The vehicle speed signal consists of pulses sent to the combination meter assembly from the speedometer sensor*1 or brake actuator assembly (skid control ECU)*2.
*1: w/o ABS
*2: w/ ABS
When replacing the combination meter assembly, make sure to replace it with a new one.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.
w/ Entry and Start System:
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system.
w/ Audio and Visual System (for Radio and Display Type):
When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services.
If the body ECU has been replaced, it is necessary to initialize the body ECU.
For vehicles without an entry and start system, go to "Check Body ECU".
*1: for 1GR-FE
*2: for 1TR-FE, 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV, 2KD-FTV
*5: w/ Body ECU
*6: for KD Series Engine, Automatic Transmission
*7: w/ Navigation System
*8: w/ Audio and Visual System (for Radio and Display Type)
*9: w/ Audio and Visual System (for Radio Receiver Type)
*10: for 5L-E
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*10 ECM connector.
Disconnect the G27 body ECU connector.*5
Disconnect the G90 TCM connector.*6
Disconnect the G113 navigation receiver assembly connector.*7
Disconnect the G37 radio and display receiver assembly connector.*8
Disconnect the G117 radio receiver assembly connector.*9
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicles without a body ECU, go to "Check TCM".
*1: for 1GR-FE
*2: for 1TR-FE, 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV, 2KD-FTV
*5: w/ Entry and Start System
*6: for KD Series Engine, Automatic Transmission
*7: w/ Navigation System
*8: w/ Audio and Visual System (for Radio and Display Type)
*9: w/ Audio and Visual System (for Radio Receiver Type)
*10: for 5L-E
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*10 ECM connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G90 TCM connector.*6
Disconnect the G113 navigation receiver assembly connector.*7
Disconnect the G37 radio and display receiver assembly connector.*8
Disconnect the G117 radio receiver assembly connector.*9
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicles without a KD series engine, automatic transmission, go to "Check Navigation Receiver Assembly".
*1: w/ Entry and Start System
*2: w/ Body ECU
*3: w/ Navigation System
*4: w/ Audio and Visual System (for Radio and Display Type)
*5: w/ Audio and Visual System (for Radio Receiver Type)
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the G83 ECM connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*1
Disconnect the G27 body ECU connector.*2
Disconnect the G113 navigation receiver assembly connector.*3
Disconnect the G37 radio and display receiver assembly connector.*4
Disconnect the G117 radio receiver assembly connector.*5
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicles without a navigation system, go to "Check Radio and Display Receiver Assembly".
*1: for 1GR-FE
*2: for 1TR-FE, 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV, 2KD-FTV
*5: w/ Entry and Start System
*6: w/ Body ECU
*7: for KD Series Engine, Automatic Transmission
*8: for 5L-E
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*8 ECM connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G27 body ECU connector.*6
Disconnect the G90 TCM connector.*7
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicles without an audio and visual system (for radio and display type), go to "Check Radio Receiver Assembly".
*1: for 1GR-FE
*2: for 1TR-FE, 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV, 2KD-FTV
*5: w/ Entry and Start System
*6: w/ Body ECU
*7: for KD Series Engine, Automatic Transmission
*8: for 5L-E
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the G88*1, G45*2, G85*3 G83*4 or G120*8 ECM connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G27 body ECU connector.*6
Disconnect the G90 TCM connector.*7
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicles without an audio and visual system (for radio receiver type), go to "Check ECM".
*1: for 1GR-FE
*2: for 1TR-FE, 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV, 2KD-FTV
*5: w/ Entry and Start System
*6: w/ Body ECU
*7: for KD Series Engine, Automatic Transmission
*8: for 5L-E
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*8 ECM connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G27 body ECU connector.*6
Disconnect the G90 TCM connector.*7
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: w/ Entry and Start System
*2: w/ Body ECU
*3: for KD Series Engine, Automatic Transmission
*4: w/ Navigation System
*5: w/ Audio and Visual System (for Radio and Display Type)
*6: w/ Audio and Visual System (for Radio Receiver Type)
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*1
Disconnect the G27 body ECU connector.*2
Disconnect the G90 TCM connector.*3
Disconnect the G113 navigation receiver assembly connector.*4
Disconnect the G37 radio and display receiver assembly connector.*5
Disconnect the G117 radio receiver assembly connector.*6
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ ABS | A |
| w/o ABS | B |
A
B
| *A | w/ VSC |
| *B | w/o VSC |
| *a | Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU]) |
Disconnect the brake actuator assembly (skid control ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A4-14 (SP1) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A3-22 (SP1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Combination Meter Assembly) |
| *b | Waveform |
Remove the combination meter assembly with the connector(s) still connected.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Connect an oscilloscope to terminal G9-18 (SI) and body ground.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Tester Connection | G9-18 (SI) - Body ground |
| Tool Setting | 5 V/DIV, 20 ms./DIV |
| Vehicle Condition | Driving at approximately 20 km/h (12 mph) |
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.
The waveform displayed is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/ VSC: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/ VSC)>REMOVAL
w/o VSC: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/o VSC)>REMOVAL
*1: for 1GR-FE
*2: for 1TR-FE, 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV, 2KD-FTV
*5: w/ Body ECU
*6: for KD Series Engine, Automatic Transmission
*7: w/ Navigation System
*8: w/ Audio and Visual System (for Radio and Display Type)
*9: w/ Audio and Visual System (for Radio Receiver Type)
*10: for 5L-E
Disconnect the G9 combination meter assembly connector.
Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*10 ECM connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.
Disconnect the G27 body ECU connector.*5
Disconnect the G90 TCM connector.*6
Disconnect the G113 navigation receiver assembly connector.*7
Disconnect the G37 radio and display receiver assembly connector.*8
Disconnect the G117 radio receiver assembly connector.*9
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G69-7 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G69-7 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 1GR-FE
*2: for 1TR-FE, 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV, 2KD-FTV
*5: w/ Entry and Start System
*6: for KD Series Engine, Automatic Transmission
*7: w/ Navigation System
*8: w/ Audio and Visual System (for Radio and Display Type)
*9: w/ Audio and Visual System (for Radio Receiver Type)
*10: for 5L-E
Disconnect the G9 combination meter assembly connector.
Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*10 ECM connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G27 body ECU connector.
Disconnect the G90 TCM connector.*6
Disconnect the G113 navigation receiver assembly connector.*7
Disconnect the G37 radio and display receiver assembly connector.*8
Disconnect the G117 radio receiver assembly connector.*9
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G27-5 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G27-5 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG
*1: w/ Entry and Start System
*2: w/ Body ECU
*3: w/ Navigation System
*4: w/ Audio and Visual System (for Radio and Display Type)
*5: w/ Audio and Visual System (for Radio Receiver Type)
Disconnect the G9 combination meter assembly connector.
Disconnect the G83 ECM connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*1
Disconnect the G27 body ECU connector.*2
Disconnect the G90 TCM connector.
Disconnect the G113 navigation receiver assembly connector.*3
Disconnect the G37 radio and display receiver assembly connector.*4
Disconnect the G117 radio receiver assembly connector.*5
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G90-25 (SPD1) | Always | Below 1 Ω |
| G9-19 (+S) or G90-25 (SPD1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 1GR-FE
*2: for 1TR-FE, 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV, 2KD-FTV
*5: w/ Entry and Start System
*6: w/ Body ECU
*7: for KD Series Engine, Automatic Transmission
*8: for 5L-E
Disconnect the G9 combination meter assembly connector.
Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*8 ECM connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G27 body ECU connector.*6
Disconnect the G90 TCM connector.*7
Disconnect the G113 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G113-17 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G113-17 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 1GR-FE
*2: for 1TR-FE, 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV, 2KD-FTV
*5: w/ Entry and Start System
*6: w/ Body ECU
*7: for KD Series Engine, Automatic Transmission
*8: for 5L-E
Disconnect the G9 combination meter assembly connector.
Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*8 ECM connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G27 body ECU connector.*6
Disconnect the G90 TCM connector.*7
Disconnect the G37 radio receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G37-17 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G37-17 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 1GR-FE
*2: for 1TR-FE, 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV, 2KD-FTV
*5: w/ Entry and Start System
*6: w/ Body ECU
*7: for KD Series Engine, Automatic Transmission
*8: for 5L-E
Disconnect the G9 combination meter assembly connector.
Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*8 ECM connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G27 body ECU connector.*6
Disconnect the G90 TCM connector.*7
Disconnect the G117 radio receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G117-17 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G117-17 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 1GR-FE
*2: for 1TR-FE, 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV, 2KD-FTV
*5: w/ Entry and Start System
*6: w/ Body ECU
*7: for KD Series Engine, Automatic Transmission
*8: w/ Navigation System
*9: w/ Audio and Visual System (for Radio and Display Type)
*10: w/ Audio and Visual System (for Radio Receiver Type)
*11: for 5L-E
Disconnect the G9 combination meter assembly connector.
Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*11 ECM connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G27 body ECU connector.*6
Disconnect the G90 TCM connector.*7
Disconnect the G113 navigation receiver assembly connector.*8
Disconnect the G37 radio and display receiver assembly connector.*9
Disconnect the G117 radio receiver assembly connector.*10
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G88-12 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G88-12 (SPD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G45-23 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G45-23 (SPD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G85-10 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G85-10 (SPD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G83-17 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G83-17 (SPD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G120-25 (SP1) | Always | Below 1 Ω |
| G9-19 (+S) or G120-25 (SP1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>ECM>REMOVAL
for 1TR-FE: Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>ECM>REMOVAL
for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ECM>REMOVAL
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2GD-FTV: Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>REMOVAL
for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2KD-FTV: Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL
for 5L-E: Click hereEngine / Hybrid System>5L-E ENGINE CONTROL>ECM>REMOVAL
NG
| *a | Component with harness connected
(Combination Meter Assembly) |
| *b | Waveform |
Remove the combination meter assembly with the connector(s) still connected.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Connect an oscilloscope to terminal G9-18 (SI) and body ground.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Tester Connection | G9-18 (SI) - Body ground |
| Tool Setting | 5 V/DIV, 20 ms./DIV |
| Vehicle Condition | Driving at approximately 20 km/h (12 mph) |
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.
The waveform displayed is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G9 combination meter assembly connector.
Disconnect the A4*1 or A3*2 brake actuator assembly (skid control ECU) connector.
*1: w/ VSC
*2: w/o VSC
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-18 (SI) - A4-14 (SP1) | Always | Below 1 Ω |
| G9-18 (SI) or A4-14 (SP1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-18 (SI) - A3-22 (SP1) | Always | Below 1 Ω |
| G9-18 (SI) or A3-22 (SP1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C62 speedometer sensor connector.
Disconnect the G9 and G10 combination meter assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C62-3 (SI) - G9-18 (SI) | Always | Below 1 Ω |
| C62-3 (SI) or G9-9 (SI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG