Home › Engine / Hybrid System › 2TR-FE COOLING › RADIATOR › 2015.06–2016.01
RM3250E _51 Engine / Hybrid System _038026 2TR-FE COOLING _0191184 RADIATOR A

2TR-FE COOLING  RADIATOR  INSTALLATION  


PROCEDURE

Hide 16407A 1.INSTALL RADIATOR DRAIN COCK PLUG

a.

Install a new O-ring to the radiator drain cock plug.


b.

Install the radiator drain cock plug to the radiator assembly.


Hide 16400 2.INSTALL RADIATOR ASSEMBLY

a.

Set the radiator assembly to the vehicle.


b.

Attach the 2 guides and 2 claws to connect the cooler condenser assembly to the radiator assembly.

NOTICE:
·

Do not apply any excessive force to the cooler condenser assembly and cooler pipe.

·

Do not allow the radiator assembly to interfere with other parts.




c.
A341296C03
2.667,1.833 2.833,1.833 2.833,1.833 2.958,1.552 true 2.833,0.25 2.667,0.25 2.667,0.25 2.75,0.5 true 2.5,1.75 2.729,1.948 0.229,0.198 10 true *a 2.875,0.156 3.104,0.354 0.229,0.198 10 true *a
*a Claw


Hook the claw of the radiator assembly as shown in the illustration.


d.
A344518N01
2.76,0.76 2.865,0.958 0.104,0.198 10 true 1 0.573,0.75 0.729,0.948 0.156,0.198 10 false 2 2.792,1.229 2.896,1.417 0.104,0.188 10 true 3 0.583,1.292 0.74,1.49 0.156,0.198 10 false 4

Install the radiator assembly with the 4 bolts in the order shown in the illustration.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 16711 3.INSTALL FAN SHROUD

a.

Install a new clamp to the fan shroud.


b.

Install the fan pulley to the engine water pump assembly.


c.

Place the fan shroud together with the fluid coupling fan between the radiator assembly and engine.

NOTICE:

Be careful not to damage the radiator core.



d.

Install the coupling fan to the engine water pump assembly with the 4 nuts. Tighten the nuts as much as possible by hand.


e.
A340084

Attach the 2 guides and 2 claws of the fan shroud to the radiator as shown in the illustration.


f.

Install the fan and generator V belt.

Click hereEngine / Hybrid System>2TR-FE ENGINE MECHANICAL>DRIVE BELT>INSTALLATION


g.

Tighten the 4 nuts of the fluid coupling fan.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


h.
A349953

Attach the 6 clamps to the radiator assembly and fan shroud to connect the wire harness.


Hide 16470 4.INSTALL RADIATOR RESERVOIR

a.

Install the radiator reservoir and grommet with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the reservoir hose to the radiator assembly.


Hide 32941 5.CONNECT NO. 1 OIL COOLER INLET HOSE (for Automatic Transmission)

a.

Connect the No. 1 oil cooler inlet hose to the radiator assembly, and slide the hose clamp to secure the hose.

NOTICE:

Connect the No. 1 oil cooler inlet hose to the radiator assembly so that the paint mark on the No. 1 oil cooler inlet hose is facing upwards.



Hide 32942 6.CONNECT NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transmission)

a.

Connect the No. 1 oil cooler outlet hose to the radiator assembly, and slide the hose clamp to secure the hose.

NOTICE:

Connect the No. 1 oil cooler outlet hose to the radiator assembly so that the paint mark on the No. 1 oil cooler outlet hose is facing upwards.



Hide 17621A 7.CONNECT AIR PUMP INLET (w/ Secondary Air Injection System)

Hide 16572 8.INSTALL RADIATOR HOSE OUTLET

a.
A355188C01
1.01,2.646 1.438,2.646 1.438,2.646 1.625,2.844 true 1.927,2.813 2.25,2.625 2.25,2.625 2.375,2.625 true 0.823,2.552 1.01,2.74 0.188,0.188 10 false *a 2.406,2.552 2.625,2.75 0.219,0.198 10 false *b
*a Paint Mark
*b Protrusion


Connect the radiator hose outlet to the radiator assembly and water inlet, and slide the 2 hose clamps to secure the hose.

NOTICE:

Connect the radiator hose outlet so that the paint mark on the radiator hose outlet is aligned with the protrusions of the radiator assembly and water inlet as shown in the illustration.



b.

Attach the clamp to the radiator hose outlet.


Hide 16571 9.INSTALL RADIATOR HOSE INLET

a.
A355187C02
2.573,2.49 2.833,2.583 2.833,2.583 2.958,2.583 true 0.344,2.49 0.677,2.49 0.677,2.49 0.865,2.667 true 2.031,2.771 2.115,2.771 2.115,2.771 2.49,2.531 true 1.073,2.615 1.229,2.26 1.229,2.26 1.333,2.26 true 2.531,2.25 2.615,2.177 2.615,2.177 2.76,2.177 false 0.167,2.396 0.333,2.594 0.167,0.198 10 false *a 1.365,2.177 1.542,2.365 0.177,0.188 10 false *b 2.979,2.49 3.156,2.677 0.177,0.188 10 true *c 1.885,2.677 2.042,2.854 0.156,0.177 10 true *a 2.802,2.104 3.198,2.302 0.396,0.198 10 false 26.6°
*a Paint Mark
*b Protrusion
*c Machined Edge


Connect the radiator hose inlet to the radiator assembly and cylinder head, and slide the 2 hose clamps to secure the hose.

NOTICE:

Connect the radiator hose inlet so that the paint mark on the radiator hose inlet is aligned with the protrusion of the radiator assembly and the machined edge of the engine as shown in the illustration.



b.

w/ Secondary Air Injection System:

Connect the hose clamp to the radiator hose inlet.


Hide 16593 12.INSTALL NO. 1 RADIATOR AIR GUIDE

a.

Install the No. 1 radiator air guide with 4 new clips.


Hide 51410 13.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY