There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
| Symptom | Trouble Area |
|---|---|
|
*1: w/ VSC *2: for Automatic Air Conditioning System or for Manual Air Conditioning System (w/ PTC Heater) *3: w/ Entry and Start System *4: for 4WD *5: w/ Audio and Visual System (for Radio and Display Type) *6: w/ Navigation System *7: for LED Headlight or w/ Headlight Cleaner System *8: w/ Airbag System |
|
| The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω. | ·
Short between CAN bus lines ·
ECM ·
Brake actuator assembly (skid control ECU) ·
Spiral with sensor cable sub-assembly (steering angle sensor)*1 ·
Air conditioning amplifier assembly*2 ·
Airbag sensor assembly*8 ·
Certification ECU (smart key ECU assembly)*3 ·
4 wheel drive control ECU*4 ·
Radio and display receiver assembly*5 ·
Navigation receiver assembly*6 ·
Headlight leveling ECU assembly*7 ·
Combination meter assembly ·
No. 1 CAN junction connector ·
No. 2 CAN junction connector ·
DLC3 CAN branch wire or connector |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.
Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION
Type B:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
When replacing the combination meter assembly, make sure to replace it with a new one.
Before replacing the certification ECU (smart key ECU assembly), refer to the service bulletin.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
| *a | Front view of DLC3 |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 1 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G8-6 (CANH) - G8-14 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of DLC3 |
Disconnect the No. 2 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G8-6 (CANH) - G8-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) |
| *c | to 4 Wheel Drive Control ECU (for 4WD) | *d | to ECM |
| *e | ·
to Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type]) ·
to Navigation Receiver Assembly (w/ Navigation System) |
*f | ·
to Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System) ·
to Air Conditioning Amplifier Assembly (for Manual Air Conditioning System [w/ PTC Heater]) |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*1: w/ Entry and Start System *2: for 4WD *3: w/ Audio and Visual System (for Radio and Display Type) *4: w/ Navigation System *5: for Automatic Air Conditioning System *6: for Manual Air Conditioning System (w/ PTC Heater) |
|||
| G68-3 (CANH) - G68-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Certification ECU (Smart Key ECU Assembly)*1 |
| G68-4 (CANH) - G68-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | 4 Wheel Drive Control ECU*2 |
| G68-5 (CANH) - G68-15 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | ECM |
| G68-7 (CANH) - G68-17 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ·
Radio and Display Receiver Assembly*3 ·
Navigation Receiver Assembly*4 |
| G68-10 (CANH) - G68-20 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Air Conditioning Amplifier Assembly*5, *6 |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to certification ECU [smart key ECU assembly] CAN branch wire) (w/ Entry and Start System) | B |
| NG (to 4 wheel drive control ECU CAN branch wire) (for 4WD) | C |
| NG (to ECM CAN main wire) (for 1TR-FE, 2TR-FE) | D |
| NG (to ECM CAN main wire) (for 1KD-FTV, 2KD-FTV) | E |
| NG (to ECM CAN main wire) (for 1GD-FTV, 2GD-FTV) | F |
| NG (to ECM CAN main wire) (for 5L-E) | G |
| NG (to radio and display receiver assembly CAN branch wire) (w/ Audio and Visual System [for Radio and Display Type]) | H |
| NG (to navigation receiver assembly CAN branch wire) (w/ Navigation System) | I |
| NG (to air conditioning amplifier assembly CAN branch wire) (for Automatic Air Conditioning System) | J |
| NG (to air conditioning amplifier assembly CAN branch wire) (for Manual Air Conditioning System [w/ PTC Heater]) | K |
A
B
C
D
E
F
G
H
I
J
K
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly]) |
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G70-40 (CANH) - G70-18 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to 4 Wheel Drive Control ECU) |
Disconnect the 4 wheel drive control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C39-20 (CANH) - C39-40 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G45-13 (CANH) - G45-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for 1TR-FE:
Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>ECM>REMOVAL
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ECM>REMOVAL
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G83-24 (CANH) - G83-23 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for 1KD-FTV:
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2KD-FTV:
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G85-17 (CANH) - G85-28 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2GD-FTV:
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>REMOVAL
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G121-25 (CANH) - G121-31 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
Disconnect the radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-9 (CANH) - G37-10 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Navigation Receiver Assembly) |
Disconnect the navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G113-9 (CANH) - G113-10 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G33-11 (TX+) - G33-12 (TX-) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G77-8 (TX+) - G77-9 (TX-) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 1 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Brake Actuator Assembly (Skid Control ECU) |
| *c | to Airbag Sensor Assembly (w/ Airbag System) | *d | to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) (w/ VSC) |
| *e | to Combination Meter Assembly | *f | to No. 2 CAN Junction Connector |
| *g | to Headlight Leveling ECU Assembly (for LED Headlight or w/ Headlight Cleaner System) | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*1: w/ VSC *2: for LED Headlight or w/ Headlight Cleaner System *3: w/ Airbag System |
|||
| G67-1 (CANH) - G67-11 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Brake Actuator Assembly (Skid Control ECU) |
| G67-2 (CANH) - G67-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Airbag Sensor Assembly*3 |
| G67-3 (CANH) - G67-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)*1 |
| G67-5 (CANH) - G67-15 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Combination Meter Assembly |
| G67-6 (CANH) - G67-16 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 2 CAN Junction Connector |
| G67-8 (CANH) - G67-18 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Headlight Leveling ECU Assembly*2 |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to brake actuator assembly [skid Control ECU] CAN branch wire) | B |
| NG (to airbag sensor assembly CAN branch wire) (w/ Airbag System) | C |
| NG (to spiral with sensor cable sub-assembly [steering angle sensor] CAN branch wire) (w/ VSC) | D |
| NG (to combination meter assembly CAN main wire) | E |
| NG (to headlight leveling ECU assembly CAN branch wire) (for LED Headlight or w/ Headlight Cleaner System) | F |
| NG (to No. 2 CAN junction connector CAN main wire) | G |
A
B
C
D
E
F
G
Reconnect the No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *A | w/ VSC |
| *B | w/o VSC |
| *a | Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU]) |
Disconnect the brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A4-22 (CANH) - A4-10 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A3-25 (CANH) - A3-14 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
w/ VSC:
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/ VSC)>REMOVAL
w/o VSC:
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/o VSC)>REMOVAL
NG
Reconnect the No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Airbag Sensor Assembly) |
Disconnect the airbag sensor assembly connector.
Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION
Type B:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G42-13 (CANH) - G42-22 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor]) |
Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G21-3 (CANH) - G21-2 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-36 (CANH) - G9-35 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Headlight Leveling ECU Assembly) |
Disconnect the headlight leveling ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G80-6 (CANH) - G80-7 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG