Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT AIRBAG SENSOR › 2015.06–2016.03
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0189250 FRONT AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89174A 1.INSTALL FRONT AIRBAG SENSOR LH

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·
B392779

If this procedure is performed without disconnecting the negative (-) terminal of the battery, the airbag may deploy even if an impact is applied only to the front airbag sensor LH. Therefore, make sure that the negative (-) terminal of the battery is disconnected before performing this procedure.




c.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

B340848C02
4.583,0.594 4.896,0.75 0.313,0.156 10 *a 4.677,1.875 4.99,2.031 0.313,0.156 10 *b 1.385,0.615 1.698,0.771 0.313,0.156 10 *a 1.448,1.865 1.76,2.021 0.313,0.156 10 *b
*a Incorrect *b Correct



ii.

While holding the CPA be sure to engage the connectors until they are locked and check that the CPA is in its original position (when locking, make sure that a click sound can be heard).

NOTICE:

Do not push down the upper part of the CPA shown in the illustration when connecting the airbag connector.


B399097C02
2.396,1.031 2.813,0.615 true 2.479,1.802 2.479,1.385 true 2.26,0.813 2.677,0.396 true 2.708,0.281 3.021,0.438 0.313,0.156 10 false *c 5.917,2.208 6.229,2.365 0.313,0.156 10 false *d 2.875,0.51 3.188,0.667 0.313,0.156 10 false *a 2.417,1.844 2.729,2 0.313,0.156 10 false *b
*a Housing Lock *b CPA
*c CPA Upper Part *d Connection is Completed
V113147

Connect in this Direction - -




d.

Attach the guide and hold the front airbag sensor LH in place.


e.

Install the nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the front airbag sensor LH has been dropped, replace it with a new one.

·

When installing the front airbag sensor LH, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Tighten the nut while holding the front airbag sensor LH because the front airbag sensor LH guide is easily damaged.




f.

Check that there is no looseness in the installation parts of the front airbag sensor LH.


Hide 52119A 2.INSTALL FRONT BUMPER COVER (for Steel Type Bumper)

Hide 53117C 3.INSTALL NO. 1 RADIATOR GRILLE RETAINER (for Steel Type Bumper)

Hide 4.INSTALL FRONT BUMPER COVER (for Resin Type Bumper)

Hide 5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION