accurate measurement, rotate the bearing forward and backward several times before measuring.

·

Record the differential drive pinion preload for the total preload measurement.




Hide 14.INSTALL DIFFERENTIAL CASE ASSEMBLY

Hide 15.ADJUST DIFFERENTIAL RING GEAR BACKLASH

a.

Install the side bearing retainer with the 10 bolts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


b.
C237478N05
1.385,1.313 0.75,0.854 0.75,0.854 0.563,0.854 true 0.208,0.802 0.708,1.063 0.5,0.26 10 false SST

Using SST and a dial indicator, measure the ring gear backlash.

SST
09564-33010  

Standard backlash:

0.11 to 0.21 mm (0.00433 to 0.00826 in.)


If the backlash is not as specified, adjust it by either increasing or decreasing the number of washers on both sides equally.

HINT:

There should be no clearance between the plate washer and case. Make sure that the ring gear has backlash.


Standard Washer LH Thickness (Side Opposite Ring Gear):
Part No. Thickness mm (in.) Part No. Thickness mm (in.)
90564-50184 1.57 to 1.59 (0.0619 to 0.0625) 90564-50194 1.87 to 1.89 (0.0737 to 0.0744)
90564-50124 1.59 to 1.61 (0.0626 to 0.0633) 90564-50134 1.89 to 1.91 (0.0744 to 0.0751)
90564-50185 1.61 to 1.63 (0.0634 to 0.0641) 90564-50195 1.91 to 1.93 (0.0752 to 0.0759)
90564-50186 1.63 to 1.65 (0.0642 to 0.0649) 90564-50196 1.93 to 1.95 (0.0760 to 0.0767)
90564-50126 1.65 to 1.67 (0.0650 to 0.0657) 90564-50136 1.95 to 1.97 (0.0768 to 0.0775)
90564-50187 1.67 to 1.69 (0.0658 to 0.0665) 90564-50197 1.97 to 1.99 (0.0776 to 0.0783)
90564-50188 1.69 to 1.71 (0.0666 to 0.0673) 90564-50198 1.99 to 2.01 (0.0784 to 0.0791)
90564-50128 1.71 to 1.73 (0.0674 to 0.0681) 90564-50138 2.01 to 2.03 (0.0792 to 0.0799)
90564-50189 1.73 to 1.75 (0.0682 to 0.0688) 90564-50199 2.03 to 2.05 (0.0800 to 0.0807)
90564-50190 1.75 to 1.77 (0.0689 to 0.0696) 90564-50200 2.05 to 2.07 (0.0808 to 0.0814)
90564-50130 1.77 to 1.79 (0.0697 to 0.0704) 90564-50140 2.07 to 2.09 (0.0815 to 0.0822)
90564-50191 1.79 to 1.81 (0.0705 to 0.0712) 90564-50201 2.09 to 2.11 (0.0823 to 0.0830)
90564-50192 1.81 to 1.83 (0.0713 to 0.0720) 90564-50202 2.11 to 2.13 (0.0831 to 0.0838)
90564-50132 1.83 to 1.85 (0.0721 to 0.0728) 90564-50142 2.13 to 2.15 (0.0839 to 0.0846)
90564-50193 1.85 to 1.87 (0.0729 to 0.0736) 90564-50203 2.15 to 2.17 (0.0847 to 0.0854)


Standard Washer RH Thickness (ring gear side):
Part No. Thickness mm (in.) Part No. Thickness mm (in.)
90564-50204 1.57 to 1.59 (0.0619 to 0.0625) 90564-50214 1.87 to 1.89 (0.0737 to 0.0744)
90564-50154 1.59 to 1.61 (0.0626 to 0.0633) 90564-50164 1.89 to 1.91 (0.0744 to 0.0751)
90564-50205 1.61 to 1.63 (0.0634 to 0.0641) 90564-50215 1.91 to 1.93 (0.0752 to 0.0759)
90564-50206 1.63 to 1.65 (0.0642 to 0.0649) 90564-50216 1.93 to 1.95 (0.0760 to 0.0767)
90564-50156 1.65 to 1.67 (0.0650 to 0.0657) 90564-50166 1.95 to 1.97 (0.0768 to 0.0775)
90564-50207 1.67 to 1.69 (0.0658 to 0.0665) 90564-50217 1.97 to 1.99 (0.0776 to 0.0783)
90564-50208 1.69 to 1.71 (0.0666 to 0.0673) 90564-50218 1.99 to 2.01 (0.0784 to 0.0791)
90564-50158 1.71 to 1.73 (0.0674 to 0.0681) 90564-50168 2.01 to 2.03 (0.0792 to 0.0799)
90564-50209 1.73 to 1.75 (0.0682 to 0.0688) 90564-50219 2.03 to 2.05 (0.0800 to 0.0807)
90564-50210 1.75 to 1.77 (0.0689 to 0.0696) 90564-50220 2.05 to 2.07 (0.0808 to 0.0814)
90564-50160 1.77 to 1.79 (0.0697 to 0.0704) 90564-50170 2.07 to 2.09 (0.0815 to 0.0822)
90564-50211 1.79 to 1.81 (0.0705 to 0.0712) 90564-50221 2.09 to 2.11 (0.0823 to 0.0830)
90564-50212 1.81 to 1.83 (0.0713 to 0.0720) 90564-50222 2.11 to 2.13 (0.0831 to 0.0838)
90564-50162 1.83 to 1.85 (0.0721 to 0.0728) 90564-50172 2.13 to 2.15 (0.0839 to 0.0846)
90564-50213 1.85 to 1.87 (0.0729 to 0.0736) 90564-50223 2.15 to 2.17 (0.0847 to 0.0854)




Hide 16.INSPECT TOTAL PRELOAD

a.
C237317

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard Total Preload (Starting Torque):
Item Specified Condition
New bearing 1.2 to 2.8 N*m (13 to 28 kgf*cm, 11 to 24 in.*lbf)
Reused bearing 1.19 to 2.69 N*m (13 to 27 kgf*cm, 11 to 23 in.*lbf)


NOTICE:

Record the differential ring gear preload.



Hide 17.ADJUST TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

a.

Remove the differential case bearing retainer and differential case.


b.
C237500

Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.


c.

Install the differential case and differential case bearing retainer.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


d.

Hold the companion flange firmly in place and rotate the ring gear in both directions.


e.

Remove the differential case bearing retainer and differential case.


f.

Inspect the tooth contact pattern.

C205651C01
0.271,1.188 0.604,1.406 0.333,0.219 10 false *a 2.01,0.333 2.708,0.5 0.698,0.167 12 false *A 2.938,0.792 3.313,1.01 0.375,0.219 10 false *b 5.49,0.792 5.823,1.052 0.333,0.26 10 false *c 4.354,1.656 4.667,1.896 0.313,0.24 10 false *d 2.927,2.719 3.177,2.958 0.25,0.24 10 false *e 5.552,2.76 5.802,3.021 0.25,0.26 10 false *f 4.385,3.552 4.656,3.833 0.271,0.281 10 false *g 2.031,4.604 2.74,4.792 0.708,0.188 12 false *B 2.969,5.094 3.271,5.354 0.302,0.26 10 false *h 5.552,5.198 5.792,5.417 0.24,0.219 10 false *i 3.01,6.958 3.292,7.198 0.281,0.24 10 false *j 5.552,7.125 5.844,7.375 0.292,0.25 10 false *k 4.385,5.938 4.677,6.229 0.292,0.292 10 false *d 4.385,7.771 4.646,8.052 0.26,0.281 10 false *g
*A Drive Side *B Coast Side
*a Proper Contact *b Toe Contact
*c Face Contact *d Select an adjusting washer that will shift the drive pinion closer to the ring gear.
*e Heel Contact *f Flank Contact
*g Select an adjusting washer that will shift the drive pinion away from the ring gear. *h Heel Contact
*i Flank Contact *j Toe Contact
*k Face Contact - -



g.
C237312C05
2.111,1.755 2.274,1.906 0.163,0.152 10 *1 1.738,1.45 1.738,1.84 1.738,1.84 2.08,1.84 false
*1 Drive Pinion Water


If the teeth are not contacting properly, use the following chart to select a proper washer.

Standard Washer Thickness:
Part No. Thickness mm (in.) Part No. Thickness mm (in.)
90564-35109 1.69 to 1.71 (0.0666 to 0.0673) 90564-35120 2.02 to 2.04 (0.0796 to 0.0803)
90564-35110 1.72 to 1.74 (0.0678 to 0.0685) 90564-35121 2.05 to 2.07 (0.0807 to 0.0814)
90564-35111 1.75 to 1.77 (0.0689 to 0.0696) 90564-35123 2.08 to 2.10 (0.0819 to 0.0826)
90564-35112 1.78 to 1.80 (0.0701 to 0.0708) 90564-35124 2.11 to 2.13 (0.0831 to 0.0838)
90564-35113 1.81 to 1.83 (0.0713 to 0.0720) 90564-35125 2.14 to 2.16 (0.0843 to 0.0850)
90564-35114 1.84 to 1.86 (0.0725 to 0.0732) 90564-35126 2.17 to 2.19 (0.0855 to 0.0862)
90564-35115 1.87 to 1.89 (0.0737 to 0.0744) 90564-35127 2.20 to 2.22 (0.0867 to 0.0874)
90564-35116 1.90 to 1.92 (0.0748 to 0.0755) 90564-35128 2.23 to 2.25 (0.0878 to 0.0885)
90564-35117 1.93 to 1.95 (0.0760 to 0.0767) 90564-36129 2.26 to 2.28 (0.0890 to 0.0897)
90564-35118 1.96 to 1.98 (0.0772 to 0.0779) 90564-35130 2.29 to 2.31 (0.0902 to 0.0909)
90564-35119 1.99 to 2.01 (0.0784 to 0.0791) 90564-35131 2.32 to 2.34 (0.0914 to 0.0921)



Hide 41204D 18.REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT

Hide 41204D 19.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 41214C 20.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41211B 21.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

Hide 22.REMOVE DIFFERENTIAL DRIVE PINION

Hide 41231F 23.INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C238723

Install a new front differential drive pinion bearing spacer to the differential drive pinion.


Hide 24.INSTALL DIFFERENTIAL DRIVE PINION

Hide 41211B 25.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C237314

Install the front drive pinion rear tapered roller bearing (inner) to the differential drive pinion.


Hide 41214C 26.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 27.INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL

Hide 41204D 28.INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 29.INSTALL FRONT DIFFERENTIAL UNION

a.

Install the front differential union to the differential side bearing retainer.


Hide 30.INSTALL DIFFERENTIAL SIDE BEARING RETAINER

a.

Remove any old seal packing material from the differential side bearing retainer.

NOTICE:

Do not drop oil on the contact surfaces of the differential carrier and differential side bearing retainer.



b.

Clean residual seal packing material on the contact surface using gasoline or alcohol.


c.
C237503C04
2.406,0.573 2.771,0.219 2.771,0.219 2.885,0.219 true 2.938,0.135 3.188,0.323 0.25,0.188 10 false *a
*a Seal Packing


Apply seal packing to the differential side bearing retainer as shown in the illustration.

Seal packing:

Toyota Genuine seal packing 1281, Three Bond 1281 or equivalent


HINT:

Install the differential side bearing retainer within 3 minutes after applying seal packing.



d.

Install the differential side bearing retainer with the 10 bolts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 31.INSPECT TOTAL PRELOAD

a.
C237317

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard Preload (Starting Torque):
Item Specified Condition
New bearing 1.3 to 2.9 N*m (14 to 29 kgf*cm, 12 to 25 in.*lbf)
Reused bearing 1.29 to 2.79 N*m (14 to 28 kgf*cm, 12 to 24 in.*lbf)


If necessary, disassemble and inspect the differential.



Hide 32.INSPECT DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH

a.
C237478N06
1.385,1.313 0.75,0.854 0.75,0.854 0.563,0.854 true 0.208,0.771 0.51,0.927 0.302,0.156 10 false SST

Using SST and a dial indicator, measure the ring gear backlash.

SST
09564-32011  

Standard backlash:

0.11 to 0.21 mm (0.00433 to 0.00826 in.)


If the backlash is not within the specification, adjust the side bearing preload.



Hide 41204D 33.INSPECT FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

Hide 41304P 35.INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL LH

Hide 41183B 36.INSTALL FRONT DIFFERENTIAL SIDE BEARING RETAINER DEFLECTOR

a.
C237651

Using a brass bar and hammer, tap in the front differential side bearing retainer deflector.

NOTICE:

Make sure to install the front differential side bearing retainer deflector in the correct direction.



Hide 41306F 37.INSTALL DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY (w/ A.D.D.)

a.

Install a new side gear intermediate shaft hole snap ring to the differential side gear inter shaft sub-assembly.


b.
C237652

Using a plastic-faced hammer, tap the differential side gear inter shaft sub-assembly into the differential case.


c.

Check that there is 2 to 3 mm (0.0788 to 0.118 in.) of axial play.


d.

Check that the differential side gear inter shaft sub-assembly cannot be completely pulled out by hand.


Hide 41433 38.INSTALL DIFFERENTIAL CLUTCH SLEEVE (w/ A.D.D.)

a.

Install the differential clutch sleeve.


Hide 41320 39.INSTALL FRONT DIFFERENTIAL TUBE ASSEMBLY

a.

Remove any old seal packing material on the contact surfaces of the differential and clutch case.

NOTICE:

Do not drop oil on the contact surfaces of the differential and clutch case.



b.

Clean residual seal packing material on the contact surface using gasoline or alcohol.


c.
C237504C04
1.635,1.469 0.948,1.781 0.948,1.781 0.792,1.781 true 0.615,1.698 0.938,1.927 0.323,0.229 10 false *a
*a Seal Packing


Apply seal packing to the differential as shown in the illustration.

Seal packing:

Toyota Genuine seal packing 1281, Three Bond 1281 or equivalent


HINT:

Install the differential tube within 3 minutes after applying seal packing.



d.

Install the front differential tube to the differential.


e.
C237653

w/ A.D.D.

i.

Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.


ii.

Using an E14 ''TORX'' socket wrench, install the 4 bolts.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)



f.
C237479

w/o A.D.D.

i.

Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.


ii.

Using an E14 ''TORX'' socket wrench, install the 4 bolts.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)



Hide 41400B 40.INSTALL DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY (w/ A.D.D.)

a.
C237514C02
1.094,0.813 1.625,0.292 1.625,0.292 2.052,0.292 true 2.125,0.198 2.438,0.396 0.313,0.198 10 false *a
*a Seal Packing


Remove any seal packing material from the contact surface of the differential and clutch case. Also, do not drop oil on the contact surfaces.


b.

Clean residual seal packing material from the contact surfaces using gasoline or alcohol.


c.

Apply seal packing to the front differential tube as shown.

Seal packing:

Toyota Genuine seal packing 1281, Three Bond 1281 or equivalent


HINT:

Install the actuator within 3 minutes after applying seal packing.



d.

Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.


e.
C327528

Install the differential motor actuator assembly to the front differential tube.


f.

Install the 4 bolts.

Torque:
20.6 N*m (210 kgf*cm, 15 ft.*lbf)


Hide 89429 41.INSTALL OIL TEMPERATURE SENSOR

a.
C326232

Install the oil temperature sensor to the front differential carrier assembly.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)