Home › Engine / Hybrid System › 5L-E ENGINE MECHANICAL › CYLINDER HEAD GASKET › from 2016.01
RM3250E _51 Engine / Hybrid System _049911 5L-E ENGINE MECHANICAL _0245945 CYLINDER HEAD GASKET A

5L-E ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of timing belt Mode reset operation
·

Does not illuminate when replacement is necessary

·

Illuminates when replacement is not necessary


(Click here)

CAUTION:
A343695

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


PROCEDURE

Hide 87245A 4.DISCONNECT HEATER WATER HOSE SUB-ASSEMBLY

Hide 23701 5.REMOVE INJECTION PIPE SUB-ASSEMBLY

Hide 6.DISCONNECT WIRE HARNESS

a.
A378617C01
1.802,1.74 2.198,1.74 false 1.833,2.042 2.198,2.042 false 1.844,2.26 2.177,2.26 false 1.875,2.677 2.198,2.677 false 2.24,1.646 2.552,1.802 0.313,0.156 10 false *1 2.25,1.948 2.563,2.104 0.313,0.156 10 false *2 2.25,2.167 2.563,2.323 0.313,0.156 10 false *3 2.25,2.583 2.563,2.74 0.313,0.156 10 false *4
*1 Nut
*2 Plate Washer
*3 No. 2 Glow Plug Resistor Insulator
*4 Wire Harness


Remove the nut, plate washer and No. 2 glow plug resistor insulator and disconnect the wire harness.


b.
A376793

Disconnect the engine coolant temperature sensor connector.


c.

Detach the 7 wire harness clamps and disconnect the wire harness.


Hide 23770B 7.DISCONNECT FUEL HOSE

a.
A376794

Slide the clamp and disconnect the fuel hose from the nozzle leakage pipe assembly.


Hide 11101 8.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A057446N01
0.365,0.271 0.542,0.531 0.177,0.26 10 false 2 2.802,1.875 2.979,2.135 0.177,0.26 10 false 7 2.438,1.698 2.615,1.958 0.177,0.26 10 false 9 0.688,0.125 0.865,0.385 0.177,0.26 10 false 8 3.104,1.688 3.281,1.948 0.177,0.26 10 false 1 0.75,1.896 0.927,2.156 0.177,0.26 10 false 6 2.74,0.115 2.917,0.375 0.177,0.26 10 false 5 0.375,1.719 0.552,1.979 0.177,0.26 10 false 4 3.083,0.26 3.26,0.521 0.177,0.26 10 false 3 0.99,0.26 1.25,0.51 0.26,0.25 10 false 10 1.031,1.708 1.292,1.958 0.26,0.25 10 false 12 2.354,0.25 2.615,0.5 0.26,0.25 10 false 11 1.385,1.896 1.646,2.146 0.26,0.25 10 false 14 1.677,0.26 1.938,0.51 0.26,0.25 10 false 18 2.073,1.885 2.333,2.135 0.26,0.25 10 false 15 1.323,0.115 1.583,0.365 0.26,0.25 10 false 16 2.01,0.094 2.271,0.344 0.26,0.25 10 false 13 1.698,1.708 1.958,1.958 0.26,0.25 10 false 17

Uniformly loosen and remove the 18 cylinder head set bolts in several steps in the sequence shown.

NOTICE:

Cylinder head warpage or cracking could result from removing bolts in the incorrect order.



b.

Lift the cylinder head sub-assembly from the dowels on the cylinder block sub-assembly, and place the cylinder head sub-assembly on wooden blocks on a bench.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and cylinder block sub-assembly.


HINT:

If the cylinder head sub-assembly is difficult to lift, use a screwdriver to pry between the cylinder head sub-assembly and cylinder block sub-assembly.



Hide 11101A 9.INSPECT CYLINDER HEAD SET BOLT

Hide 11115 10.REMOVE CYLINDER HEAD GASKET