Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › CYLINDER HEAD GASKET
RM3250E _51 Engine / Hybrid System _038014 2KD-FTV ENGINE MECHANICAL _0193256 CYLINDER HEAD GASKET A

2KD-FTV ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of injector assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting (Click here)
for 2KD-FTV:

Replacement of diesel throttle body assembly


Perform initialization - (Click here)
Replacement of timing belt Mode reset operation
·

Does not illuminate when replacement is necessary

·

Illuminates when replacement is not necessary


(Click here)

CAUTION:
A343691

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 19850 5.REMOVE GLOW PLUG ASSEMBLY

Hide 23670 6.REMOVE INJECTOR ASSEMBLY

Hide 23810A 7.REMOVE COMMON RAIL ASSEMBLY

Hide 16711 9.REMOVE FAN SHROUD

Hide 88320 10.DISCONNECT COOLER COMPRESSOR ASSEMBLY

Hide 88431 11.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 11322A 12.REMOVE NO. 1 TIMING BELT COVER

Hide 13505 14.REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

Hide 13523P 15.REMOVE CAMSHAFT TIMING PULLEY

a.
A352040

Remove the bolt of the camshaft timing pulley while holding the intake camshaft sub-assembly with a wrench.

NOTICE:

Make sure to remove the bolt of the camshaft timing pulley with the timing belt not installed.



b.

Remove the camshaft timing pulley from the intake camshaft sub-assembly.


Hide 11322B 16.REMOVE NO. 2 TIMING BELT COVER

a.

Remove the 4 bolts, nut and No. 2 timing belt cover from the cylinder head sub-assembly and timing gear cover.


Hide 17.REMOVE CAMSHAFT SUB-ASSEMBLY

Hide 11101 19.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A352041N01
2.708,1.438 2.844,1.604 0.135,0.167 10 true 1 0.844,0.229 0.979,0.396 0.135,0.167 10 true 2 2.729,0.229 2.865,0.396 0.135,0.167 10 true 3 0.854,1.417 0.99,1.583 0.135,0.167 10 true 4 2.5,0.125 2.635,0.292 0.135,0.167 10 true 5 1.073,1.563 1.208,1.729 0.135,0.167 10 true 6 1.083,0.115 1.219,0.281 0.135,0.167 10 true 8 2.25,1.448 2.385,1.615 0.135,0.167 10 true 9 2.479,1.563 2.615,1.729 0.135,0.167 10 true 7 1.271,0.229 1.458,0.396 0.188,0.167 10 true 10 2.208,0.229 2.396,0.396 0.188,0.167 10 true 11 1.271,1.438 1.458,1.604 0.188,0.167 10 true 12 1.979,0.115 2.167,0.281 0.188,0.167 10 true 13 1.5,1.563 1.688,1.729 0.188,0.167 10 true 14 1.958,1.563 2.146,1.729 0.188,0.167 10 true 15 1.531,0.115 1.719,0.281 0.188,0.167 10 true 16 1.729,1.438 1.917,1.604 0.188,0.167 10 true 17 1.729,0.229 1.917,0.396 0.188,0.167 10 true 18

Uniformly loosen the 18 cylinder head set bolts in several passes in the sequence shown in the illustration. Then remove the 18 cylinder head set bolts and 18 washers.

NOTICE:

Cylinder head warpage or cracking could result from removing bolts in the incorrect order.



b.

Lift the cylinder head sub-assembly from the dowels on the cylinder block sub-assembly, and place the cylinder head sub-assembly on wooden blocks on a bench.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and cylinder block sub-assembly.


HINT:

If the cylinder head sub-assembly is difficult to lift, use a screwdriver to pry between the cylinder head sub-assembly and cylinder block sub-assembly.



Hide 11115 20.REMOVE CYLINDER HEAD GASKET