Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2016.01–2016.03
RM3250E _58 Vehicle Interior _038068 METER / GAUGE / DISPLAY _0184171 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Display Malfunction  


DESCRIPTION

OPERATION


The combination meter assembly uses the fuel injection volume signal from the ECM and fuel sender gauge assembly to detect the amount of fuel remaining in the fuel tank sub-assembly. Each gauge assembly has a variable resistor whose resistance changes according to the amount of fuel remaining. The gauge assemblies receive voltage from the combination meter assembly and change the voltage based on the resistance that changes according to the amount of fuel remaining in the fuel tank sub-assembly. The combination meter assembly receives a fuel injection volume signal from the ECM and detects the voltage between each variable resistor and each resistor in the combination meter assembly, and operates the fuel receiver gauge.


FUEL RECEIVER GAUGE READING


a.

During normal driving:

As the fuel level in the fuel tank sub-assembly changes when driving on a hill or applying brakes, the fuel receiver gauge reading is updated according to the fuel injection volume during normal driving. However, as the fuel injection volume measurement has a margin of error, the value is indicated after correction by input values from the fuel sender gauge assembly.


b.

During refueling:

The fuel level in the fuel tank sub-assembly rises rapidly when fuel is added. If the averaging process that is used during normal driving is used in this case, the fuel receiver gauge reading cannot be updated promptly. Therefore, when it is judged that fuel is being added to the vehicle based on the shift lever position and changes in the fuel level, output values from the fuel sender gauge assembly are immediately reflected in the fuel receiver gauge reading. This control is called refueling judgment.



REFUELING JUDGMENT CONDITIONS


NOTICE:

Add fuel with the ignition switch off to ensure safety and to enable refueling judgment so that an appropriate fuel receiver gauge reading is obtained. If it is necessary to add fuel with the ignition switch ON, move the shift lever to P or N.


a.

Normal judgment condition (When normal refueling method is used)

With the ignition switch off, the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level.


b.

Other judgment conditions (When other refueling method is used)

Any of the following conditions is met:

·

With the vehicle and engine stopped and the ignition switch ON, the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level.

·

With the vehicle stopped, the engine running, the ignition switch ON and the shift lever in P or N, the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level.

·

With the vehicle stopped, the engine running, the ignition switch ON and the shift lever in any driving position, the fuel sender gauge assembly detects a change of 15.0 liters (15.9 US qts, 13.2 Imp. qts) or more in the fuel level.




PRECAUTION FOR REFUELING


The fuel sender gauge assembly cannot detect changes in the fuel level within certain ranges (around points E and F). Therefore, even though 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more of fuel is added, refueling judgment may not be performed and the fuel receiver gauge reading may not change when fuel level is within such ranges.


FORCED RESET OF FUEL RECEIVER GAUGE


When driving at 20 km/h (12 mph) or more, if the output values from the fuel sender gauge assembly are different from the fuel receiver gauge reading by 15.0 liters (15.9 US qts, 13.2 Imp. qts) or more for approximately 2 minutes, output values from both gauge assemblies are immediately reflected in the fuel receiver gauge reading to compensate for a situation when refueling judgment cannot be made.


WIRING DIAGRAM

E316680E04
5,2.969 6.885,3.354 1.885,0.385 10 false G9 5,3.125 6.885,3.51 1.885,0.385 10 false Combination Meter Assembly 0.417,2.969 2.906,3.406 2.49,0.438 10 false O6 0.427,3.156 3.865,3.448 3.438,0.292 10 false Fuel Suction with Pump and Gauge Tube Assembly*1 0.615,2.25 3.104,2.688 2.49,0.438 10 false Fuel Sender Gauge Assembly 3.25,0.958 3.875,1.375 0.625,0.417 10 false FV 4.979,0.979 5.604,1.396 0.625,0.417 10 false FV 3.594,0.927 4.219,1.344 0.625,0.417 10 false 1 4.677,0.958 5.302,1.375 0.625,0.417 10 false 24 4.698,1.365 5.323,1.781 0.625,0.417 10 false 25 4.667,1.781 5.292,2.198 0.625,0.417 10 false 26 4.969,1.813 5.594,2.229 0.625,0.417 10 false FE&B 4.979,1.385 5.604,1.802 0.625,0.417 10 false FR 3.25,1.365 3.875,1.781 0.625,0.417 10 false FR 3.25,1.771 3.875,2.188 0.625,0.417 10 false FE 3.594,1.354 4.219,1.771 0.625,0.417 10 false 3 3.594,1.771 4.219,2.188 0.625,0.417 10 false 2 2.469,1.385 3.094,1.802 0.625,0.417 10 false 1 2.469,0.969 3.094,1.385 0.625,0.417 11 false 3 2.5,1.802 3.125,2.219 0.625,0.417 10 false 2 5.688,0.844 6.313,1.26 0.625,0.417 10 false 5 V 6.177,1.615 6.802,2.031 0.625,0.417 10 false CPU 0.406,3.5 3.844,3.792 3.438,0.292 10 false Fuel Tank Vent Tube Assembly*2 0.302,4.104 3.74,4.396 3.438,0.292 10 false *1: for Gasoline Engine 0.313,4.427 3.75,4.719 3.438,0.292 10 false *2: for Diesel Engine

CAUTION / NOTICE / HINT

CAUTION:

Be careful of flames.


NOTICE:

When replacing the combination meter assembly, make sure to replace it with a new one.


PROCEDURE

1.CHECK SYMPTOMS
a.

Ask the customer about the problem symptoms.


Result:
Result Proceed to
Malfunction occurs when adding fuel (Even after adding fuel, reading does not increase at all or increases very slowly, etc.) A
Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom recurs) B
Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom does not recur) (for Diesel Engine) C
Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom does not recur) (for Gasoline Engine) D



A

2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)

B

15.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)

C

22.CHECK FOR DTC (ECD SYSTEM)

D

25.CHECK FOR DTC (SFI SYSTEM)
2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Using the GTS, perform the Active Test.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full or Sender F -
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Meter Operation
50004 122 3
OK:

Fuel receiver gauge indication is normal.



Result:
Result Proceed to
OK (for Diesel Engine) A
OK (for Gasoline Engine) B
NG C



A

3.CHECK FOR DTC (ECD SYSTEM)

B

12.CHECK FOR DTC (SFI SYSTEM)

C

REPLACE COMBINATION METER ASSEMBLY

3.CHECK FOR DTC (ECD SYSTEM)

Result:
Result Proceed to
OK (w/ VSC) A
OK (w/o VSC, w/ ABS) B
OK (w/o ABS) C
NG D



A

4.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)

B

13.CHECK FOR DTC (ANTI-LOCK BRAKE SYSTEM)

C

5.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL

D

4.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

5.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL

NG

5.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL
a.

Record the fuel receiver gauge reading.


b.

If the fuel tank sub-assembly is almost full, drain 20 liters or more of fuel. (This is not necessary when the fuel tank sub-assembly is sufficiently below full.)


c.

Disconnect the cable from the negative (-) battery terminal to reset the fuel receiver gauge.

HINT:

Check that the ignition switch is turned off before disconnecting the cable from the negative (-) battery terminal.



d.

Connect the cable to the negative (-) battery terminal and turn the ignition switch to ON.


e.

Check that the fuel receiver gauge has been reset.


f.

Drive the vehicle at 1.75 km/h (1.09 mph) or more, then move the shift lever to P and turn the ignition switch off.


g.

Add 5.0 liters or more of fuel, turn the ignition switch to ON, and check that the fuel receiver gauge reading increases in proportion to the amount of fuel added.


Result:
Result Proceed to
Fuel receiver gauge reading increases in proportion to the amount of fuel added A
Fuel receiver gauge reading does not change even when fuel is added B



A

6.INSPECT FUEL TANK SUB-ASSEMBLY

B

7.READ VALUE USING GTS (FUEL INPUT)
6.INSPECT FUEL TANK SUB-ASSEMBLY
HINT:

Inspect the fuel tank sub-assembly for deformation, foreign matter or an improperly installed fuel receiver gauge, as this may be the cause of a fuel receiver gauge malfunction.


a.

Visually check the fuel tank sub-assembly for any abnormalities.


b.

Check if there is an excessive amount of foreign matter in the fuel tank sub-assembly.


c.

Check the installation condition of the fuel tank sub-assembly and fuel sender gauge assembly.


Result:
Result Proceed to
Normal A
Appearance of the fuel tank sub-assembly is abnormal. (for Diesel Engine) B
Appearance of the fuel tank sub-assembly is abnormal. (for Gasoline Engine) C
There is an excessive amount of foreign matter in the fuel tank sub-assembly. D
The fuel tank sub-assembly or fuel sender gauge assembly is not installed correctly. E



A

7.READ VALUE USING GTS (FUEL INPUT)

B

C

D

CLEAN INSIDE OF FUEL TANK SUB-ASSEMBLY

E

INSTALL FUEL TANK SUB-ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY CORRECTLY

7.READ VALUE USING GTS (FUEL INPUT)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input Min.: 0, Max.: 127.5 Current fuel level displayed Unit: Liter
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39
OK:

Fuel level data displayed on the GTS is almost the same as the fuel receiver gauge indication.



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)

NG

REPLACE COMBINATION METER ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)
a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the O6 fuel suction tube with pump and gauge assembly*1 or fuel tank vent tube assembly*2 connector.

*1: for Gasoline Engine

*2: for Diesel Engine



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-25 (FR) - O6-3 (FR) Always Below 1 Ω
G9-24 (FV) - O6-1 (FV) Always Below 1 Ω
G9-26 (FE&B) - O6-2 (FE) Always Below 1 Ω
G9-25 (FR) or O6-3 (FR) - Body ground Always 10 kΩ or higher
G9-24 (FV) or O6-1 (FV) - Body ground Always 10 kΩ or higher
G9-26 (FE&B) or O6-2 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK COMBINATION METER ASSEMBLY
a.
E317793C03
1.49,0.188 1.958,0.417 0.469,0.229 2.906,1.667 2.729,1.667 2.729,1.667 2.281,1.302 true 2.51,1.99 2.333,1.99 2.333,1.99 2.104,1.292 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.625,0.208 1.938,0.365 0.313,0.156 10 false G9 2.979,1.552 3.292,1.708 0.313,0.156 10 false FV 2.552,1.875 3.052,2.052 0.5,0.177 10 false FE&B
*a Component with harness connected
(Combination Meter Assembly)


Remove the combination meter assembly with its connectors still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G9-24 (FV) - Body ground Always 4.5 to 5.2 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-26 (FE&B) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

10.INSPECT FUEL SENDER GAUGE ASSEMBLY


Result:
Result Proceed to
OK (for Gasoline Engine) A
OK (for Diesel Engine) B
NG C



A

11.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

B

14.INSPECT FUEL TANK VENT TUBE ASSEMBLY

C

11.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
a.
E322191C01
0.156,0.104 0.469,0.26 0.313,0.156 10 false *a 0.115,1.885 0.427,2.042 0.313,0.156 10 false *b 1.625,0.417 1.938,0.573 0.313,0.156 10 false *c 1.625,1.802 1.938,1.958 0.313,0.156 10 false *d
*a Upper Side
*b Lower Side
(to Fuel Sender Gauge Assembly)
*c Connector A
*d Connector B


Remove the fuel suction with pump and gauge tube assembly.

for 1TR-FE: Click hereEngine / Hybrid System>1TR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL

for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL

for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-2 Always Below 1 Ω
A-3 - B-1 Always Below 1 Ω
A-1 - B-3 Always Below 1 Ω
A-2 - B-1 Always 10 kΩ or higher
A-2 - B-3 Always 10 kΩ or higher
A-3 - B-3 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

12.CHECK FOR DTC (SFI SYSTEM)
a.

Check for DTCs.

for 1TR-FE: Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234
OK:

No DTCs are output.



Result:
Result Proceed to
OK (w/ VSC) A
OK (w/o VSC, w/ ABS) B
OK (w/o ABS) C
NG D



A

4.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)

B

13.CHECK FOR DTC (ANTI-LOCK BRAKE SYSTEM)

C

5.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL

D

13.CHECK FOR DTC (ANTI-LOCK BRAKE SYSTEM)
a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

5.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL

NG

14.INSPECT FUEL TANK VENT TUBE ASSEMBLY
a.
E322191C01
0.156,0.104 0.469,0.26 0.313,0.156 10 false *a 0.115,1.885 0.427,2.042 0.313,0.156 10 false *b 1.625,0.417 1.938,0.573 0.313,0.156 10 false *c 1.625,1.802 1.938,1.958 0.313,0.156 10 false *d
*a Upper Side
*b Lower Side
(to Fuel Sender Gauge Assembly)
*c Connector A
*d Connector B


Remove the fuel tank vent tube assembly.

for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL

for 2GD-FTV: Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL

for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL

for 2KD-FTV: Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL

for 5L-E: Click hereEngine / Hybrid System>5L-E FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-2 Always Below 1 Ω
A-3 - B-1 Always Below 1 Ω
A-1 - B-3 Always Below 1 Ω
A-2 - B-1 Always 10 kΩ or higher
A-2 - B-3 Always 10 kΩ or higher
A-3 - B-3 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

15.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Using the GTS, perform the Active Test.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full or Sender F -
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Meter Operation
50004 122 3
OK:

Fuel receiver gauge indication is normal.



Result:
Result Proceed to
OK (for Diesel Engine) A
OK (for Gasoline Engine) B
NG C



A

16.CHECK FOR DTC (ECD SYSTEM)

B

20.CHECK FOR DTC (SFI SYSTEM)

C

REPLACE COMBINATION METER ASSEMBLY

16.CHECK FOR DTC (ECD SYSTEM)

Result:
Result Proceed to
OK (w/ VSC) A
OK (w/o VSC, w/ ABS) B
OK (w/o ABS) C
NG D



A

17.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)

B

21.CHECK FOR DTC (ANTI-LOCK BRAKE SYSTEM)

C

18.CHECK FOR DTC

D

17.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

18.CHECK FOR DTC

NG

18.CHECK FOR DTC
a.

Check for DTC.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122
OK:

DTC B1500 is not output.



Result:
Proceed to
OK
NG



OK

19.INSPECT FUEL RECEIVER GAUGE

NG

19.INSPECT FUEL RECEIVER GAUGE
a.

Disconnect the cable from the negative (-) battery terminal to reset the fuel receiver gauge.

HINT:

Check that the ignition switch is turned off before disconnecting the cable from the negative (-) battery terminal.



b.

Connect the cable to the negative (-) battery terminal and turn the ignition switch to ON.


c.

Check if the fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank sub-assembly.


Result:
Result Proceed to
Fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank sub-assembly. A
Fuel receiver gauge reading does not correspond with the amount of fuel remaining in the fuel tank sub-assembly. B



A

END

B

7.READ VALUE USING GTS (FUEL INPUT)
20.CHECK FOR DTC (SFI SYSTEM)
a.

Check for DTCs.

for 1TR-FE: Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234
OK:

No DTCs are output.



Result:
Result Proceed to
OK (w/ VSC) A
OK (w/o VSC, w/ ABS) B
OK (w/o ABS) C
NG D



A

17.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)

B

21.CHECK FOR DTC (ANTI-LOCK BRAKE SYSTEM)

C

18.CHECK FOR DTC

D

21.CHECK FOR DTC (ANTI-LOCK BRAKE SYSTEM)
a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

18.CHECK FOR DTC

NG

22.CHECK FOR DTC (ECD SYSTEM)

Result:
Result Proceed to
OK (w/ VSC) A
OK (w/o VSC, w/ ABS) B
OK (w/o ABS) C
NG D



A

23.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)

B

26.CHECK FOR DTC (ANTI-LOCK BRAKE SYSTEM)

C

24.INSPECT FUEL TANK SUB-ASSEMBLY

D

23.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

24.INSPECT FUEL TANK SUB-ASSEMBLY

NG

24.INSPECT FUEL TANK SUB-ASSEMBLY
HINT:

Inspect the fuel tank sub-assembly for deformation, foreign matter or an improperly installed fuel receiver gauge, as this may be the cause of a fuel receiver gauge malfunction.


a.

Visually check the fuel tank sub-assembly for any abnormalities.


b.

Check if there is an excessive amount of foreign matter in the fuel tank sub-assembly.


c.

Check the installation condition of the fuel tank sub-assembly and fuel sender gauge assembly.


Result:
Result Proceed to
Normal A
Appearance of the fuel tank sub-assembly is abnormal. (for Diesel Engine) B
Appearance of the fuel tank sub-assembly is abnormal. (for Gasoline Engine) C
There is an excessive amount of foreign matter in the fuel tank sub-assembly. D
The fuel tank sub-assembly or fuel sender gauge assembly is not installed correctly. E



A

REPLACE COMBINATION METER ASSEMBLY

B

C

D

CLEAN INSIDE OF FUEL TANK SUB-ASSEMBLY

E

INSTALL FUEL TANK SUB-ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY CORRECTLY

25.CHECK FOR DTC (SFI SYSTEM)
a.

Check for DTCs.

for 1TR-FE: Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234
OK:

No DTCs are output.



Result:
Result Proceed to
OK (w/ VSC) A
OK (w/o VSC, w/ ABS) B
OK (w/o ABS) C
NG D



A

23.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)

B

26.CHECK FOR DTC (ANTI-LOCK BRAKE SYSTEM)

C

24.INSPECT FUEL TANK SUB-ASSEMBLY

D

26.CHECK FOR DTC (ANTI-LOCK BRAKE SYSTEM)
a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

24.INSPECT FUEL TANK SUB-ASSEMBLY

NG