Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2015.06–2016.01
RM3250E _59 Vehicle Exterior _038077 DOOR / HATCH _0186366 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

Use the same procedure for RHD and LHD vehicles.

·

The procedures listed below are for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 75922M 2.INSTALL NO. 1 BLACK OUT TAPE LH (w/ Black Out Tape)

Hide 67862 3.INSTALL FRONT DOOR WEATHERSTRIP LH

a.
B412097

for Single Cab:

Attach the clip to install the front door weatherstrip LH.


b.
B412098

for Smart Cab:

i.

Attach the clip to install a new front door weatherstrip LH.


ii.

Remove the peeling paper from double-sided tape and press the double-sided tape to the front of the door panel.



c.
B412099

for Double Cab:

Attach the clip to install the front door weatherstrip LH.


Hide 68620 4.INSTALL FRONT DOOR CHECK ASSEMBLY LH

a.

Apply MP grease to the sliding area of the front door check assembly LH.


b.

When reusing a bolt:

i.

Clean the threads of the bolt with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt (B).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




c.
B412096C02
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)


Install the front door check assembly LH with the 2 bolts (A) and bolt (B).

Torque:
Bolt (A) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt (B) : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 67837B 5.INSTALL FRONT DOOR DUST PROOF SEAL

a.
B412094

Attach the claw to install 3 new front door dust proof seals.


Hide 67001A 6.INSTALL FRONT DOOR PANEL CUSHION

a.
B412095

Attach the claw to install 2 new front door panel cushions.


Hide 75720 7.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH

Hide 69312 8.INSTALL FRONT DOOR LOCK OPEN ROD LH

a.
B412100C01
0,0 0,0 false
V113147

Install in this Direction


Attach the snap to install the front door lock open rod LH to the front door outside handle frame sub-assembly LH as shown in the illustration.


Hide 69202A 9.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding area of the front door outside handle frame sub-assembly LH.


b.
B412092C02
2.135,1.552 2.313,1.552 2.313,1.552 2.313,1.208 false 0.76,0.885 1.083,0.885 true 1.677,1.26 1.51,1.26 1.51,1.26 1.51,1.042 false 1.698,1.177 1.896,1.406 0.198,0.229 10 true *b 0.625,0.771 0.823,1 0.198,0.229 10 true *a 2,1.438 2.198,1.667 0.198,0.229 10 true *a
*a Clamp
*b Guide


Attach the guide and clamp to connect the wire harness.


c.
B412101C01
2.167,0.729 2.167,0.344 2.167,0.344 2.438,0.344 true 1.219,0.417 1.219,0.146 1.219,0.146 0.927,0.146 true 0.875,0.969 1.208,0.969 1.208,0.969 1.208,0.729 true 2.417,0.271 2.646,0.49 0.229,0.219 10 true *a 0.792,0.052 1.021,0.271 0.229,0.219 10 true *b 0.75,0.865 0.979,1.083 0.229,0.219 10 true *b
*a Grommet
*b Guide
V113147

Install in this Direction


Attach the grommet and guide to install the front door outside handle frame sub-assembly LH as shown in the illustration.


d.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242E 10.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B412102C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the front door rear outside handle pad.


Hide 69241H 11.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B412103C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the front door front outside handle pad.


Hide 69220 12.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B412104C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door outside handle assembly LH as shown in the illustration.


b.
B412105

Connect the connector.


c.
B412106C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to close the connector cover as shown in the illustration.


Hide 69318C 13.INSTALL DOOR LOCK WIRING HARNESS SEAL

Hide 69720B 14.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

Hide 69760C 15.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

Hide 69036A 16.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY LH

Hide 69320 17.INSTALL FRONT DOOR LOCK ASSEMBLY LH

Hide 69217D 18.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B412107C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and claw to install the front door outside handle cover to the lock cylinder assembly as shown in the illustration.


Hide 19.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.

Apply MP grease to the sliding area of the front door outside handle cover with lock cylinder assembly.


b.
B412108C01
2.323,1.958 2.854,1.958 true 2.156,1.875 2.385,2.083 0.229,0.208 10 true *1
*1 Hole Plug
V113147

Install in this Direction


Install the front door outside handle cover with lock cylinder assembly as shown in the illustration.

HINT:

Check that the front door lock cylinder assembly is inserted into the front door lock assembly LH.



c.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.

Install the hole plug.


Hide 69217D 20.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B412109C01
0.229,1.969 0.885,1.969 true 0.844,1.885 1.083,2.104 0.24,0.219 10 true *1
*1 Hole Plug
V113147

Install in this Direction


Attach the claw to install the front door outside handle cover as shown in the illustration.


b.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

Install the hole plug.


Hide 67404F 21.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B412081

Attach the guide to install the front door rear lower frame sub-assembly LH.


b.

Install the bolt.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 85720C 22.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Power Window)

Hide 69802 23.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding area of the front door window regulator sub-assembly LH.


b.

Temporarily install the temporarily bolt to the front door window regulator sub-assembly LH.


c.

w/ Power Window:

i.

Install the front door window regulator sub-assembly LH with the 5 bolts and temporarily bolt.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Temporarily Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


ii.

Connect the connector.



d.

w/o Power Window:

Install the front door window regulator sub-assembly LH with the 4 bolts and temporarily bolt.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Temporarily Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)

B412082C02
0.115,0.052 0.344,0.25 0.229,0.198 10 true *A 3.531,0.063 3.76,0.26 0.229,0.198 10 true *B
*A w/ Power Window *B w/o Power Window
V100135

Bolt
V100136

Connector
V100137

Temporarily Bolt - -



Hide 68102 24.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

w/ Power Window:

i.

Temporarily install the power window regulator master switch assembly.


ii.

Connect the cable to the negative (-) battery terminal.


iii.

Move the front door window regulator sub-assembly LH so that the front door glass sub-assembly LH bolts can be seen.


iv.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:
w/ Curtain Shield Airbag:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



v.

Remove the power window regulator master switch assembly.



b.
B412110C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Install the front door glass sub-assembly LH as shown in the illustration.

NOTICE:

Do not damage the front door glass sub-assembly LH.



c.
B412079

Install the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68151C 25.INSTALL FRONT DOOR GLASS RUN LH

a.
B412078

for Single Cab, Smart Cab:

Attach the guide to install the front door glass run LH.


b.
B412078

for Double Cab:

Attach the guide to install a new front door glass run LH.


Hide 26.INSTALL SCREW GROMMET

B412077

a.

Attach the claw to install 2 new screw grommets.


Hide 67832 27.INSTALL FRONT DOOR SERVICE HOLE COVER LH

a.

Apply new butyl tape to the front door panel.


b.
B412111C01
0.927,0.125 1.063,0.125 1.063,0.125 1.063,0.292 true 3.073,0.26 2.927,0.26 2.927,0.26 2.927,0.427 true 0.698,0.031 0.979,0.25 0.281,0.219 10 true *a 3.031,0.167 3.313,0.385 0.281,0.219 10 true *a
*a Reference Point


Pass the front door inside locking cable assembly LH and front door lock remote control cable assembly LH through a new front door service hole cover LH, and then attach the front door service hole cover LH using the reference points on the front door panel.

HINT:
·

Securely install the front door service hole cover LH to prevent wrinkles and air bubbles.

·

There should be no wrinkles or folds after installing the front door service hole cover LH.

·

After installing the front door service hole cover LH, check the seal quality.




c.

Attach the clamp.


d.

w/ Power Mirror Control System:

Attach the clamp.


e.

w/ Curtain Shield Airbag:

Install the ground wire with the ground bolt.


Hide 87940 28.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 89835 29.INSTALL DOOR SIDE AIR BAG SENSOR LH (w/ Curtain Shield Airbag)

Hide 86160P 30.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (w/ Front No. 2 Speaker)

Hide 86160 31.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 68172A 32.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.

Install a new front door inner glass weatherstrip LH to the front door trim board sub-assembly LH and fold down the claw in the directions indicated by the arrows in the illustration.

B412112C01
0.083,0.073 0.396,0.271 0.313,0.198 10 false *A 3.698,0.063 4.01,0.26 0.313,0.198 10 false *B
*A for Single Cab, Smart Cab *B for Double Cab



Hide 69206B 33.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B412113C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and guide to install the front door inside handle sub-assembly LH to the front door trim board sub-assembly LH.


Hide 67602 34.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B412114C01
1.719,0.344 1.99,0.344 1.99,0.344 2.521,0.917 true 1.76,1.885 2.125,1.885 2.125,1.885 2.531,1.375 true 1.531,0.24 1.792,0.448 0.26,0.208 10 true *1 1.573,1.76 1.833,1.969 0.26,0.208 10 true *2
*1 Front Door Inside Locking Cable Assembly LH
*2 Front Door Lock Remote Control Cable Assembly LH
V113147

Install in this Direction


Attach the clamp to connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH as shown in the illustration.


b.
B412115C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide as shown in the illustration.


c.

Attach the clip to install the front door trim board sub-assembly LH.

B412116C01
0.135,0.094 0.448,0.292 0.313,0.198 10 true *A 3.938,0.115 4.25,0.313 0.313,0.198 10 true *B
*A for Single Cab, Smart Cab *B for Double Cab



d.
B412070

Install the 3 screws.


Hide 69284C 35.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

a.
B412117

Attach the claw to install the front door inside handle bezel plug LH as shown in the illustration.


Hide 67666B 36.INSTALL FRONT DOOR TRIM REFLECTOR LH (w/ Reflex Reflector Assembly)

a.
B412118C01
0.094,0.083 0.406,0.281 0.313,0.198 10 true *A 0.115,2.542 0.427,2.74 0.313,0.198 10 true *B
*A for LH Side
*B for RH Side
V100155

Protective Tape
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Attach the guide and claw to install the front door trim reflector LH as shown in the illustration.


b.

Remove the protective tape.


Hide 84820 37.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side, w/ Power Window)

a.

for Models with Jam Protection Function on Driver Door Window Only:

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSTALLATION


b.

except Models with Jam Protection Function on Driver Door Window Only:

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSTALLATION


Hide 84870A 38.INSTALL OUTER MIRROR SWITCH ASSEMBLY (for Driver Side, w/ Power Window)

Hide 39.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side, w/ Power Window)

a.

Connect each connector.


b.
B412119C01
0.031,0.094 0.281,0.313 0.25,0.219 10 true *A 0.042,2.458 0.292,2.677 0.25,0.219 10 true *B
*A for Single Cab, Smart Cab
*B for Double Cab
V113147

Install in this Direction


Attach the claw and clip to install the power window regulator master switch assembly with front door armrest base panel as shown in the illustration.


Hide 84810 40.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side, w/ Power Window)

Hide 41.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side, w/ Power Window)

a.

Connect the connector.


b.
B412120C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and clip to install the power window regulator switch assembly with front door armrest base panel as shown in the illustration.


Hide 69260 42.INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

a.
B412121C01
0.698,1.854 0.938,1.854 0.938,1.854 0.938,1.26 false 3.146,0.719 3.385,0.917 0.24,0.198 10 false *a 2.708,0.396 3.021,0.594 0.313,0.198 10 false *b 0.5,1.75 0.813,1.948 0.313,0.198 10 false *1
*1 Plate
*a Front
*b 30°


With the door window fully closed, install the plate and front door window regulator handle with the snap ring as shown in the illustration.


Hide 74220 43.INSTALL FRONT ARMREST ASSEMBLY LH

a.
B412122C01
0,0 0,0 false
V113147

Install in this Direction


for Single Cab, Smart Cab:

Attach the claw and clip to install the front armrest assembly LH.


b.
B412123C01
0,0 0,0 false
V113147

Install in this Direction


for Double Cab:

Attach the claw and clip to install the front armrest assembly LH.


Hide 67492A 44.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.

Attach the guide and clip to install the front door lower frame bracket garnish LH.

B404233C03
0.083,0.083 0.396,0.281 0.313,0.198 10 true *A 3.677,0.063 3.99,0.26 0.313,0.198 10 true *B
*A w/ Front No. 2 Speaker *B w/o Front No. 2 Speaker



Hide 45.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 46.CHECK SRS WARNING LIGHT (w/ Curtain Shield Airbag)