Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT
RM3250E _52 Drivetrain _038029 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0193348 AUTOMATIC TRANSMISSION UNIT A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 35573 1.REMOVE TRANSMISSION CONTROL SHAFT LEVER LH

C324244

a.

Remove the nut, spring washer and transmission control shaft lever LH.


Hide 84540 2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C324215

Using a screwdriver, bend the tabs of the lock washer.


b.
C324245

Remove the nut, lock washer and bolt.


c.

Remove the park/neutral position switch assembly.

HINT:

Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.



Hide 3.REMOVE OIL COOLER TUBE UNION

C324246

a.

Remove the 2 oil cooler tube unions.


b.

Remove the 2 O-rings from the 2 oil cooler tube unions.


Hide 89413N 4.REMOVE TRANSMISSION REVOLUTION SENSOR (NT)

Hide 89413R 5.REMOVE TRANSMISSION REVOLUTION SENSOR (SP2)

Hide 35122 6.REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE

a.
C324247

Remove the 2 bolts and remove the automatic transmission breather tube.


b.
C324366C01
0.115,0.427 0.115,0.177 0.115,0.177 0.281,0.177 false 0.906,1.073 0.906,0.823 0.906,0.823 1.073,0.823 false 2.406,1.427 2.406,1.76 2.406,1.76 2.24,1.76 false 3.26,1.594 3.26,1.844 3.26,1.844 3.094,1.844 false 0.333,0.083 0.646,0.281 0.313,0.198 10 false *1 1.115,0.729 1.427,0.927 0.313,0.198 10 false *2 2.052,1.667 2.365,1.865 0.313,0.198 10 false *3 2.927,1.75 3.24,1.948 0.313,0.198 10 false *4
*1 No. 1 Breather Plug
*2 Automatic Transmission Breather Hose
*3 Automatic Transmission Breather Tube
*4 O-ring


Remove the O-ring from the automatic transmission breather tube.


c.

Remove the No. 1 breather plug and automatic transmission breather hose from the automatic transmission breather tube.


Hide 35111 7.REMOVE AUTOMATIC TRANSMISSION HOUSING

C268494

a.

Remove the 10 bolts.


b.

Remove the automatic transmission housing.


Hide 36107A 8.REMOVE TRANSFER ADAPTER SUB-ASSEMBLY

C283889

a.

Remove the 8 bolts.


b.

Remove the rear transfer adapter sub-assembly.

HINT:

Use a brass bar and a hammer to remove the rear transfer adapter sub-assembly.



c.

Remove the 2 transfer case ring pins from the rear transfer adapter sub-assembly.


Hide 36117A 9.REMOVE TRANSFER ADAPTER OIL SEAL

C111209C04
2.042,1.031 2.083,1.083 2.083,1.083 2.073,1.115 false 1.906,1.021 1.938,1.094 1.938,1.094 1.938,1.146 false 1.802,1.01 1.813,1.063 1.813,1.063 1.792,1.115 false 1.667,1.01 1.656,1.083 false 1.583,0.99 1.573,1.073 false 1.708,1.031 0.927,0.313 0.927,0.313 0.74,0.313 true 0.563,0.219 0.875,0.375 0.313,0.156 10 false *a
*a Protective Tape


a.

Using a screwdriver, pry out the transfer case adapter rear oil seal.

NOTICE:

Be careful not to damage the rear transfer adapter sub-assembly.


HINT:

Tape the screwdriver with tip before use.



Hide 35157B 10.REMOVE REAR TRANSFER CASE ADAPTER OIL RECEIVER

C190069

a.

Using snap ring pliers, remove the snap ring and rear transfer case adapter oil receiver.


Hide 35104 11.FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

C324061

a.

Install the automatic transmission case sub-assembly to an overhaul attachment.


Hide 35106 12.REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

NOTICE:

Do not turn the transmission over as this will contaminate the valve body with foreign matter on the bottom of the automatic transmission oil pan sub-assembly.


a.

Remove the overflow plug and gasket.


b.

Remove the drain plug and gasket.


c.
C324038

Remove the 20 bolts, automatic transmission oil pan sub-assembly and gasket.


d.

Examine particles in the pan.

i.

Remove the 4 magnets from the automatic transmission oil pan sub-assembly. Use the removed magnets to collect any steel chips. Look carefully for the chips and particles in the automatic transmission oil pan sub-assembly and on the magnets to anticipate the type of wear which might be found in the transmission.

Result:

Steel (magnetic):

Bearing, gear and plate wear


Brass (non-magnetic):

Bushing wear




Hide 35330 13.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

a.

Turn over the automatic transmission case sub-assembly.


b.

Remove the valve body oil strainer assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TRANSMISSION WIRE>REMOVAL


Hide 35410 15.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

Hide 35145C 16.REMOVE TRANSMISSION CASE GASKET

C324065

a.

Remove the 3 transmission case gaskets.


Hide 35159 17.REMOVE BRAKE DRUM GASKET

C324066

a.

Remove the 3 brake drum gaskets.


Hide 35251 18.REMOVE CHECK BALL BODY

C324067C01
0.99,1.042 1.49,1.042 true 1.021,0.563 1.271,0.563 false 0.833,0.479 1.146,0.677 0.313,0.198 10 false *1 0.813,0.958 1.125,1.156 0.313,0.198 10 false *2
*1 Check Ball Body
*2 Spring


a.

Remove the check ball body and spring.


Hide 35425A 19.REMOVE C-2 ACCUMULATOR PISTON

C324068

a.

Apply compressed air to the oil hole to remove the C-2 accumulator piston and spring.


b.

Remove the 2 O-rings from the C-2 accumulator piston.

NOTICE:

Be careful as the C-3 and B-3 accumulator pistons may jump out.



Hide 35427K 20.REMOVE B-3 ACCUMULATOR PISTON

C324068

a.

Apply compressed air to the oil hole to remove the B-3 accumulator piston and spring.


b.

Remove the 2 O-rings from the B-3 accumulator piston.

NOTICE:

Be careful as the C-3 accumulator piston may jump out.



Hide 35426D 21.REMOVE C-3 ACCUMULATOR PISTON

C324069

a.

Apply compressed air to the oil hole to remove the C-3 accumulator piston and 2 springs.


b.

Remove the 2 O-rings from the C-3 accumulator piston.


Hide 35424F 22.REMOVE C-1 ACCUMULATOR VALVE

C324070

a.

Remove the C-1 accumulator valve and 2 springs.


Hide 35595 23.REMOVE PARKING LOCK PAWL BRACKET

C324071

a.

Remove the 3 bolts and parking lock pawl bracket.


Hide 35501 24.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

C324072

a.

Disconnect the parking lock rod sub-assembly from the manual valve lever sub-assembly.


Hide 35556 25.REMOVE PARKING LOCK PAWL SHAFT

C324073C01
0.667,0.667 0.833,0.667 0.833,0.667 1,0.333 true 2.375,0.76 2.667,0.333 2.667,0.333 2.833,0.333 true 2.385,0.938 2.635,0.938 2.635,0.938 2.802,0.938 true 2.417,1.583 2.667,1.583 2.667,1.583 2.917,1.583 true 0.5,0.583 0.729,0.771 0.229,0.188 10 true *1 2.875,0.25 3.104,0.438 0.229,0.188 10 true *2 2.844,0.844 3.073,1.031 0.229,0.188 10 true *3 2.958,1.5 3.188,1.688 0.229,0.188 10 true *4
*1 Parking Lock Pawl
*2 E-ring
*3 Parking Lock Pawl Shaft
*4 Spring


a.

Pull out the parking lock pawl shaft from the front side, and then remove the parking lock pawl and spring.


b.

Remove the E-ring from the parking lock pawl shaft.


Hide 35505 26.REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

C324074C01
1.958,0.219 2.177,0.219 2.177,0.219 2.708,0.458 true 1.792,0.146 2.104,0.344 0.313,0.198 10 false *a
*a Protective Tape


a.

Using a hammer and a screwdriver, cut off the spacer and remove it from the manual valve lever shaft.

NOTICE:

Be careful not to damage the manual valve lever shaft.


HINT:

Tape the screwdriver tip before use



b.
C324075

Using a pin punch and a hammer, drive out the spring pin.

HINT:

Slowly drive out the spring pin so that it does not fall into the transmission case sub-assembly.



c.

Pull the manual valve lever shaft out through the automatic transmission case sub-assembly and remove the manual valve lever sub-assembly.


Hide 35506F 27.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

C324076C01
1.708,0.698 2.198,0.698 true 2.25,0.625 2.5,0.823 0.25,0.198 10 true *a
*a Protective Tape


a.

Using a screwdriver, pry out the 2 manual valve lever shaft oil seals.

NOTICE:

Be careful not to damage the automatic transmission case sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 28.REMOVE OIL PUMP ASSEMBLY

C324077

a.

Remove the 10 bolts.


b.
C161630E01
2.68,0.691 2.999,0.879 0.319,0.189 10 SST 2.645,0.827 2.182,0.949 false

Using SST, remove the oil pump assembly.

SST
09950-40011  (09951-04010, 09953-04020, 09952-04010, 09954-04010, 09955-04031, 09958-04011)


c.
C122832C02
2.083,0.167 2.271,0.167 2.271,0.167 2.417,0.302 false 1.813,1.719 1.906,1.813 1.906,1.813 2.156,1.813 false 0.75,1.354 0.75,0.708 0.75,0.708 0.635,0.708 false 1.896,0.063 2.135,0.25 0.24,0.188 10 false *3 0.448,0.604 0.688,0.792 0.24,0.188 10 false *1 2.198,1.708 2.438,1.896 0.24,0.188 10 false *2
*1 No. 1 Thrust Bearing Race
*2 O-ring
*3 Oil Pump Assembly


Remove the No. 1 thrust bearing race from the oil pump assembly.


d.

Remove the O-ring from the oil pump assembly.


Hide 29.REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

C324079

a.

Remove the clutch drum and input shaft assembly from the automatic transmission case sub-assembly.


b.
C324080C01
0.333,1.198 0.667,0.75 0.667,0.75 0.833,0.75 false 0.667,0.75 0.917,1.167 false 0.719,1.552 0.719,1.802 0.719,1.802 0.885,1.802 false 3.042,0.5 3.042,0.25 3.042,0.25 2.875,0.25 false 0.875,0.677 1.188,0.875 0.313,0.198 10 false *1 0.938,1.719 1.25,1.917 0.313,0.198 10 false *2 2.698,0.167 3.01,0.365 0.313,0.198 10 false *3
*1 Thrust Needle Roller Bearing
*2 No. 2 Thrust Bearing Race
*3 Clutch Drum Thrust Washer


Remove the clutch drum thrust washer, 2 thrust needle roller bearings and No. 2 thrust bearing race.


Hide 35780B 30.INSPECT NO. 2 ONE-WAY CLUTCH ASSEMBLY

Hide 35780B 31.REMOVE NO. 2 ONE-WAY CLUTCH ASSEMBLY

C324081C01
2.698,0.135 2.865,0.135 2.865,0.135 2.865,0.385 false 2.375,1.271 2.375,1.521 2.375,1.521 2.542,1.521 false 1.229,0.365 1.396,0.365 1.396,0.365 1.396,0.615 false 2.542,0.052 2.854,0.25 0.313,0.198 10 false *1 2.604,1.448 2.917,1.646 0.313,0.198 10 false *2 1.073,0.313 1.385,0.51 0.313,0.198 10 false *3
*1 No. 2 One-way Clutch Assembly
*2 No. 2 Clutch Drum Thrust Washer
*3 Clutch Drum and Input Shaft Assembly


a.

Remove the No. 2 one-way clutch assembly and No. 2 clutch drum thrust washer from the clutch drum and input shaft assembly.


Hide 35601 32.FIX CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

a.
C324082C01
2.406,1.688 2.573,1.354 2.573,1.354 2.74,1.354 false 1.083,1.333 0.833,0.917 0.833,0.917 0.667,0.917 false 2.219,0.75 2.385,0.417 2.385,0.417 2.552,0.417 false 2.792,1.271 3.104,1.469 0.313,0.198 10 false *1 0.5,0.833 0.813,1.031 0.313,0.198 10 false *2 2.594,0.333 2.906,0.531 0.313,0.198 10 false *3
*1 Torque Converter Assembly
*2 Oil Pump Assembly
*3 Clutch Drum and Input shaft assembly


Place the oil pump assembly onto the torque converter assembly, and then place the clutch drum and input shaft assembly onto the oil pump assembly.


Hide 35049 33.REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY

a.
C324083C01
2.573,0.938 2.896,0.938 false 2.927,0.844 3.24,1.042 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, remove the snap ring from the clutch drum and input shaft assembly.

NOTICE:

Be careful not to damage the reverse clutch piston sub-assembly, clutch drum and input shaft assembly.


HINT:

Tape the screwdriver tip before use.



b.
C324084

Remove the reverse clutch hub sub-assembly with the reverse clutch reaction sleeve, clutch cushion plate, reverse clutch flange, 5 reverse clutch discs and 4 reverse clutch plates from the reverse clutch hub sub-assembly.


Hide 35659 34.REMOVE REVERSE CLUTCH REACTION SLEEVE

a.
C324085

Remove the reverse clutch reaction sleeve from the reverse clutch hub sub-assembly.


Hide 35677C 35.REMOVE REVERSE CLUTCH DISC

a.

Remove the clutch cushion plate, reverse clutch flange, 5 reverse clutch discs and 4 clutch plates from the reverse clutch hub sub-assembly.


Hide 35049 37.INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY

Hide 35061 38.REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

a.
C324086

Remove the forward clutch hub sub-assembly from the clutch drum.


b.
C324087

Remove the 2 thrust needle roller bearings from the forward clutch hub sub-assembly.


Hide 35061 39.INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY

Hide 35631 40.REMOVE MULTIPLE DISC CLUTCH HUB

a.
C324088

Remove the multiple disc clutch hub from the clutch drum.


b.
C324089C01
2.917,1.5 2.917,1.167 false 0.5,1.031 0.5,0.781 0.5,0.781 0.667,0.781 false 2.844,1.521 3.156,1.719 0.313,0.198 10 false *1 0.708,0.698 1.021,0.896 0.313,0.198 10 false *2
*1 No. 3 Thrust Bearing Race
*2 No. 4 Thrust Bearing Race


Remove the No. 3 thrust bearing race and No. 4 thrust bearing race from the multiple disc clutch hub.


Hide 35701 41.REMOVE INPUT SHAFT ASSEMBLY

a.
C324090

Remove the thrust needle roller bearing from the clutch drum.


b.
C324091

Remove the input shaft assembly from the clutch drum.


Hide 35712A 42.REMOVE INPUT SHAFT OIL SEAL RING

C284160

a.

Remove the 3 input shaft oil seal rings from the input shaft assembly.


Hide 35633B 43.REMOVE FORWARD MULTIPLE DISC CLUTCH DISC

a.
C324092C01
0.917,0.573 1.292,0.573 false 0.74,0.479 1.052,0.677 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, remove the snap ring.

NOTICE:

Be careful not to damage the input shaft assembly.


HINT:

Tape the screwdriver tip before use.



b.

Remove the 2 forward clutch flanges, 7 forward multiple disc clutch discs and 6 clutch plates from the input shaft assembly.


Hide 35633B 44.INSPECT FORWARD MULTIPLE DISC CLUTCH DISC

Hide 35668 45.REMOVE NO. 1 CLUTCH BALANCER

C324093N01
1.583,0.333 2.333,0.333 true 1.969,0.667 2.167,0.333 true 2.396,0.26 2.854,0.458 0.458,0.198 10 false SST

a.

Place SST on the No. 1 clutch balancer, and compress the forward clutch return spring sub-assembly with a press.

SST
09350-30020  (09350-07040)


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.
C324094C01
0.333,0.458 0.5,0.458 false 0.448,1.167 0.615,1.167 false 0.167,0.385 0.479,0.583 0.313,0.198 10 false *1 0.271,1.094 0.583,1.292 0.313,0.198 10 false *2
*1 No. 1 Clutch Balancer
*2 Forward Clutch Return Spring Sub-assembly


Remove the No. 1 clutch balancer and forward clutch return spring sub-assembly from the input shaft assembly.


d.
C324095

Remove the O-ring from the No. 1 clutch balancer.


Hide 35603A 46.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35612B 47.REMOVE FORWARD CLUTCH PISTON

a.
C324096

Hold the input shaft assembly by hand and apply compressed air to the input shaft assembly to remove the forward clutch piston.


b.
C324097

Remove the 2 O-rings from the forward clutch piston.


Hide 35649 48.REMOVE REVERSE CLUTCH FLANGE

C324098

a.

Remove the reverse clutch flange from the clutch drum.


Hide 35667A 49.REMOVE DIRECT CLUTCH DISC

a.
C324099C01
2.094,0.688 2.323,0.396 2.323,0.396 2.531,0.396 false 2.583,0.302 2.896,0.5 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, remove the 2 snap rings from the clutch drum.

NOTICE:

Be careful not to damage the reverse clutch drum.


HINT:

Tape the screwdriver tip before use.



b.

Remove the direct clutch flange, 6 direct clutch discs and 6 clutch plates from the clutch drum.


Hide 35688 51.REMOVE NO. 3 CLUTCH BALANCER

a.
C324100N01
1.667,0.917 2.5,0.333 2.5,0.333 2.75,0.333 true 2.083,0.917 2.5,0.333 true 2.792,0.271 3.25,0.469 0.458,0.198 10 false SST

Place SST on the No. 3 clutch balancer, and compress the reverse clutch return spring sub-assembly with a press.

SST
09387-00070  


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.

Remove the No. 3 clutch balancer.


Hide 35047 52.REMOVE REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C324101C01
0.646,0.865 0.646,0.615 0.646,0.615 0.479,0.615 false 1.448,0.667 1.448,0.417 1.448,0.417 1.281,0.417 false 2.385,1.573 2.385,1.823 2.385,1.823 2.219,1.823 false 0.323,0.552 0.635,0.75 0.313,0.198 10 false *1 1.104,0.344 1.417,0.542 0.313,0.198 10 false *2 2.042,1.75 2.354,1.948 0.313,0.198 10 false *3
*1 Reverse Clutch Return Spring Sub-assembly
*2 O-ring
*3 Reverse Clutch Piston Sub-assembly


Remove the reverse clutch return spring sub-assembly and O-ring from the reverse clutch piston sub-assembly.


Hide 35047 53.INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35048 54.REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY

a.
C324102C01
0.635,0.771 0.635,0.271 0.635,0.271 0.802,0.271 false 2.573,1.417 2.573,1.75 2.573,1.75 2.406,1.75 false 0.854,0.188 1.167,0.385 0.313,0.198 10 false *1 2.229,1.667 2.542,1.865 0.313,0.198 10 false *2
*1 Reverse Clutch Piston Sub-assembly
*2 Clutch Drum


Remove the reverse clutch piston sub-assembly from the reverse clutch drum.


b.
C324103

Remove the O-ring from the reverse clutch piston sub-assembly.


c.
C324104

Remove the O-ring from the clutch drum.


Hide 35606A 55.REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

C285716N01
1.75,1.271 2.542,1.958 2.542,1.958 2.375,1.344 true 2.49,1.99 2.833,2.177 0.344,0.188 10 false SST

a.

Place SST on the No. 2 clutch balancer, and compress the direct clutch return spring sub-assembly with a press.

SST
09320-89010  


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.
C324105C01
2.542,0.948 2.792,0.948 false 0.625,0.917 0.875,0.917 false 2.854,0.854 3.167,1.052 0.313,0.198 10 false *a 0.448,0.813 0.76,1.01 0.313,0.198 10 false *a
*a Protective Tape


Using 2 screwdrivers, remove the direct clutch piston sub-assembly from the clutch drum.

NOTICE:

Be careful not to damage the direct clutch piston sub-assembly.


HINT:

Tape the screwdriver tip before use.



d.
D028516

Remove the O-ring from the clutch drum.


e.
C324107C01
2.615,1.75 2.781,1.75 2.781,1.75 2.781,1.417 false 1.344,0.365 1.51,0.365 1.51,0.365 1.51,0.615 false 0.417,0.594 0.583,0.594 0.583,0.594 0.583,0.844 false 2.448,1.677 2.76,1.875 0.313,0.198 10 false *1 1.177,0.292 1.49,0.49 0.313,0.198 10 false *2 0.26,0.521 0.573,0.719 0.313,0.198 10 false *3
*1 Direct Clutch Piston Sub-assembly
*2 Direct Clutch Return Spring Sub-assembly
*3 No. 2 Clutch Balancer


Remove the No. 2 clutch balancer and direct clutch return spring sub-assembly from the direct clutch piston sub-assembly.


f.
C324108

Remove the 2 O-rings from the direct clutch piston sub-assembly.


Hide 35604 56.INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 57.REMOVE NO. 3 BRAKE DISC

a.
C324109C01
1.917,0.865 2.177,0.865 false 2.229,0.781 2.542,0.979 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.

NOTICE:

Be careful not to damage the automatic transmission case sub-assembly.


HINT:

Tape the screwdriver tip before use.



b.

Remove the No. 3 brake flange, brake cushion plate, 4 No. 3 brake discs and 4 No. 3 brake plates from the automatic transmission case sub-assembly.


Hide 35790 59.REMOVE ONE-WAY CLUTCH ASSEMBLY

C324110

a.

Remove the one-way clutch assembly and No. 1 planetary carrier thrust washer from the automatic transmission case sub-assembly.


Hide 35664 60.REMOVE 2ND BRAKE CYLINDER

C324111N01
2.99,1.406 2.99,1.198 2.99,1.198 2.125,0.531 true 2.844,1.438 3.302,1.635 0.458,0.198 10 true SST

a.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07060)


b.
C324112

Remove the 2nd brake cylinder from the automatic transmission case sub-assembly.


Hide 35624 61.REMOVE 2ND BRAKE PISTON

a.
C324113C01
2.5,0.5 2.667,0.167 2.667,0.167 2.833,0.167 true 1.552,1.354 1.885,0.688 1.885,0.688 2.052,0.688 true 2.875,0.083 3.333,0.281 0.458,0.198 10 false SST 2.115,0.615 2.573,0.813 0.458,0.198 10 false *a
*a Protective Tape


Using SST, a screwdriver and a press, compress the 2nd brake piston return spring sub-assembly and remove the snap ring.

SST
09351-40010  (09351-04060, 09351-04070)

NOTICE:

Be careful not to damage the 2nd brake cylinder.


HINT:

Tape the screwdriver tip before use.



b.

Remove the 2nd brake piston return spring sub-assembly.


c.
C324114

Hold the 2nd brake cylinder and apply compressed air to the 2nd brake cylinder to remove the 2nd brake piston.


d.
C324115C01
1.75,0.625 1.75,0.292 1.75,0.292 1.917,0.292 true 1.302,1.333 1.302,1 1.302,1 1.469,1 true 1.948,0.219 2.26,0.417 0.313,0.198 10 false *1 1.531,0.927 1.844,1.125 0.313,0.198 10 false *1
*1 O-ring


Remove the 2 O-rings from the 2nd brake piston.


Hide 35046 62.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35720 63.REMOVE FRONT PLANETARY GEAR ASSEMBLY

C324116C01
2.344,0.469 2.927,0.469 true 2.302,1.021 2.885,1.021 true 2.958,0.375 3.271,0.573 0.313,0.198 10 false *1 2.938,0.938 3.25,1.135 0.313,0.198 10 false *2
*1 One-way Clutch Inner Race
*2 Front Planetary Gear Assembly


a.

Remove the front planetary gear assembly and one-way clutch inner race from the automatic transmission case sub-assembly.


b.
C324117C01
1.146,0.292 0.979,0.292 false 0.438,0.958 0.271,0.958 false 0.521,1.458 0.438,1.292 0.438,1.292 0.271,1.292 false 1.188,0.219 1.417,0.417 0.229,0.198 10 true *3 0.094,0.875 0.323,1.073 0.229,0.198 10 false *2 0.104,1.208 0.333,1.406 0.229,0.198 10 false *1
*1 No. 2 Planetary Carrier Thrust Washer
*2 Thrust Needle Roller Bearing
*3 No. 3 Thrust Bearing Race


Remove the thrust needle roller bearing, No. 3 thrust bearing race and No. 2 planetary carrier thrust washer from the automatic transmission case sub-assembly.


Hide 66.REMOVE FRONT PLANETARY RING GEAR

C324118

a.

Remove the front planetary ring gear and thrust needle roller bearing from the automatic transmission case sub-assembly.


Hide 35763 67.REMOVE CENTER PLANETARY RING GEAR

C324119C01
2.76,1.313 2.583,1.313 2.583,1.313 2.438,1.031 false 2.813,1.229 3.125,1.427 0.313,0.198 10 false *a
*a Protective Tape


a.

Using a screwdriver, remove the snap ring.

NOTICE:

Be careful not to damage the front planetary ring gear and center planetary ring gear.


HINT:

Tape the screwdriver tip before use.



b.
C324120C01
0.771,0.625 0.771,0.375 0.771,0.375 0.938,0.375 false 2.677,0.333 2.833,0.167 2.833,0.167 3,0.167 false 2.823,1.094 2.979,0.927 2.979,0.927 3.146,0.927 false 1,0.302 1.313,0.5 0.313,0.198 10 false *1 3.042,0.104 3.354,0.302 0.313,0.198 10 false *2 3.198,0.865 3.406,1.021 0.208,0.156 10 false *3
*1 Center Planetary Ring Gear
*2 Front Planetary Ring Gear Flange
*3 Front Planetary Ring Gear


Remove the center planetary ring gear and front planetary ring gear flange from the front planetary ring gear.


Hide 35681A 68.REMOVE NO. 1 BRAKE DISC

a.

Remove the No. 1 brake flange, 3 No. 1 brake discs and 3 No. 1 brake plates from the automatic transmission case sub-assembly.


Hide 35698 70.REMOVE NO. 1 BRAKE CYLINDER

C324121C01
1.021,0.583 1.188,0.583 1.188,0.583 1.604,0.833 true 0.833,0.51 1.146,0.708 0.313,0.198 10 false *a
*a Protective Tape


a.

Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.

NOTICE:

Be careful not to damage the automatic transmission case sub-assembly.


HINT:

Tape the screwdriver tip before use.



b.
C324122C01
1.083,0.167 1.25,0.167 1.25,0.167 1.458,0.365 false 2.24,1.167 2.917,1.167 true 0.927,0.094 1.24,0.292 0.313,0.198 10 false *1 2.969,1.094 3.281,1.292 0.313,0.198 10 false *2
*1 Brake Piston Return Spring Sub-assembly
*2 No. 1 Brake Cylinder


Remove the brake piston return spring sub-assembly, No. 1 brake piston and No. 1 brake cylinder from the automatic transmission case sub-assembly.


Hide 35608J 71.INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35621V 72.REMOVE NO. 1 BRAKE PISTON

C324123

a.

Hold the No. 1 brake cylinder and apply compressed air to the No. 1 brake cylinder to remove the No. 1 brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.

Remove the 2 O-rings from the No. 1 brake piston.


Hide 35682A 73.REMOVE NO. 2 BRAKE DISC

C324124C01
1.885,0.854 2.26,0.573 2.26,0.573 2.438,0.573 true 2.5,0.5 2.729,0.698 0.229,0.198 10 true *a
*a Protective Tape


a.

Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.

NOTICE:

Be careful not to damage the automatic transmission case sub-assembly.


HINT:

Tape the screwdriver tip before use.



b.

Remove the No. 2 brake flange, 3 No. 2 brake discs, 3 No. 2 brake plates and No. 2 brake piston return spring from the automatic transmission case sub-assembly.


Hide 35045 75.INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35622G 76.REMOVE NO. 2 BRAKE PISTON

C324125

a.

Apply compressed air to the transmission case to remove the No. 2 brake piston.

HINT:

If the No. 2 brake piston does not pop out with compressed air, lift the No. 2 brake piston out with needle-nose pliers.



b.

Remove the 2 O-rings from the No. 2 brake piston.


c.

Remove the No. 2 brake cylinder from the automatic transmission case sub-assembly.


Hide 35750 77.REMOVE CENTER PLANETARY GEAR ASSEMBLY

C324250C01
0.531,0.333 0.698,0.333 0.698,0.333 0.698,0.583 false 0.271,0.854 0.438,0.854 0.438,0.854 0.521,1.021 false 0.406,1.771 0.573,1.771 false 0.354,0.25 0.667,0.448 0.313,0.198 10 false *1 0.104,0.771 0.417,0.969 0.313,0.198 10 false *2 0.229,1.688 0.542,1.885 0.313,0.198 10 false *3
*1 No. 4 Thrust Bearing Race
*2 Center Planetary Gear Assembly
*3 Planetary Sun Gear


a.

Remove the No. 4 thrust bearing race, center planetary gear and planetary sun gear from the automatic transmission case sub-assembly.


Hide 35750 78.INSPECT CENTER PLANETARY GEAR ASSEMBLY

Hide 35713 79.REMOVE INTERMEDIATE SHAFT

C324126C01
2.135,1.115 2.781,0.896 2.781,0.896 2.979,0.896 true 3.042,0.802 3.354,1 0.313,0.198 10 false *a
*a Protective Tape


a.

Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.

NOTICE:

Be careful not to damage the automatic transmission case sub-assembly.


HINT:

Tape the screwdriver tip before use.



b.
C324127

Remove the intermediate shaft with the No. 3 one-way clutch assembly from the automatic transmission case sub-assembly.


Hide 35770C 80.INSPECT NO. 3 ONE-WAY CLUTCH ASSEMBLY

Hide 35770C 81.REMOVE NO. 3 ONE-WAY CLUTCH ASSEMBLY

C324128C01
1.104,0.74 1.104,0.406 1.104,0.406 1.271,0.406 false 0.354,1.198 0.354,0.865 0.354,0.865 0.521,0.865 false 1.313,0.313 1.625,0.51 0.313,0.198 10 false *1 0.563,0.792 0.875,0.99 0.313,0.198 10 false *2
*1 No. 3 One-way Clutch Assembly
*2 One-way Clutch Inner Race


a.

Remove the No. 3 one-way clutch assembly and one-way clutch inner race from the intermediate shaft.


Hide 35077D 82.REMOVE REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY WITH REAR PLANETARY RING GEAR

C324129C01
1.573,0.917 1.573,0.667 1.573,0.667 1.74,0.667 false 1.396,1.229 1.396,1.479 1.396,1.479 1.563,1.479 false 1.146,1.021 1.146,0.76 1.146,0.76 0.979,0.76 false 0.646,1.688 0.813,1.938 0.813,1.938 0.979,1.938 false 1.594,1.406 1.906,1.604 0.313,0.198 10 false *2 1.031,1.854 1.344,2.052 0.313,0.198 10 false *4 0.813,0.677 1.125,0.875 0.313,0.198 10 false *1 1.792,0.594 2.104,0.792 0.313,0.198 10 false *3
*1 No. 7 Thrust Bearing Race
*2 Thrust Needle Roller Bearing
*3 No. 8 Thrust Bearing Race
*4 Rear Planetary Ring Gear Flange Sub-assembly


a.

Remove the rear planetary ring gear flange sub-assembly with rear planetary ring gear, No. 7 thrust bearing race, thrust needle roller bearing and No. 8 thrust bearing race from the intermediate shaft.


Hide 35077D 83.INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

Hide 35761 84.REMOVE REAR PLANETARY RING GEAR

a.
C321210C01
2.396,0.563 2.708,0.563 false 2.771,0.479 3.083,0.677 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, remove the snap ring from the rear planetary ring gear flange sub-assembly with rear planetary ring gear.

NOTICE:

Be careful not to damage the rear planetary ring gear flange sub-assembly with rear planetary ring gear.


HINT:

Tape the screwdriver tip before use.



b.
C321211C01
2.125,0.594 2.615,0.594 false 2.167,1.677 2.656,1.677 false 2.688,0.51 3,0.708 0.313,0.198 10 false *1 2.719,1.594 3.031,1.792 0.313,0.198 10 false *2
*1 Rear Planetary Ring Gear Flange Sub-assembly
*2 Rear Planetary Ring Gear


Remove the rear planetary ring gear from the rear planetary ring gear flange sub-assembly.


Hide 35639B 86.REMOVE BRAKE PLATE STOPPER SPRING

C324130

a.

Remove the brake plate stopper spring from the automatic transmission case sub-assembly.


Hide 87.REMOVE NO. 4 BRAKE DISC

a.

Remove the 7 No. 4 brake plates, 8 No. 4 brake discs and 2 No. 4 brake flanges from the automatic transmission case sub-assembly.


Hide 35719B 89.REMOVE REAR PLANETARY GEAR ASSEMBLY

C190075

a.

Remove the rear planetary gear assembly from the automatic transmission case sub-assembly.


b.
C190076

Remove the 2 thrust needle roller bearings from the rear planetary gear assembly.


c.
C324258

Remove the No. 9 thrust bearing race from the automatic transmission case sub-assembly.


Hide 35068 91.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C324134C01
1,0.5 1.167,0.5 1.167,0.5 1.333,0.833 false 2.781,0.5 2.615,0.5 2.615,0.5 2.448,1.083 true 0.729,0.438 1.188,0.635 0.458,0.198 10 false SST 2.833,0.438 3.104,0.646 0.271,0.208 10 false *1
*1 Snap Ring


a.

Place SST on the 1st and reverse brake return spring sub-assembly and compress the 1st and reverse brake return spring sub-assembly.

SST
09350-30020  (09350-07050)


b.

Using SST, remove the snap ring and 1st and reverse brake return spring sub-assembly.

SST
09350-30020  (09350-07070)


Hide 35068 92.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

Hide 35623H 93.REMOVE 1ST AND REVERSE BRAKE PISTON

C324135

a.

Apply compressed air to the automatic transmission case sub-assembly to remove the 1st and reverse brake piston.

HINT:

If the 1st and reverse brake piston does not pop out with compressed air, lift the 1st and reverse brake piston out with needle-nose pliers.



b.

Remove the O-ring from the 1st and reverse brake piston.


Hide 35626 94.REMOVE BRAKE REACTION SLEEVE

C324136N01
1.229,0.417 1.479,0.417 false 0.938,0.344 1.396,0.542 0.458,0.198 10 false SST

a.

Using SST, remove the brake reaction sleeve.

SST
09350-30020  (09350-07080)


b.

Remove the 2 O-rings from the brake reaction sleeve.


Hide 35629A 95.REMOVE NO. 4 BRAKE PISTON

C324137N01
1.313,0.5 1.563,0.5 false 1.042,0.417 1.5,0.615 0.458,0.198 10 false SST

a.

Using SST, remove the No. 4 brake piston.

SST
09350-30020  (09350-07090)


b.

Remove the 2 O-rings from the No. 4 brake piston.