Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY › 2015.06–2016.01
RM3250E _52 Drivetrain _038029 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0193347 AUTOMATIC TRANSMISSION ASSEMBLY A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the automatic transmission assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Automatic transmission assembly Reset memory
·

Large shift shock

·

Engine overruns


(Click here)

CAUTION:
·
C313282C04
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


The automatic transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.

·
A356209

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·

Wear protective gloves when removing the exhaust pipe assembly.

·

The exhaust pipe assembly is extremely hot immediately after the engine has stopped.

·

Confirm that the exhaust pipe assembly has cooled down before removing it.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 41110F 3.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY

Hide 37100 6.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 17410 8.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 33820B 9.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

C111231

a.

Remove the nut and clip and disconnect the transmission control cable assembly.


Hide 10.DISCONNECT OIL COOLER TUBE

C324044

a.

Using a union nut wrench, disconnect the outlet oil cooler tube and inlet oil cooler tube.

HINT:

Use a container to catch any ATF which flows out of the 2 oil cooler tubes and automatic transmission assembly.



b.
C324045

Remove the 3 bolts and 3 oil cooler tube clamps.


c.

Remove the 4 bolts and 3 oil cooler tube clamps from the automatic transmission assembly and engine assembly.

HINT:

It is not necessary to remove the oil cooler clamp they are being replaced.



Hide 33823 11.REMOVE TRANSMISSION CONTROL CABLE BRACKET

C111232

a.

Remove the 2 bolts and transmission control cable bracket from the automatic transmission assembly.


Hide 82284 12.DISCONNECT GROUND WIRE

a.
C324360

Remove the bolt and disconnect ground wire from the transfer assembly.


Hide 13.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

a.
C111233

Support the automatic transmission assembly with a transmission jack.

NOTICE:
·

In order to protect the automatic transmission oil pan sub-assembly, place attachments on the transmission jack.

·

Make sure that the attachments and the automatic transmission oil pan sub-assembly are centered on the transmission jack.

·

To prevent the automatic transmission oil pan sub-assembly from deforming, do not place any attachments under the automatic transmission oil pan sub-assembly of the automatic transmission assembly.

·

Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.




Hide 33118B 14.REMOVE STIFFENER PLATE

C187502C04
0.135,0.135 0.396,0.354 0.26,0.219 10 true *a 0.135,2.438 0.427,2.688 0.292,0.25 10 true *b
*a LH Side
*b RH Side


a.

Remove the 4 bolts and stiffener plate RH (with oil cooler tube clamp).


b.

Remove the 4 bolts and stiffener plate LH.


c.

Remove the No. 4 cylinder block insulator.


d.

Remove the No. 2 end plate.


Hide 15.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C324050

Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each bolt while holding the crankshaft pulley set bolt with a wrench.


Hide 51204 16.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

C324241

a.

Remove the 4 bolts and disconnect the No. 3 frame crossmember sub-assembly from the rear engine mounting insulator.


b.

Remove the 4 nuts, 4 bolts and No. 3 frame crossmember sub-assembly.


Hide 12371A 17.REMOVE REAR ENGINE MOUNTING INSULATOR

a.
C324234

Remove the 4 bolts and rear engine mounting insulator from the automatic transmission assembly.


Hide 82121 18.DISCONNECT ENGINE WIRE

a.
C112845

Tilt the automatic transmission assembly downward.

NOTICE:

Make sure that the cooling fan and fan shroud do not contact the engine when tilting the automatic transmission assembly.



b.
C324362

Detach the 5 clamps and disconnect the transfer breather hose sub-assembly from the automatic transmission assembly.


c.
C324363C01
1.469,1.813 1.302,1.813 1.302,1.813 1.302,1.229 true 1.531,1.729 1.708,1.938 0.177,0.208 10 false *a
*a Transmission Wire Connector


Disconnect the 5 connectors.

HINT:

Detach the claw and press down the lever to disconnect engine wire from the transmission wire connector.



d.

Remove the bolt, detach the 7 wire harness clamps and disconnect the engine wire from the automatic transmission assembly and transfer assembly.


Hide 19.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

CAUTION:

The automatic transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.


a.
C324051

Remove the 5 bolts.


b.

Remove the automatic transmission assembly.

NOTICE:
·

Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.

·

Do not use excess force to pry on the automatic transmission assembly.




Hide 36100 20.REMOVE TRANSFER ASSEMBLY

Hide 21.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C324364

Remove the 3 bolts and 3 wire harness clamp brackets.


Hide 36478A 22.REMOVE TRANSMISSION BREATHER BRACKET

a.
C324400

Detach the clamp to disconnect the automatic transmission breather hose from the transfer breather bracket.


b.

Remove the bolt and transmission breather bracket.


Hide 32000 23.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C324401C01
1.302,0.333 0.75,0.333 true 1.521,0.563 0.75,0.333 true 0.583,0.25 0.896,0.448 0.313,0.198 10 false *a
*a Matchmark


Put matchmarks on the automatic transmission assembly and the torque converter assembly.


b.

Remove the torque converter assembly from the automatic transmission assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.