Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT
RM3250E _52 Drivetrain _038029 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0193348 AUTOMATIC TRANSMISSION UNIT A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

C324257N01
1.604,0.792 1.76,0.99 0.156,0.198 10 false A 2.854,2.031 3.01,2.229 0.156,0.198 10 false B 4.833,1.406 4.99,1.604 0.156,0.198 10 false E 3.51,3.292 3.667,3.49 0.156,0.198 10 false C 4.719,3.063 4.875,3.26 0.156,0.198 10 false D 4.646,4.469 4.802,4.667 0.156,0.198 10 false G 5.833,4.25 5.99,4.448 0.156,0.198 10 false F 4.198,6.104 4.354,6.302 0.156,0.198 10 false J 1.885,6.708 2.042,6.906 0.156,0.198 10 false H 4.438,7.531 4.594,7.729 0.156,0.198 10 false I

Bearing and Race Diameter:
Mark Front Race Diameter Inside/Outside Thrust Bearing Diameter Inside/Outside Rear Race Diameter Inside/Outside
A 74.2 mm (2.92 in.) / 87.74 mm (3.45 in.) 71.9 mm (2.83 in.) / 85.6 mm (3.37 in.) -
B 37.0 mm (1.46 in.) / 52.3 mm (2.06 in.) 34.6 mm (1.36 in.) / 52.0 mm (2.05 in.) -
C - 21.3 mm (0.839 in.) / 41.1 mm (1.62 in.) 22.6 mm (0.890 in.) / 45.0 mm (1.77 in.)
D 38.4 mm (1.51 in.) / 56.5 mm (2.22 in.) 33.3 mm (1.31 in.) / 51.5 mm (2.03 in.) -
E - 42.5 mm (1.67 in.) / 61.2 mm (2.41 in.) -
F 38.0 mm (1.50 in.) / 57.0 mm (2.24 in.) 43.4 mm (1.71 in.) / 58.3 mm (2.30 in.) -
G - 55.7 mm (2.19 in.) / 76.4 mm (3.01 in.) 53.7 mm (2.11 in.) / 74.0 mm (2.91 in.)
H 33.4 mm (1.31 in.) / 49.0 mm (1.93 in.) 32.1 mm (1.26 in.) / 49.35 mm (1.94 in.) 32.1 mm (1.26 in.) / 49.0 mm (1.93 in.)
I - 21.5 mm (0.846 in.) / 40.8 mm (1.61 in.) -
J - 43.55 mm (1.71 in.) / 61.0 mm (2.40 in.) 47.1 mm (1.85 in.) / 67.1 mm (2.64 in.)


Hide 35629A 2.ASSEMBLE NO. 4 BRAKE PISTON AND BRAKE REACTION SLEEVE

C324185C01
1.583,1.333 2,1.917 true 1.521,0.313 1.688,0.313 1.688,0.313 1.854,0.479 false 2.25,1 2.667,0.167 2.667,0.167 2.833,0.167 true 2.583,0.5 2.667,0.167 true 0.479,1.333 0.729,1.333 false 1,1.333 2,1.917 2,1.917 2.167,1.917 true 2.885,0.083 3.198,0.281 0.313,0.198 10 false *1 2.219,1.833 2.531,2.031 0.313,0.198 10 false *1 1.344,0.229 1.656,0.427 0.313,0.198 10 false *3 0.323,1.25 0.635,1.448 0.313,0.198 10 false *2
*1 O-ring
*2 Brake Reaction Sleeve
*3 No. 4 Brake Piston


a.

Coat 2 new O-rings with ATF, and install them to the brake reaction sleeve.


b.

Coat 2 new O-rings with ATF, and install them to the No. 4 brake piston.


c.

Install the No. 4 brake piston to the brake reaction sleeve.

NOTICE:

Be careful not to damage the O-rings.



Hide 35626 3.INSTALL NO. 4 BRAKE PISTON WITH BRAKE REACTION SLEEVE

C324186C01
1.146,1.219 1.146,0.802 1.146,0.802 1.313,0.802 false 2.5,1.5 2.5,0.75 2.5,0.75 2.667,0.75 false 1.354,0.74 1.667,0.938 0.313,0.198 10 false *1 2.708,0.677 3.021,0.875 0.313,0.198 10 false *2
*1 Brake Reaction Sleeve
*2 No. 4 Brake Piston


a.

Install the No. 4 brake piston with brake reaction sleeve to the automatic transmission case sub-assembly.

NOTICE:

Be careful not to damage the O-ring.



Hide 35623H 4.INSTALL 1ST AND REVERSE BRAKE PISTON

a.

Coat a new O-ring with ATF.


b.
C324187C01
1.104,1.104 1.323,0.688 1.323,0.688 1.521,0.688 false 1.583,0.604 1.896,0.802 0.313,0.198 10 false *1
*1 1st and Reverse Brake Piston


Install the O-ring to the 1st and reverse brake piston.


c.

With the spring seat of the 1st and reverse brake piston facing upwards (front side), place the 1st and reverse brake piston in the automatic transmission case sub-assembly.

NOTICE:

Be careful not to damage the O-ring.



Hide 35068 5.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C324188

Place the 1st and reverse brake return spring sub-assembly onto the 1st and reverse brake piston.


b.
C324134C01
1,0.5 1.167,0.5 1.167,0.5 1.333,0.833 false 2.781,0.5 2.615,0.5 2.615,0.5 2.448,1.083 true 0.729,0.438 1.188,0.635 0.458,0.198 10 false SST 2.833,0.438 3.104,0.646 0.271,0.208 10 false *1
*1 Snap Ring


Place SST on the 1st and reverse brake return spring sub-assembly, and compress the 1st and reverse brake return spring sub-assembly.

SST
09350-30020  (09350-07050)


c.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)


Hide 35719B 6.INSTALL REAR PLANETARY GEAR ASSEMBLY

a.

Install the No. 9 thrust bearing race.

Thrust Bearing Race Diameter:
Item Inside Outside
No. 9 Thrust Bearing Race
(Rear race J)
47.1 mm (1.85 in.) 67.1 mm (2.64 in.)



b.
C190076C03
0.552,1.26 0.698,0.385 0.698,0.385 0.854,0.385 false 2.844,0.969 2.729,1.688 2.729,1.688 2.552,1.688 false 0.917,0.292 1.146,0.51 0.229,0.219 10 false *1 2.365,1.594 2.573,1.802 0.208,0.208 10 false *2
*1 Thrust Needle Roller Bearing
(Thrust Bearing I)
*2 Thrust Needle Roller Bearing
(Thrust Bearing J)


Coat the 2 thrust needle roller bearings with ATF, and install them to the rear planetary gear assembly.

Thrust Needle Roller Bearing Diameter:
Item Inside Outside
Thrust needle roller bearing
(Thrust bearing J)
43.55 mm (1.71 in.) 61.0 mm (2.40 in.)
Thrust needle roller bearing
(Thrust bearing I)
21.5 mm (0.846 in.) 40.8 mm (1.61 in.)



c.

Install the rear planetary gear assembly.


Hide 7.INSPECT PACK CLEARANCE OF 1ST AND REVERSE BRAKE

Hide 35684 8.INSTALL NO. 4 BRAKE DISC

a.
C324259C01
0.219,0.771 0.448,0.771 false 0.24,0.99 0.469,0.99 false 0.219,1.188 0.448,1.188 false 0.24,1.406 0.469,1.406 false 0.208,1.604 0.438,1.604 false 0.24,1.813 0.469,1.813 false 0.208,2.021 0.438,2.021 false 0.25,2.25 0.479,2.25 false 0.208,2.438 0.438,2.438 false 0.24,2.656 0.469,2.656 false 0.208,2.854 0.438,2.854 false 0.25,3.063 0.479,3.063 false 0.219,3.271 0.448,3.271 false 0.25,3.49 0.479,3.49 false 0.219,3.688 0.448,3.688 false 0.25,3.917 0.479,3.917 false 0.219,4.146 0.448,4.146 false 0.052,0.698 0.26,0.865 0.208,0.167 10 false *1 0.083,0.906 0.292,1.073 0.208,0.167 10 false *2 0.063,1.115 0.271,1.281 0.208,0.167 10 false *3 0.073,1.323 0.281,1.49 0.208,0.167 10 false *2 0.042,1.531 0.25,1.698 0.208,0.167 10 false *3 0.083,1.74 0.292,1.906 0.208,0.167 10 false *2 0.042,1.938 0.25,2.104 0.208,0.167 10 false *3 0.083,2.167 0.292,2.333 0.208,0.167 10 false *2 0.052,2.365 0.26,2.531 0.208,0.167 10 false *3 0.094,2.573 0.302,2.74 0.208,0.167 10 false *2 0.052,2.771 0.26,2.938 0.208,0.167 10 false *3 0.083,2.979 0.292,3.146 0.208,0.167 10 false *2 0.063,3.198 0.271,3.365 0.208,0.167 10 false *3 0.083,3.417 0.292,3.583 0.208,0.167 10 false *2 0.042,3.604 0.25,3.771 0.208,0.167 10 false *3 0.083,3.833 0.292,4 0.208,0.167 10 false *2 0.052,4.063 0.26,4.229 0.208,0.167 10 false *1
*1 No. 4 Brake Flange
*2 No. 4 Brake Disc
*3 No. 4 Brake Plate


Install the 2 flanges, 8 discs and 7 plates.

NOTICE:
·

Make sure that the No. 4 brake discs, No. 4 brake plates and No. 4 brake flanges are installed in the correct order.

·

Install the thicker No. 4 brake flange first, and then install the thinner one.




Hide 35639B 9.INSTALL BRAKE PLATE STOPPER SPRING

a.
C324130

Install the brake plate stopper spring.


Hide 35761 10.INSTALL REAR PLANETARY RING GEAR

a.
C321211C01
2.125,0.594 2.615,0.594 false 2.167,1.677 2.656,1.677 false 2.688,0.51 3,0.708 0.313,0.198 10 false *1 2.719,1.594 3.031,1.792 0.313,0.198 10 false *2
*1 Rear Planetary Ring Gear Flange Sub-assembly
*2 Rear Planetary Ring Gear


Install the rear planetary ring gear to the rear planetary ring gear flange sub-assembly.


b.
C321210C01
2.396,0.563 2.708,0.563 false 2.771,0.479 3.083,0.677 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, install the snap ring to the rear planetary ring gear flange sub-assembly with rear planetary ring gear.

NOTICE:

Be careful not to damage the rear planetary ring gear flange sub-assembly with rear planetary ring gear.


HINT:

Tape the screwdriver tip before use.



Hide 35077D 11.INSTALL REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY WITH REAR PLANETARY RING GEAR

a.
C324129C01
1.573,0.917 1.573,0.667 1.573,0.667 1.74,0.667 false 1.396,1.229 1.396,1.479 1.396,1.479 1.563,1.479 false 1.146,1.021 1.146,0.76 1.146,0.76 0.979,0.76 false 0.646,1.688 0.813,1.938 0.813,1.938 0.979,1.938 false 1.594,1.406 1.906,1.604 0.313,0.198 10 false *2 1.031,1.854 1.344,2.052 0.313,0.198 10 false *4 0.813,0.677 1.125,0.875 0.313,0.198 10 false *1 1.792,0.594 2.104,0.792 0.313,0.198 10 false *3
*1 No. 7 Thrust Bearing Race
(Front Race H)
*2 Thrust Needle Roller Bearing
(Thrust Bearing H)
*3 No. 8 Thrust Bearing Race
(Rear Race H)
*4 Rear Planetary Ring Gear Flange Sub-assembly


Install the No. 8 thrust bearing race, thrust needle roller bearing, No. 7 thrust bearing race and rear planetary ring gear flange sub-assembly with the rear planetary ring gear to the intermediate shaft.

Thrust Needle Roller Bearing and Race Diameter:
Item Inside Outside
No. 7 thrust bearing race
(Front Race H)
33.4 mm (1.31 in.) 49.0 mm (1.93 in.)
Thrust needle roller bearing
(Thrust bearing H)
32.1 mm (1.26 in.) 49.35 mm (1.94 in.)
No. 8 thrust bearing race
(Rear race H)
32.1 mm (1.26 in.) 49.0 mm (1.93 in.)



Hide 35770C 12.INSTALL NO. 3 ONE-WAY CLUTCH ASSEMBLY

C324128C01
1.104,0.74 1.104,0.406 1.104,0.406 1.271,0.406 false 0.354,1.198 0.354,0.865 0.354,0.865 0.521,0.865 false 1.313,0.313 1.625,0.51 0.313,0.198 10 false *1 0.563,0.792 0.875,0.99 0.313,0.198 10 false *2
*1 No. 3 One-way Clutch Assembly
*2 One-way Clutch Inner Race


a.

Install the No. 3 one-way clutch assembly and one-way clutch inner race to the intermediate shaft.


Hide 35713 13.INSTALL INTERMEDIATE SHAFT

a.

Install the intermediate shaft with the No. 3 one-way clutch assembly to the automatic transmission case sub-assembly.


b.
C324261N01
1.198,0.344 1.5,0.344 true 0.896,0.25 1.24,0.49 0.344,0.24 10 true SST

Using SST, install the snap ring.

SST
09350-30020  (09350-07060)


Hide 35750 14.INSTALL CENTER PLANETARY GEAR ASSEMBLY

C324250C01
0.531,0.333 0.698,0.333 0.698,0.333 0.698,0.583 false 0.271,0.854 0.438,0.854 0.438,0.854 0.521,1.021 false 0.406,1.771 0.573,1.771 false 0.354,0.25 0.667,0.448 0.313,0.198 10 false *1 0.104,0.771 0.417,0.969 0.313,0.198 10 false *2 0.229,1.688 0.542,1.885 0.313,0.198 10 false *3
*1 No. 4 Thrust Bearing Race
(Rear Race G)
*2 Center Planetary Gear Assembly
*3 Planetary Sun Gear


a.

Install the planetary sun gear and center planetary gear to the case.


b.

Coat the No. 4 thrust bearing race with ATF, and install it onto the center planetary gear assembly.

Thrust Bearing Race Diameter:
Item Inside Outside
No. 4 thrust bearing race
(Rear race G)
53.7 mm (2.11 in.) 74.0 mm (2.91 in.)



Hide 35622G 15.INSTALL NO. 2 BRAKE PISTON

a.
C324189C01
0.656,1.208 1,0.333 1,0.333 1.25,0.333 true 1.135,0.667 1,0.333 true 1.302,0.26 1.615,0.458 0.313,0.198 10 false *1
*1 O-ring


Coat 2 new O-rings with ATF, and install them to the No. 2 brake piston.


b.

Press the No. 2 brake piston into the No. 2 brake cylinder.

NOTICE:

Be careful not to damage the O-rings.



c.

Install the No. 2 brake piston to the automatic transmission case sub-assembly.

HINT:

Install the No. 2 brake cylinder so that the projection protrudes from the upside of the automatic transmission case sub-assembly.



d.
C324190

Check that the oil pressure apply hole of the No. 2 brake cylinder aligns with the oil pressure apply hole of the automatic transmission case sub-assembly.


Hide 35682A 16.INSTALL NO. 2 BRAKE DISC

C324191C01
0.188,0.354 0.354,0.354 false 0.219,0.583 0.385,0.583 false 0.219,0.76 0.385,0.76 false 0.208,1 0.375,1 false 0.219,1.167 0.385,1.167 false 0.219,1.406 0.385,1.406 false 0.229,1.563 0.396,1.563 false 0.26,1.813 0.427,1.813 false 0.031,0.271 0.344,0.469 0.313,0.198 10 false *3 0.063,0.5 0.375,0.698 0.313,0.198 10 false *2 0.063,0.677 0.375,0.875 0.313,0.198 10 false *1 0.052,0.906 0.365,1.104 0.313,0.198 10 false *2 0.063,1.083 0.375,1.281 0.313,0.198 10 false *1 0.063,1.313 0.375,1.51 0.313,0.198 10 false *2 0.052,1.479 0.365,1.677 0.313,0.198 10 false *1 0.094,1.719 0.406,1.917 0.313,0.198 10 false *4
*1 No. 2 Brake Plate
*2 No. 2 Brake Disc
*3 No. 2 Brake Flange
*4 No. 2 Brake Piston Return Spring Sub-assembly


a.

Install the No. 2 brake flange, 3 No. 2 brake plates, 3 No. 2 brake discs and No. 2 brake piston return spring sub-assembly.

NOTICE:
·

Make sure that the No. 2 brake piston return spring sub-assembly, No. 2 brake discs, No. 2 brake plates and No. 2 brake flanges are installed in the correct order.

·

Install the thicker No. 2 brake piston return spring sub-assembly, and then install the thinner one.




b.
C324192C01
2.083,1.5 2.5,1.75 2.5,1.75 2.667,1.75 false 1.75,1.167 2.5,1.75 true 1.917,0.5 2.5,1.75 true 0.406,1.396 1.323,1.396 true 2.719,1.656 3.031,1.854 0.313,0.198 10 false SST 0.229,1.302 0.542,1.5 0.313,0.198 10 false *a
*a Protective Tape


Using SST and a screwdriver, compress the No. 2 brake piston return spring sub-assembly and install the snap ring to the automatic transmission case sub-assembly.

SST
09351-40010  (09351-04010, 09351-04020, 09351-04040, 09351-04050)

NOTICE:

Be careful not to damage the automatic transmission case sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35621V 17.INSTALL NO. 1 BRAKE PISTON

C324193C01
1.281,0.563 1.25,0.167 true 1.021,0.917 1.25,0.167 1.25,0.167 1,0.167 true 0.823,0.094 1.135,0.292 0.313,0.198 10 false *1
*1 O-ring


a.

Coat 2 new O-rings with ATF, and install them to the No. 1 brake piston.


b.

Press the No. 1 brake piston into the No. 1 brake cylinder.

NOTICE:

Be careful not to damage the 2 O-rings.



Hide 35608J 18.INSTALL BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C324194C01
1,0.365 1.417,0.365 false 2.219,1.188 2.969,1.188 true 0.833,0.292 1.146,0.49 0.313,0.198 10 false *1 3.021,1.115 3.333,1.313 0.313,0.198 10 false *2
*1 Brake Piston Return Spring Sub-assembly
*2 No. 1 Brake Cylinder


a.

Install the brake piston return spring sub-assembly and the No. 1 brake piston with the No. 1 brake cylinder to the automatic transmission case sub-assembly.


b.
C324195

Check that the oil pressure apply hole of the No. 1 brake cylinder aligns with the oil pressure apply hole of the automatic transmission case sub-assembly.


c.
C324196C01
2.167,1.635 2.583,1.75 2.583,1.75 2.75,1.75 true 2.583,1.75 1.75,1.417 true 2.583,1.75 2,1 true 0.458,1.427 1.375,1.427 true 2.802,1.667 3.26,1.865 0.458,0.198 10 false SST 0.281,1.333 0.74,1.531 0.458,0.198 10 false *a
*a Protective Tape


Using SST and a screwdriver, compress the brake piston return spring sub-assembly and install the snap ring to the automatic transmission case sub-assembly.

SST
09351-40010  (09351-04010, 09351-04030, 09351-04040, 09351-04050)

NOTICE:

Be careful not to damage the automatic transmission case sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35763 19.INSTALL CENTER PLANETARY RING GEAR

a.
C324120C01
0.771,0.625 0.771,0.375 0.771,0.375 0.938,0.375 false 2.677,0.333 2.833,0.167 2.833,0.167 3,0.167 false 2.823,1.094 2.979,0.927 2.979,0.927 3.146,0.927 false 1,0.302 1.313,0.5 0.313,0.198 10 false *1 3.042,0.104 3.354,0.302 0.313,0.198 10 false *2 3.198,0.865 3.406,1.021 0.208,0.156 10 false *3
*1 Center Planetary Ring Gear
*2 Front Planetary Ring Gear Flange
*3 Front Planetary Ring Gear


Install the center planetary ring gear and front planetary ring gear flange on the front planetary ring gear.


b.
C324119C01
2.76,1.313 2.583,1.313 2.583,1.313 2.438,1.031 false 2.813,1.229 3.125,1.427 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, install the snap ring.

NOTICE:
·

Install the snap ring to the ring gear so that the both ends of the snap ring come to the center of a protrusion on the ring gear.

·

Be careful not to damage the front planetary ring gear.



HINT:

Tape the screwdriver tip before use.



Hide 35743 20.INSTALL FRONT PLANETARY RING GEAR

a.

Coat the thrust needle roller bearing with ATF, and install it to the front planetary ring gear flange.

Thrust Bearing Race Diameter:
Item Inside Outside
Thrust needle roller bearing
(Thrust bearing G)
55.7 mm (2.19 in.) 76.4 mm (3.01 in.)



b.
C324118

Install the front planetary ring gear to the automatic transmission case sub-assembly.


c.
C324117C01
1.146,0.292 0.979,0.292 false 0.438,0.958 0.271,0.958 false 0.521,1.458 0.438,1.292 0.438,1.292 0.271,1.292 false 1.188,0.219 1.417,0.417 0.229,0.198 10 true *3 0.094,0.875 0.323,1.073 0.229,0.198 10 false *2 0.104,1.208 0.333,1.406 0.229,0.198 10 false *1
*1 No. 2 Planetary Carrier Thrust Washer
*2 Thrust Needle Roller Bearing
(Thrust Bearing F)
*3 No. 3 Thrust Bearing Race
(Front Race F)


Coat the No. 2 planetary carrier thrust washer and thrust needle roller bearing, and install them.


d.

Coat the No. 3 thrust bearing race with ATF, and install it onto the front planetary ring gear.

Thrust Needle Roller Bearing and Race Diameter:
Item Inside Outside
Thrust needle roller bearing
(Thrust bearing F)
43.4 mm (1.71 in.) 58.3 mm (2.30 in.)
No. 3 thrust bearing race
(Front race F)
38.0 mm (1.50 in.) 57.0 mm (2.24 in.)



Hide 35720 21.INSTALL FRONT PLANETARY GEAR ASSEMBLY

a.
C324116C01
2.344,0.469 2.927,0.469 true 2.302,1.021 2.885,1.021 true 2.958,0.375 3.271,0.573 0.313,0.198 10 false *1 2.938,0.938 3.25,1.135 0.313,0.198 10 false *2
*1 One-way Clutch Inner Race
*2 Front Planetary Gear Assembly


Install the front planetary gear assembly and one-way clutch inner race to the automatic transmission case sub-assembly.


Hide 22.INSPECT PACK CLEARANCE OF NO. 1 BRAKE PISTON

Hide 35681A 23.INSTALL NO. 1 BRAKE DISC

C324197C01
0.167,0.469 0.365,0.469 false 0.167,0.708 0.365,0.708 false 0.167,0.865 0.365,0.865 false 0.167,1.083 0.365,1.083 false 0.167,1.25 0.365,1.25 false 0.156,1.438 0.354,1.438 false 0.177,1.625 0.344,1.625 false 0.021,0.385 0.333,0.583 0.313,0.198 10 false *3 0.01,0.625 0.323,0.823 0.313,0.198 10 false *2 0.021,0.802 0.333,1 0.313,0.198 10 false *1 0.021,1 0.333,1.198 0.313,0.198 10 false *2 0.01,1.167 0.323,1.365 0.313,0.198 10 false *1 0.021,1.344 0.333,1.542 0.313,0.198 10 false *2 0.021,1.552 0.333,1.75 0.313,0.198 10 false *1
*1 No. 1 Brake Plate
*2 No. 1 Brake Disc
*3 No. 1 Brake Flange


a.

Install the 3 No. 1 brake plates, 3 No. 1 brake discs and No. 1 brake flange.

NOTICE:
·

Make sure that the No. 1 brake discs, No. 1 brake plates and No. 1 brake flange are installed in the correct order.

·

Install the thicker No. 1 brake plate, and then install the thinner one.




Hide 35624 24.INSTALL 2ND BRAKE PISTON

a.
C324115C01
1.75,0.625 1.75,0.292 1.75,0.292 1.917,0.292 true 1.302,1.333 1.302,1 1.302,1 1.469,1 true 1.948,0.219 2.26,0.417 0.313,0.198 10 false *1 1.531,0.927 1.844,1.125 0.313,0.198 10 false *1
*1 O-ring


Coat 2 new O-rings with ATF, and install them to the 2nd brake piston.


b.

Press the 2nd brake piston into the 2nd brake cylinder.

NOTICE:

Be careful not to damage the 2 O-rings.



c.
C324113C01
2.5,0.5 2.667,0.167 2.667,0.167 2.833,0.167 true 1.552,1.354 1.885,0.688 1.885,0.688 2.052,0.688 true 2.875,0.083 3.333,0.281 0.458,0.198 10 false SST 2.115,0.615 2.573,0.813 0.458,0.198 10 false *a
*a Protective Tape


Using SST, a screwdriver and a press, install the No. 3 brake piston return spring sub-assembly with the snap ring.

SST
09351-40010  (09351-04060, 09351-04070)

NOTICE:
·

Be sure that the end gap of the snap ring is not aligned with the spring retainer claw.

·

Be careful not to damage the 2nd brake cylinder.



HINT:

Tape the screwdriver tip before use.



Hide 35664 25.INSTALL 2ND BRAKE CYLINDER

a.
C324112

Install the 2nd brake cylinder to the automatic transmission case sub-assembly.


b.
C324198

Check that the oil pressure apply hole of the brake cylinder aligns with the oil pressure apply hole of the automatic transmission case sub-assembly.


c.
C324111N01
2.99,1.406 2.99,1.198 2.99,1.198 2.125,0.531 true 2.844,1.438 3.302,1.635 0.458,0.198 10 true SST

Using SST, install the snap ring.

SST
09350-30020  (09350-07060)


Hide 35790 26.INSTALL ONE-WAY CLUTCH ASSEMBLY

C324110

a.

Install the one-way clutch assembly and No. 1 planetary carrier thrust washer to the automatic transmission case sub-assembly.


Hide 27.INSTALL NO. 3 BRAKE DISC

a.
C324199C01
0.344,0.323 0.594,0.323 false 0.323,0.49 0.573,0.49 false 0.323,0.656 0.573,0.656 false 0.313,0.792 0.563,0.792 false 0.344,0.948 0.594,0.948 false 0.313,1.115 0.563,1.115 false 0.333,1.26 0.583,1.26 false 0.323,1.396 0.573,1.396 false 0.333,1.573 0.583,1.573 false 0.313,1.719 0.563,1.719 false 0.188,0.229 0.5,0.427 0.313,0.198 10 false *4 0.156,0.406 0.469,0.604 0.313,0.198 10 false *3 0.156,0.563 0.469,0.76 0.313,0.198 10 false *2 0.156,0.708 0.469,0.906 0.313,0.198 10 false *3 0.167,0.854 0.479,1.052 0.313,0.198 10 false *2 0.167,1.021 0.479,1.219 0.313,0.198 10 false *3 0.167,1.167 0.479,1.365 0.313,0.198 10 false *2 0.167,1.313 0.479,1.51 0.313,0.198 10 false *3 0.167,1.49 0.479,1.688 0.313,0.198 10 false *2 0.156,1.635 0.469,1.833 0.313,0.198 10 false *1
*1 Brake Cushion Plate
*2 No. 3 Brake Plate
*3 No. 3 Brake Disc
*4 No. 3 Brake Flange


Install the break cushion plate, 4 No. 3 brake plates, 4 No. 3 brake discs and No. 3 brake flange to the case.

NOTICE:
·

Make sure that the brake cushion plate, No. 3 brake discs, No. 3 brake plates and No. 3 brake flange are installed in the correct order.

·

Install the thicker brake cushion plate, and then install the thinner one.




b.
C324109C01
1.917,0.865 2.177,0.865 false 2.229,0.781 2.542,0.979 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, install the snap ring.

CAUTION:

Be careful not to damage the automatic transmission case sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35606A 28.INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY

C324108C01
1.99,1.635 1.99,1.365 false 2.719,1.667 2.719,1.417 false 2.667,1.719 2.979,1.917 0.313,0.198 10 false *1 1.927,1.688 2.24,1.885 0.313,0.198 10 false *1
*1 O-ring


a.

Coat 2 new O-rings with ATF, and install them in the direct clutch piston sub-assembly.


b.
C324107C01
2.615,1.75 2.781,1.75 2.781,1.75 2.781,1.417 false 1.344,0.365 1.51,0.365 1.51,0.365 1.51,0.615 false 0.417,0.594 0.583,0.594 0.583,0.594 0.583,0.844 false 2.448,1.677 2.76,1.875 0.313,0.198 10 false *1 1.177,0.292 1.49,0.49 0.313,0.198 10 false *2 0.26,0.521 0.573,0.719 0.313,0.198 10 false *3
*1 Direct Clutch Piston Sub-assembly
*2 Direct Clutch Return Spring Sub-assembly
*3 No. 2 Clutch Balancer


Install the No. 2 clutch balancer and direct clutch return spring sub-assembly to the direct clutch piston sub-assembly.


c.

Press the direct clutch piston sub-assembly into the reverse clutch drum sub-assembly by hands.

NOTICE:

Be careful not to damage the 2 O-rings.



d.
C324200N01
0.531,1.417 1.5,1.417 true 0.667,1.417 1.542,1 true 0.229,1.344 0.688,1.542 0.458,0.198 10 false SST

Place SST on the No. 2 clutch balancer , and compress the direct clutch return spring sub-assembly with a press.

SST
09320-89010  

NOTICE:

Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.



e.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:
·

Be sure that the end gap of the snap ring is not aligned with the spring retainer claw.

·

Do not expand the snap ring excessively.




f.
C324262C01
0.333,1 1.167,1 true 2.26,1 3.083,1 true 0.167,0.917 0.479,1.115 0.313,0.198 10 false *a 3.125,0.927 3.354,1.177 0.229,0.25 10 false *a
*a Stopper


Install the snap ring so that the outside line fits against the stopper of the No. 2 clutch balancer as shown in the illustration.


Hide 35048 29.INSTALL REVERSE CLUTCH PISTON SUB-ASSEMBLY

a.
C324104C01
0.729,1.073 0.729,0.823 0.729,0.823 0.896,0.823 false 0.958,0.74 1.271,0.938 0.313,0.198 10 false *1
*1 O-ring


Coat a new O-ring with ATF, and install it to the reverse clutch drum sub-assembly.


b.
C324103C01
2.573,1.656 2.74,1.656 2.74,1.656 2.74,1.406 false 2.396,1.583 2.708,1.781 0.313,0.198 10 false *1
*1 O-ring


Coat a new O-ring with ATF, and install it to the reverse clutch piston sub-assembly.


c.
C324102C01
0.635,0.771 0.635,0.271 0.635,0.271 0.802,0.271 false 2.573,1.417 2.573,1.75 2.573,1.75 2.406,1.75 false 0.854,0.188 1.167,0.385 0.313,0.198 10 false *1 2.229,1.667 2.542,1.865 0.313,0.198 10 false *2
*1 Reverse Clutch Piston Sub-assembly
*2 Clutch Drum


Press the clutch drum into the reverse clutch piston sub-assembly with both hands.

NOTICE:

Do not damage the O-rings.



Hide 35047 30.INSTALL REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C324101C01
0.646,0.865 0.646,0.615 0.646,0.615 0.479,0.615 false 1.448,0.667 1.448,0.417 1.448,0.417 1.281,0.417 false 2.385,1.573 2.385,1.823 2.385,1.823 2.219,1.823 false 0.323,0.552 0.635,0.75 0.313,0.198 10 false *1 1.104,0.344 1.417,0.542 0.313,0.198 10 false *2 2.042,1.75 2.354,1.948 0.313,0.198 10 false *3
*1 Reverse Clutch Return Spring Sub-assembly
*2 O-ring
*3 Reverse Clutch Piston Sub-assembly


Coat a new O-ring with ATF, and install it to the reverse clutch piston sub-assembly.


b.

Install the reverse clutch return spring sub-assembly onto the reverse clutch piston sub-assembly.


Hide 35688 31.INSTALL NO. 3 CLUTCH BALANCER

a.

Install the No. 3 clutch balancer to the reverse clutch return spring sub-assembly.


b.
C324100N01
1.667,0.917 2.5,0.333 2.5,0.333 2.75,0.333 true 2.083,0.917 2.5,0.333 true 2.792,0.271 3.25,0.469 0.458,0.198 10 false SST

Place SST on the No. 3 clutch balancer, and compress the No. 3 clutch balancer with a press.

SST
09387-00070  

NOTICE:

Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.



c.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:
·

Be sure that the end gap of the snap ring is not aligned with the spring retainer claw.

·

Do not expand the snap ring excessively.




d.
C324201C01
0.646,2.354 0.646,2.021 0.646,2.021 0.813,2.021 false 0.844,1.01 0.844,0.594 0.844,0.594 1.01,0.594 false 0.188,0.417 0.5,0.615 0.313,0.198 10 false *a 0.188,1.802 0.5,2 0.313,0.198 10 false *b 0.854,1.948 1.167,2.146 0.313,0.198 10 false *1 1.073,0.51 1.385,0.708 0.313,0.198 10 false *1
*1 Snap Ring
*a Correct
*b Incorrect


Set the end gap of the snap ring in the piston as shown in the illustration.

NOTICE:

Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



Hide 35667A 32.INSTALL DIRECT CLUTCH DISC

a.
C324263C01
1.01,0.479 1.26,0.479 false 1.031,0.677 1.281,0.677 false 1,0.833 1.25,0.833 false 1.031,1.042 1.281,1.042 false 1,1.208 1.25,1.208 false 1.042,1.417 1.292,1.417 false 1.021,1.583 1.271,1.583 false 1.031,1.781 1.281,1.781 false 1,1.958 1.25,1.958 false 1.031,2.146 1.281,2.146 false 1,2.323 1.25,2.323 false 1.042,2.521 1.292,2.521 false 1.01,2.75 1.26,2.75 false 0.844,0.406 1.156,0.604 0.313,0.198 10 false *3 0.844,0.583 1.156,0.781 0.313,0.198 10 false *2 0.844,0.75 1.156,0.948 0.313,0.198 10 false *1 0.865,0.969 1.177,1.167 0.313,0.198 10 false *2 0.844,1.135 1.156,1.333 0.313,0.198 10 false *1 0.865,1.344 1.177,1.542 0.313,0.198 10 false *2 0.854,1.5 1.167,1.698 0.313,0.198 10 false *1 0.854,1.688 1.167,1.885 0.313,0.198 10 false *2 0.844,1.854 1.156,2.052 0.313,0.198 10 false *1 0.865,2.052 1.177,2.25 0.313,0.198 10 false *2 0.844,2.24 1.156,2.438 0.313,0.198 10 false *1 0.865,2.438 1.177,2.635 0.313,0.198 10 false *2 0.854,2.656 1.167,2.854 0.313,0.198 10 false *1
*1 Clutch Plate
*2 Direct Clutch Disc
*3 Direct Clutch Flange


Install the 6 clutch plates, 6 direct clutch discs and direct clutch flange to the clutch drum.

Install in order:

*1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *3


NOTICE:
·

Make sure that the clutch plates, direct clutch discs and direct clutch flange are installed in the correct order.

·

Install the clutch plate, and then install the thinner one.




b.
C324099C01
2.094,0.688 2.323,0.396 2.323,0.396 2.531,0.396 false 2.583,0.302 2.896,0.5 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, install the 2 snap rings on the clutch drum.

NOTICE:

Be careful not to damage the clutch drum.


HINT:

Tape the screwdriver tip before use.



Hide 35649 34.INSTALL REVERSE CLUTCH FLANGE

a.
C324098

Install the reverse clutch flange to the clutch drum.

NOTICE:

Install the flange that is 3 mm thick.



Hide 35659 35.INSTALL REVERSE CLUTCH REACTION SLEEVE

C324264C01
1.417,0.521 1.667,0.521 false 1.365,1.208 1.615,1.208 false 1.417,1.479 1.667,1.479 false 0.281,1.75 0.531,1.75 false 0.25,2 0.5,2 false 0.281,2.281 0.531,2.281 false 0.24,2.542 0.49,2.542 false 0.281,2.823 0.531,2.823 false 0.25,3.042 0.5,3.042 false 0.281,3.333 0.531,3.333 false 0.24,3.583 0.49,3.583 false 0.281,3.875 0.531,3.875 false 1.708,0.427 2.021,0.625 0.313,0.198 10 false *5 1.677,1.125 1.99,1.323 0.313,0.198 10 false *4 1.708,1.385 2.021,1.583 0.313,0.198 10 false *3 0.115,1.667 0.427,1.865 0.313,0.198 10 false *1 0.083,1.917 0.396,2.115 0.313,0.198 10 false *2 0.125,2.198 0.438,2.396 0.313,0.198 10 false *1 0.073,2.458 0.385,2.656 0.313,0.198 10 false *2 0.115,2.74 0.427,2.938 0.313,0.198 10 false *1 0.083,2.958 0.396,3.156 0.313,0.198 10 false *2 0.115,3.25 0.427,3.448 0.313,0.198 10 false *1 0.083,3.5 0.396,3.698 0.313,0.198 10 false *2 0.115,3.781 0.427,3.979 0.313,0.198 10 false *1
*1 Reverse Clutch Disc
*2 Clutch Plate
*3 Reverse Clutch Flange
*4 Clutch Cushion Plate
*5 Reverse Clutch Reaction Sleeve


a.

Install the 5 reverse clutch discs, 4 clutch plates, reverse clutch flange, clutch cushion plate and reverse clutch reaction sleeve to the reverse clutch piston sub-assembly.

Install in order:

*1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *1 - *3 - *4 - *5


NOTICE:
·

Make sure that the reverse clutch discs, clutch plates, reverse clutch flange, clutch cushion plate and reverse clutch reaction sleeve are installed in the correct order.

·

Install the reverse clutch disc, and then install the thinner one.




b.

Using a screwdriver, install the snap ring.

NOTICE:

Be careful not to damage the reverse clutch piston sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35659 37.REMOVE REVERSE CLUTCH REACTION SLEEVE

C324202C01
2.604,0.667 2.854,0.667 false 2.896,0.583 3.208,0.781 0.313,0.198 10 false *a
*a Protective Tape


a.

Using a screwdriver, remove the snap ring from the clutch drum.

NOTICE:

Be careful not to damage the reverse clutch drum sub-assembly and reverse clutch sleeve.


HINT:

Tape the screwdriver tip before use.



b.
C324203

Remove the reverse clutch reaction sleeve, clutch cushion plate, reverse clutch flange, 5 reverse clutch discs, and 4 clutch plates from the reverse clutch piston sub-assembly.


Hide 35612B 38.INSTALL FORWARD CLUTCH PISTON

C324097C01
0.469,1.417 0.469,1.167 0.469,1.167 0.302,1.167 false 2.719,1.24 2.719,1.49 2.719,1.49 2.885,1.49 false 0.146,1.083 0.458,1.281 0.313,0.198 10 false *1 2.948,1.406 3.26,1.604 0.313,0.198 10 false *1
*1 O-ring


a.

Coat 2 new O-rings with ATF, and install them to the forward clutch piston.


b.

Install the forward clutch piston to the input shaft assembly.

NOTICE:

Be careful not to damage the 2 O-rings.



Hide 35668 39.INSTALL NO. 1 CLUTCH BALANCER

C324095C01
0.792,0.281 0.958,0.281 0.958,0.281 0.958,0.531 false 0.635,0.208 0.948,0.406 0.313,0.198 10 false *1
*1 O-ring


a.

Coat a new O-ring with ATF and install it to the clutch balancer.


b.
C324094C01
0.333,0.458 0.5,0.458 false 0.448,1.167 0.615,1.167 false 0.167,0.385 0.479,0.583 0.313,0.198 10 false *1 0.271,1.094 0.583,1.292 0.313,0.198 10 false *2
*1 No. 1 Clutch Balancer
*2 Forward Clutch Return Spring Sub-assembly


Install the No. 1 clutch balancer and forward clutch return spring assembly.

NOTICE:

Be careful not to damage the O-ring.



c.
D031412N03
1.635,0.385 2.417,0.385 2.417,0.385 2.177,0.625 true 2.479,0.271 2.875,0.521 0.396,0.25 10 false SST

Place SST on the No. 1 clutch balancer, and compress the return spring assembly with a press.

SST
09350-30020  (09350-07040)

NOTICE:

Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0393 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.



d.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:

Do not expand the snap ring excessively.



e.
C109354C02
0.885,0.51 0.781,0.51 0.781,0.51 0.781,0.979 false 0.688,1.927 0.625,1.927 0.625,1.927 0.625,2.406 false 0.927,0.417 1.167,0.635 0.24,0.219 10 false *1 0.271,0.448 0.438,0.646 0.167,0.198 10 false *a 0.729,1.833 0.948,2.052 0.219,0.219 10 false *1 0.271,1.885 0.469,2.083 0.198,0.198 10 false *b
*1 Snap Ring
*a Correct
*b Incorrect


Set the end gap of the snap ring in the No. 1 clutch balancer as shown in the illustration.


Hide 35633B 40.INSTALL FORWARD MULTIPLE DISC CLUTCH DISC

a.
C324267C01
2.188,0.385 2.438,0.385 false 2.167,0.573 2.417,0.573 false 2.188,0.76 2.438,0.76 false 2.167,0.969 2.417,0.969 false 2.188,1.156 2.438,1.156 false 2.167,1.354 2.417,1.354 false 2.188,1.531 2.438,1.531 false 2.156,1.75 2.406,1.75 false 2.177,1.927 2.427,1.927 false 2.167,2.146 2.417,2.146 false 2.188,2.323 2.438,2.323 false 2.167,2.531 2.417,2.531 false 2.188,2.698 2.438,2.698 false 2.167,2.885 2.417,2.885 false 2.188,3.063 2.438,3.063 false 2.479,0.292 2.792,0.49 0.313,0.198 10 false *1 2.479,0.5 2.792,0.698 0.313,0.198 10 false *2 2.479,0.688 2.792,0.885 0.313,0.198 10 false *3 2.448,0.885 2.76,1.083 0.313,0.198 10 false *2 2.448,1.083 2.76,1.281 0.313,0.198 10 false *3 2.458,1.271 2.771,1.469 0.313,0.198 10 false *2 2.469,1.458 2.781,1.656 0.313,0.198 10 false *3 2.448,1.688 2.76,1.885 0.313,0.198 10 false *2 2.458,1.854 2.771,2.052 0.313,0.198 10 false *3 2.458,2.073 2.771,2.271 0.313,0.198 10 false *2 2.49,2.25 2.802,2.448 0.313,0.198 10 false *3 2.458,2.448 2.771,2.646 0.313,0.198 10 false *2 2.479,2.625 2.792,2.823 0.313,0.198 10 false *3 2.469,2.802 2.781,3 0.313,0.198 10 false *2 2.479,2.979 2.792,3.177 0.313,0.198 10 false *1
*1 Forward Clutch Flange
*2 Forward Multiple Disc Clutch Disc
*3 Clutch Plate


Install the 2 forward clutch flanges, 7 forward multiple disc clutch discs and 6 clutch plates to the input shaft assembly.

NOTICE:
·

Make sure that the forward clutch flanges, forward multiple disc clutch discs and clutch plates are installed in the correct order.

·

Install the forward clutch flange, and then install the thinner one.

·

If the forward clutch flanges have different thicknesses, first install the thinner flange.




b.
C324092C01
0.917,0.573 1.292,0.573 false 0.74,0.479 1.052,0.677 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, install the snap ring.

NOTICE:

Be careful not to damage the input shaft.


HINT:

Tape the screwdriver tip before use.



Hide 35712A 41.INSTALL INPUT SHAFT OIL SEAL RING

a.

Coat 3 new input shaft oil seal rings with ATF.


b.
C284160

Squeeze the ends of the 3 input shaft oil seal rings together, and then install them to the input shaft groove.

NOTICE:

Do not excessively widen the input shaft oil seal ring.


HINT:

After installing the input shaft oil seal rings, check that they rotate smoothly.



Hide 35701 43.INSTALL INPUT SHAFT ASSEMBLY

a.
C324091

Install the input shaft assembly to the clutch drum.


b.
C324090

Coat the thrust needle roller bearing with ATF and Install it to the clutch drum.

Thrust Needle Roller Bearing Diameter:
Item Inside Outside
Thrust needle roller bearing
(Thrust bearing C)
21.3 mm (0.839 in.) 41.1 mm (1.62 in.)



Hide 35631 44.INSTALL MULTIPLE DISC CLUTCH HUB

a.
C324089C01
2.917,1.5 2.917,1.167 false 0.5,1.031 0.5,0.781 0.5,0.781 0.667,0.781 false 2.844,1.521 3.156,1.719 0.313,0.198 10 false *1 0.708,0.698 1.021,0.896 0.313,0.198 10 false *2
*1 No. 3 Thrust Bearing Race
(Rear Race C)
*2 No. 4 Thrust Bearing Race
(Front Race D)


Coat the No. 3 thrust bearing race and No. 4 thrust bearing race with ATF and install them to the multiple disc clutch hub.

Thrust Bearing Race Diameter:
Item Inside Outside
No. 3 thrust bearing race
(Rear race C)
22.6 mm (0.890 in.) 45.0 mm (1.77 in.)
No. 4 thrust bearing race
(Front race D)
38.4 mm (1.51 in.) 56.5 mm (2.22 in.)



b.
C324088

Install the multiple disc clutch hub to the reverse clutch piston sub-assembly.


Hide 35061 45.INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY

a.
C324087C01
0.448,1.156 0.448,0.823 0.448,0.823 0.615,0.823 false 2.927,1.052 2.927,1.385 2.927,1.385 2.76,1.385 false 0.677,0.74 0.99,0.938 0.313,0.198 10 false *2 2.594,1.313 2.906,1.51 0.313,0.198 10 false *1
*1 Thrust Needle Roller Bearing
(Thrust Bearing D)
*2 Thrust Needle Roller Bearing
(Thrust Bearing E)


Coat the 2 thrust needle roller bearings with ATF, and install them to the forward clutch hub sub-assembly.

Thrust Needle Roller Bearing Diameter:
Item Inside Outside
Thrust needle roller bearing
(Thrust bearing D)
33.3 mm (1.31 in.) 51.5 mm (2.02 in.)
Thrust needle roller bearing
(Thrust bearing E)
42.5 mm (1.67 in.) 61.2 mm (2.41 in.)



b.
C324086

Install the forward clutch hub sub-assembly to the reverse clutch piston sub-assembly.


Hide 35677C 46.INSTALL REVERSE CLUTCH DISC

a.
C324204C01
1.354,0.281 1.438,0.198 1.438,0.198 1.604,0.198 false 1.417,0.552 1.615,0.552 false 1.427,0.802 1.625,0.802 false 1.438,1.042 1.635,1.042 false 1.427,1.292 1.625,1.292 false 1.427,1.542 1.625,1.542 false 0.302,1.75 0.5,1.75 false 0.302,1.5 0.5,1.5 true 0.302,1.25 0.5,1.25 true 0.302,1 0.5,1 true 0.302,0.75 0.5,0.75 true 1.646,0.125 1.958,0.323 0.313,0.198 10 false *4 1.667,0.49 1.979,0.688 0.313,0.198 10 false *3 1.667,0.729 1.979,0.927 0.313,0.198 10 false *2 1.667,0.969 1.979,1.167 0.313,0.198 10 false *2 1.667,1.208 1.979,1.406 0.313,0.198 10 false *2 1.667,1.469 1.979,1.667 0.313,0.198 10 false *2 0.167,1.667 0.479,1.865 0.313,0.198 10 false *1 0.167,1.417 0.479,1.615 0.313,0.198 10 false *1 0.167,1.167 0.479,1.365 0.313,0.198 10 false *1 0.167,0.917 0.479,1.115 0.313,0.198 10 false *1 0.167,0.667 0.479,0.865 0.313,0.198 10 false *1
*1 Reverse Clutch Disc
*2 Clutch Plate
*3 Reverse Clutch Flange
*4 Clutch Cushion Plate


Install the 5 reverse clutch discs, 4 clutch plates, reverse clutch flange and clutch cushion plate to the reverse clutch hub sub-assembly.

NOTICE:
·

Make sure that the reverse clutch discs, clutch plates, reverse clutch flange and clutch cushion plate are installed in the correct order.




Hide 35659 47.INSTALL REVERSE CLUTCH REACTION SLEEVE

a.
C324085

Install the reverse clutch reaction sleeve to the reverse clutch hub sub-assembly.


Hide 35049 48.INSTALL REVERSE CLUTCH HUB SUB-ASSEMBLY

a.
C324084

Install the reverse clutch hub sub-assembly to the reverse clutch piston sub-assembly.


b.
C324083C01
2.573,0.938 2.896,0.938 false 2.927,0.844 3.24,1.042 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, install the snap ring to the clutch drum and input shaft assembly.

NOTICE:

Be careful not to damage the reverse clutch piston sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35780B 49.INSTALL NO. 2 ONE-WAY CLUTCH ASSEMBLY

a.
C324081C01
2.698,0.135 2.865,0.135 2.865,0.135 2.865,0.385 false 2.375,1.271 2.375,1.521 2.375,1.521 2.542,1.521 false 1.229,0.365 1.396,0.365 1.396,0.365 1.396,0.615 false 2.542,0.052 2.854,0.25 0.313,0.198 10 false *1 2.604,1.448 2.917,1.646 0.313,0.198 10 false *2 1.073,0.313 1.385,0.51 0.313,0.198 10 false *3
*1 No. 2 One-way Clutch Assembly
*2 No. 2 Clutch Drum Thrust Washer
*3 Reverse Clutch Piston sub-assembly


Install the No. 2 one-way clutch assembly and No. 2 clutch drum thrust washer to the reverse clutch piston sub-assembly.

NOTICE:

Be sure to install the No. 2 clutch drum thrust washer in the correct direction.



Hide 50.INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

C324268C01
0.302,1.208 0.302,0.792 0.302,0.792 0.469,0.792 false 0.719,1.604 0.719,1.854 0.719,1.854 0.885,1.854 false 3.073,0.479 3.073,0.313 3.073,0.313 2.906,0.313 false 0.552,0.719 0.865,0.917 0.313,0.198 10 false *1 0.938,1.792 1.25,1.99 0.313,0.198 10 false *2 2.75,0.24 3.063,0.438 0.313,0.198 10 false *3
*1 Thrust Needle Roller Bearing
(Thrust Bearing A)
*2 Thrust Needle Roller Bearing
(Thrust Bearing B)
*3 Clutch Drum Thrust Washer


a.

Coat the 2 thrust needle roller bearings and clutch drum thrust washer with ATF and install them to the reverse clutch piston sub-assembly.

Thrust Needle Roller Bearing Diameter:
Item Inside Outside
Thrust needle roller bearing
(Thrust bearing A)
71.9 mm (2.83 in.) 85.6 mm (3.37 in.)
Thrust needle roller bearing
(Thrust bearing B)
34.6 mm (1.36 in.) 52.0 mm (2.05 in.)



b.
C324349

Install the reverse clutch piston sub-assembly to the automatic transmission case sub-assembly.


Hide 51.INSTALL OIL PUMP ASSEMBLY

C324350C01
1.135,0.927 1.135,0.677 1.135,0.677 1.302,0.677 false 0.604,1.25 0.604,1 0.604,1 0.438,1 false 1.354,0.594 1.667,0.792 0.313,0.198 10 false *1 0.26,0.917 0.573,1.115 0.313,0.198 10 false *2
*1 No. 1 Thrust Bearing Race
(Front Race A)
*2 No. 2 Thrust Bearing Race
(Front Race B)


a.

Coat the No. 1 thrust bearing race and No. 2 thrust bearing race with ATF, and install them to the oil pump assembly.

Thrust Bearing Race Diameter:
Item Inside Outside
No. 1 thrust bearing race
(Front race A)
74.2 mm (2.92 in.) 87.74 mm (3.45 in.)
No. 2 Thrust bearing race
(Front race B)
37.0 mm (1.46 in.) 52.3 mm (2.06 in.)



b.
C324206C01
2.552,0.5 2.719,0.25 2.719,0.25 2.885,0.25 false 2.958,0.167 3.271,0.365 0.313,0.198 10 false *1
*1 O-ring


Coat a new O-ring with ATF, and install it to the oil pump assembly.


c.

Clean the bolt and the bolt hole.


d.

Place the oil pump assembly through the input shaft, and align the bolt holes of the oil pump assembly with the automatic transmission case sub-assembly.


e.

Hold the input shaft assembly, and lightly press the oil pump assembly to slide the input shaft oil seal rings into the reverse clutch piston sub-assembly.

NOTICE:

Do not excessively push on the oil pump assembly, as the input shaft oil seal ring will stick to the clutch drum.



f.

Apply adhesive to 2 or 3 threads on the end of the 10 bolts.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



g.

Install the 10 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 35506F 52.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

a.

Coat the manual valve lever shaft oil seal lips with MP grease.


b.
C210165C02
1.75,1.833 1.75,2.427 false 1.385,4.042 1.385,4.396 false 0.167,0.135 0.365,0.333 0.198,0.198 10 false *a 0.167,2.469 0.365,2.667 0.198,0.198 10 false *b 1.604,2.458 1.927,2.656 0.323,0.198 10 true SST 1.25,4.427 1.604,4.615 0.354,0.188 10 true SST
*a RH Side
*b LH Side


Using SST and a hammer, drive in 2 new manual valve lever shaft oil seals.

SST
09350-30020  (09350-07110)

Oil seal drive in depth:

-0.3 to 0.3 mm (-0.0118 to 0.0118 in.)



Hide 35505 54.INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

C324207C01
1.042,1.094 1.042,0.844 1.042,0.844 1.208,0.844 false 0.833,0.698 0.833,0.448 0.833,0.448 1,0.448 false 1.25,0.76 1.563,0.958 0.313,0.198 10 false *1 1.042,0.365 1.354,0.563 0.313,0.198 10 false *2
*1 Spacer
*2 Manual Valve Lever Sub-assembly


a.

Install a new spacer to the manual valve lever sub-assembly.


b.

Push the manual valve lever shaft through the automatic transmission case sub-assembly, and install the manual valve lever sub-assembly to the manual valve lever shaft.


c.
C324208

Using a hammer, tap in a new spring pin.


d.
C324209

Align the manual valve lever indentation with the spacer hole, and stake them together with a punch.


e.

Check that the shaft rotates smoothly.


Hide 35556 55.INSTALL PARKING LOCK PAWL SHAFT

C324073C01
0.667,0.667 0.833,0.667 0.833,0.667 1,0.333 true 2.375,0.76 2.667,0.333 2.667,0.333 2.833,0.333 true 2.385,0.938 2.635,0.938 2.635,0.938 2.802,0.938 true 2.417,1.583 2.667,1.583 2.667,1.583 2.917,1.583 true 0.5,0.583 0.729,0.771 0.229,0.188 10 true *1 2.875,0.25 3.104,0.438 0.229,0.188 10 true *2 2.844,0.844 3.073,1.031 0.229,0.188 10 true *3 2.958,1.5 3.188,1.688 0.229,0.188 10 true *4
*1 Parking Lock Pawl
*2 E-ring
*3 Parking Lock Pawl Shaft
*4 Spring


a.

Install a new E-ring to the shaft.


b.

Install the parking lock pawl, parking lock pawl shaft and spring.


Hide 35501 56.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

C324072

a.

Connect the parking lock rod sub-assembly to the manual valve lever sub-assembly as shown in the illustration.


Hide 35595 57.INSTALL PARKING LOCK PAWL BRACKET

a.
C324071

Place the parking lock pawl bracket onto the automatic transmission case sub-assembly and tighten the 3 bolts.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


b.
C324210C01
2.427,0.188 2.594,0.188 2.594,0.188 2.927,0.188 true 0.729,0.969 0.896,0.969 0.896,0.969 0.896,1.302 true 0.698,1.771 0.865,1.771 0.865,1.771 0.865,1.604 false 2.271,0.125 2.583,0.323 0.313,0.198 10 false *1 0.563,0.906 0.875,1.104 0.313,0.198 10 false *2 0.531,1.698 0.844,1.896 0.313,0.198 10 false *3
*1 Manual Valve Lever Sub-assembly
*2 Planetary Ring Gear
*3 Parking Lock Pawl


Shift the manual valve lever sub-assembly to the P, and confirm that the planetary gear is correctly locked up by the parking lock pawl.


Hide 35424F 58.INSTALL C-1 ACCUMULATOR VALVE

C324070C01
1.719,0.583 1.948,0.135 1.948,0.135 2.146,0.135 true 1.031,1.031 0.75,1.5 0.75,1.5 0.583,1.5 true 0.406,1.417 0.719,1.615 0.313,0.198 10 false *1 2.177,0.073 2.49,0.271 0.313,0.198 10 false *2
*1 Outer Spring
*2 Inner Spring


a.

Install the 2 springs and C-1 accumulator valve to the hole.

C-1 Accumulator Spring:
Inner Spring
Free Length Outer Diameter Color
30.40 mm (1.20 in.) 11.40 mm (0.449 in.) Pink

Outer Spring
Free Length Outer Diameter Color
48.76 mm (1.92 in.) 16.60 mm (0.654 in.) Light green



Hide 35426D 59.INSTALL C-3 ACCUMULATOR PISTON

C324351C01
1.167,0.667 1.333,0.667 1.333,0.667 1.646,0.958 false 2.688,0.594 2.917,0.594 false 0.667,0.917 0.833,0.917 0.833,0.917 1.656,1.479 true 2.688,0.354 2.917,0.354 2.917,0.354 2.917,0.833 false 0.99,0.583 1.302,0.781 0.313,0.198 10 false *1 0.521,0.833 0.75,1.042 0.229,0.208 10 false *2 2.854,0.875 3.083,1.083 0.229,0.208 10 false *3
*1 Outer Spring
*2 Inner Spring
*3 O-ring


a.

Coat 2 new O-rings with ATF, and install them to the C-3 accumulator piston.


b.

Install the 2 springs and C-3 accumulator piston to the hole.

C-3 Accumulator Spring:
Inner Spring
Free Length Outer Diameter Color
44.0 mm (1.73 in.) 14.0 mm (0.551 in.) Yellow

Outer Spring
Free Length Outer Diameter Color
73.35 mm (2.89 in.) 19.90 mm (0.783 in.) Red



Hide 35427K 60.INSTALL B-3 ACCUMULATOR PISTON

C324352C01
1.354,0.74 1.583,0.74 1.583,0.74 1.99,1.042 false 3.042,0.5 3.208,0.5 3.208,0.5 3.208,1 false 3.031,0.75 3.198,0.75 false 1.188,0.667 1.5,0.865 0.313,0.198 10 false *2 3.135,1.031 3.396,1.281 0.26,0.25 10 false *1
*1 O-ring
*2 Spring


a.

Coat 2 new O-rings with ATF, and install them to the piston.


b.

Install the spring and B-3 accumulator piston to the hole.

B-3 Accumulator Spring:
Free Length Outer Diameter Color
70.5 mm (2.78 in.) 19.7 mm (0.776 in.) Purple



Hide 35425A 61.INSTALL C-2 ACCUMULATOR PISTON

C324353C01
1.656,0.656 1.823,0.656 1.823,0.656 2.156,1.073 false 2.802,1.104 2.802,0.469 2.802,0.469 2.969,0.469 false 2.802,0.708 2.979,0.708 false 1.49,0.583 1.802,0.781 0.313,0.198 10 false *1 2.75,1.135 3.063,1.333 0.313,0.198 10 false *2
*1 Spring
*2 O-ring


a.

Coat 2 new O-rings with ATF, and install them to the piston.


b.

Install the spring and C-2 accumulator piston to the hole.

C-2 Accumulator Spring:
Free Length Outer Diameter Color
62.0 mm (2.44 in.) 15.9 mm (0.626 in.) White



Hide 35251 62.INSTALL CHECK BALL BODY

a.
C324067

Install the spring and check ball body.


Hide 35159 63.INSTALL BRAKE DRUM GASKET

a.
C324066

Install a new 3 brake drum gaskets.


Hide 35145C 64.INSTALL TRANSMISSION CASE GASKET

a.
C324065

Coat 3 new transmission case gaskets with ATF, and install the transmission case gaskets.


Hide 35410 65.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

Hide 35330 67.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

Hide 35106 68.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

a.

Install the automatic transmission oil pan sub-assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TRANSMISSION WIRE>INSTALLATION


b.

Install a new gasket and the drain plug.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Install a new gasket and the overflow plug.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 35157B 69.INSTALL REAR TRANSFER CASE ADAPTER OIL RECEIVER

a.
C190069

Install the transfer case adapter oil receiver to the rear transfer adaptor.


b.

Using snap ring pliers, install the snap ring.


Hide 36117A 70.INSTALL TRANSFER ADAPTER OIL SEAL

C177436N04
1.219,1.031 0.396,1.188 true 0.104,1.115 0.469,1.292 0.365,0.177 10 false SST

a.

Coat the lip of a new transfer adapter oil seal with MP grease.


b.

Using SST and a hammer, tap in a new transfer adapter oil seal.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07150)

Standard depth:

0 to 0.5 mm (0 to 0.0196 in.)



Hide 36107A 71.INSTALL TRANSFER ADAPTER SUB-ASSEMBLY

a.

Clean the threads of the bolts and the automatic transmission case sub-assembly and transfer adapter sub-assembly with non-residue solvent.

NOTICE:

Using a razor blade and gasket scraper, remove all the old seal packing material from the gasket surfaces.



b.
C175554C04
2.021,0.385 2.177,0.167 2.177,0.167 2.302,0.167 false 2.344,0.073 2.573,0.281 0.229,0.208 10 false *a
*a Seal Packing


Apply seal packing to the transfer adapter sub-assembly as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281,

Three Bond 1281 or equivalent


NOTICE:
·

Apply seal packing in a continuous line (width approximately 1.2 mm (0.0472 in.)) along the sealing surface.

·

Parts must be assembled within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.




c.

Apply a few drops of adhesive to 2 or 3 threads of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent



d.
C285751N01
0.615,1.948 0.76,2.125 0.146,0.177 10 false A 0.792,1.271 0.948,1.448 0.156,0.177 10 true B 1.063,1.906 1.219,2.104 0.156,0.198 10 true A 2.271,1.896 2.427,2.094 0.156,0.198 10 true A 2.708,1.938 2.865,2.135 0.156,0.198 10 true A 0.865,0.427 1.021,0.604 0.156,0.177 10 true B 2.469,0.417 2.625,0.615 0.156,0.198 10 true B 2.552,1.24 2.719,1.427 0.167,0.188 10 true B

Install the extension housing sub-assembly with 8 bolts.

Torque:
33.9 N*m (346 kgf*cm, 25 ft.*lbf)

Bolt Length:
Item Length
Bolt A 40 mm (1.57 in.)
Bolt B 50 mm (1.97 in.)



Hide 35111 72.INSTALL AUTOMATIC TRANSMISSION HOUSING

a.

Clean the threads of the bolts and the case with non-residue solvent.


b.
C268495

Install the automatic transmission housing to the automatic transmission case sub-assembly with the 6 bolts.

Torque:
33.9 N*m (346 kgf*cm, 25 ft.*lbf)


c.

Apply a few drops of adhesive to 2 or 3 threads of each of the 4 bolts.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent



d.
C268496N02
2.563,1.656 2.719,1.844 0.156,0.188 10 false B 0.844,1.625 1.042,1.802 0.198,0.177 10 false B 1.156,1.792 1.313,1.969 0.156,0.177 10 true A 2.25,1.802 2.427,1.969 0.177,0.167 10 false A

Install the 4 bolts to the automatic transmission housing.

Torque:
for Bolt A (14 mm head) : 33.9 N*m (346 kgf*cm, 25 ft.*lbf)
for Bolt B (17 mm head) : 56.8 N*m (579 kgf*cm, 42 ft.*lbf)


Hide 35122 73.INSTALL AUTOMATIC TRANSMISSION BREATHER TUBE

a.
C324366C01
0.115,0.427 0.115,0.177 0.115,0.177 0.281,0.177 false 0.906,1.073 0.906,0.823 0.906,0.823 1.073,0.823 false 2.406,1.427 2.406,1.76 2.406,1.76 2.24,1.76 false 3.26,1.594 3.26,1.844 3.26,1.844 3.094,1.844 false 0.333,0.083 0.646,0.281 0.313,0.198 10 false *1 1.115,0.729 1.427,0.927 0.313,0.198 10 false *2 2.052,1.667 2.365,1.865 0.313,0.198 10 false *3 2.927,1.75 3.24,1.948 0.313,0.198 10 false *4
*1 No. 1 Breather Plug
*2 Automatic Transmission Breather Hose
*3 Automatic Transmission Breather Tube
*4 O-ring


Coat a new O-ring with ATF and install it to the automatic transmission breather tube.


b.

Install the No. 1 breather plug and automatic transmission breather hose to the automatic transmission breather tube.


c.
C324247

Install the automatic transmission breather tube with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 89413R 74.INSTALL TRANSMISSION REVOLUTION SENSOR (SP2)

Hide 89413N 75.INSTALL TRANSMISSION REVOLUTION SENSOR (NT)

Hide 76.INSTALL OIL COOLER TUBE UNION

a.

Coat the 2 new O-rings with ATF, and install it to 2 oil cooler tube unions.


b.
C324355C01
2.26,1.396 2.458,1.594 0.198,0.198 10 true *a 2.906,0.531 3.104,0.729 0.198,0.198 10 true *a
*a -18 to -22°


Temporarily install the 2 oil cooler tube unions as shown in the illustration.


c.
C324367C01
1.49,1.698 1.302,1.333 1.302,1.333 1.083,1.333 false 2.146,1.219 2.458,1.417 0.313,0.198 10 false *a 0.802,1.26 1.25,1.458 0.448,0.198 10 false SST 0.802,1.958 1.156,2.156 0.354,0.198 10 false *b
*a Torque Wrench Fulcrum Length
*b Hold


Using a SST, hold the oil cooler tube union and tighten the 2 oil cooler tube unions.

SST
09268-78010  

Specified tightening torque:

29.4 N*m (300 kgf*cm, 22 ft.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 34.5 mm (1.36 in.)) + torque wrench (fulcrum length of 300 mm (11.8 in.)): 26.4 N*m (269 kgf*cm, 19 ft.*lbf)



NOTICE:

After tightening, check that the oil cooler tube union does not move.



Hide 84540 77.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

HINT:

Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.


a.

Clean the bolt and the bolt hole.


b.

Apply adhesive to 2 or 3 threads on the end of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.
C324245

Temporarily install the park/neutral position switch assembly to the automatic transmission case sub-assembly with the bolt.


d.

Install the lock washer. Install and tighten the nut.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


e.
C245255N02
1.396,0.052 1.552,0.25 0.156,0.198 10 true N 1.781,0.042 1.938,0.24 0.156,0.198 10 true R 2.146,0.135 2.302,0.333 0.156,0.198 10 true P

Using the transmission control shaft lever LH, turn the manual lever shaft clockwise until it stops, and then turn it counterclockwise 2 notches to set it to N.


f.
C283078C02
1.979,1.573 2.844,1.573 true 1.969,0.927 2.833,0.927 true 2.885,0.833 3.198,0.99 0.313,0.156 10 false *a 2.885,1.49 3.198,1.646 0.313,0.156 10 false *b
*a Neutral Basic Line
*b Groove


Align the neutral basic line with the switch groove, and tighten the adjusting bolt.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


g.
C324215

Using a screwdriver, bend the tabs of the lock washer.

HINT:

Bend at least 2 of the lock washer tabs.



Hide 35573 78.INSTALL TRANSMISSION CONTROL SHAFT LEVER LH

a.
C324244

Install the transmission control shaft lever LH with the spring washer and nut.

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)