Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › CAMSHAFT
RM3250E _51 Engine / Hybrid System _038014 2KD-FTV ENGINE MECHANICAL _0193255 CAMSHAFT A

2KD-FTV ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the camshaft sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of injector assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting (Click here)
Replacement of timing belt Mode reset operation
·

Does not illuminate when replacement is necessary

·

Illuminates when replacement is not necessary


(Click here)

CAUTION:
A343691

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (for 4WD and Pre-Runner)

Hide 16571C 4.REMOVE NO. 1 RADIATOR HOSE

Hide 16711 5.REMOVE FAN SHROUD

Hide 15301 8.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 23701 9.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

Hide 23704 10.REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

Hide 23770 11.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 11201 12.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23670 13.REMOVE INJECTOR ASSEMBLY

Hide 11322A 14.REMOVE NO. 1 TIMING BELT COVER

Hide 13505 16.REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

Hide 13523P 17.REMOVE CAMSHAFT TIMING PULLEY

Hide 11322B 18.REMOVE NO. 2 TIMING BELT COVER

Hide 19.REMOVE CAMSHAFT SUB-ASSEMBLY

a.
A352032C01
0.479,0.635 1.375,0.26 1.375,0.26 1.563,0.26 true 1.594,0.146 1.844,0.313 0.25,0.167 10 false *a 0.438,0.042 0.75,0.24 0.313,0.198 10 false *b
*a Key Groove
*b Upward


Turn the intake camshaft sub-assembly with a wrench so that the key groove of the intake camshaft sub-assembly faces upward.


b.
A352033N01
1.198,1.979 1.333,2.146 0.135,0.167 10 true 1 0.052,0.896 0.188,1.063 0.135,0.167 10 true 2 0.625,1.865 0.76,2.031 0.135,0.167 10 true 3 3.156,0.688 3.292,0.854 0.135,0.167 10 true 4 1.854,0.021 1.99,0.188 0.135,0.167 10 true 5 2.927,0.063 3.063,0.229 0.135,0.167 10 true 6 1.958,1.594 2.094,1.76 0.135,0.167 10 true 7 1.521,0.083 1.729,0.25 0.208,0.167 10 true 11 0.75,0.552 0.885,0.719 0.135,0.167 10 true 8 1.271,1.438 1.406,1.604 0.135,0.167 10 true 9 2.75,0.979 2.958,1.146 0.208,0.167 10 true 10 1.958,0.896 2.167,1.063 0.208,0.167 10 true 12 2.417,1.24 2.625,1.406 0.208,0.167 10 true 13 1.146,0.281 1.354,0.448 0.208,0.167 10 true 14 1.521,1.104 1.729,1.271 0.208,0.167 10 true 15

Uniformly loosen the 15 camshaft bearing cap bolts in several passes in the sequence shown in the illustration.


c.

Remove the 15 camshaft bearing cap bolts, No. 1 camshaft bearing cap, 3 No. 2 camshaft bearing caps, No. 3 camshaft bearing cap, camshaft oil seal and intake camshaft sub-assembly and exhaust camshaft sub-assembly from the cylinder head sub-assembly.