Home › Engine / Hybrid System › 5L-E ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2016.01
RM3250E _51 Engine / Hybrid System _049911 5L-E ENGINE MECHANICAL _0245948 ENGINE ASSEMBLY A

5L-E ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of timing belt Mode reset operation
·

Does not illuminate when replacement is necessary

·

Illuminates when replacement is not necessary


(Click here)

CAUTION:
A343695

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 51410 3.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442 4.REMOVE NO. 2 ENGINE UNDER COVER

Hide 8.DRAIN POWER STEERING FLUID

Hide 53301 9.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer nozzle hose from the hood sub-assembly.


b.

Remove the 4 bolts and hood sub-assembly from the 2 hood hinge assemblies.


Hide 44310A 10.REMOVE VANE PUMP V BELT

Hide 88320 11.REMOVE COOLER COMPRESSOR V BELT (w/ Air Conditioning System)

Hide 16361A 12.REMOVE FAN AND GENERATOR V BELT

Hide 16400 13.REMOVE RADIATOR ASSEMBLY

Hide 55550 14.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 82121 15.DISCONNECT ENGINE WIRE


b.
A376802

Detach the 2 clamps and disconnect the 3 connectors from the instrument panel wire.


c.
A376803

Disconnect the 2 wire harness clamps.


d.

Detach the grommet and pull out the engine wire from the cabin.


Hide 17705 16.REMOVE AIR CLEANER CAP AND HOSE

a.
A376804

Detach the 5 wire harness clamps and disconnect the connector from the intake air temperature sensor.


b.
A376805

Loosen the hose clamp.


c.

Detach the 4 clips and remove the air cleaner cap and hose.


Hide 17801 17.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17700 18.REMOVE AIR CLEANER CASE ASSEMBLY

a.
A344950

Remove the 3 bolts and air cleaner case assembly.


Hide 20.DISCONNECT WIRE HARNESS

a.
A352196

Detach the 3 clips and remove the No. 1 relay block upper cover from the engine room relay block sub-assembly.


b.
A352197

Detach the 2 clips and remove the No. 1 relay block side cover from the engine room relay block sub-assembly.


c.
A352198

Remove the nut and disconnect the wire to wire from the engine room relay block sub-assembly.


d.
A352199

Disconnect the 2 connectors from the engine room relay block sub-assembly.


e.
A352200

Detach the clamp, remove the 2 bolts and disconnect the No. 2 engine wire.


f.
A352201

Remove the nut and disconnect the engine room main wire from the battery positive cable.


Hide 74451B 21.REMOVE BATTERY HOLD DOWN CLAMP

a.

Loosen the 2 nuts and remove the battery clamp sub-assembly from the body.


Hide 28800 22.REMOVE BATTERY

Hide 74431 23.REMOVE BATTERY TRAY

Hide 87245A 24.DISCONNECT HEATER WATER HOSE ASSEMBLY

a.
A376807

Remove the bolt, slide the 2 clamps and disconnect the heater water hose assembly from the engine assembly.


Hide 23770B 25.DISCONNECT FUEL HOSE

a.
A121131

Slide the 2 clamps and disconnect the 2 fuel hoses from the injection pump assembly.


Hide 88320 26.DISCONNECT COMPRESSOR ASSEMBLY WITH MAGNET CLUTCH (w/ Air Conditioning System)

a.
A376806

Disconnect the connector.


b.

Remove the 4 bolts and disconnect the compressor assembly with magnet clutch.

HINT:

It is not necessary to completely remove the compressor assembly with magnet clutch. With the hoses connected to the compressor assembly with magnet clutch, hang the compressor assembly with magnet clutch on the vehicle body with a rope.



Hide 44320 27.DISCONNECT VANE PUMP ASSEMBLY

a.
A071326E03
0.344,0.979 0.49,0.979 0.49,0.979 1.177,1.188 true 0.031,0.885 0.365,1.052 0.333,0.167 10 false SST

Using SST, hold the vane pump pulley and loosen the nut.

SST
09960-10010  (09962-01000, 09963-01000)


b.

Remove the nut and vane pump pulley from the vane pump shaft.


c.

Remove the 2 bolts and nut and disconnect the vane pump.

HINT:

Disconnect the vane pump from the vehicle with the hoses connected, and hang it with a rope.



Hide 27020 28.REMOVE GENERATOR ASSEMBLY

Hide 17410 29.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 37100 31.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 33030 32.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY

Hide 31210 33.REMOVE CLUTCH COVER ASSEMBLY

Hide 31250 34.REMOVE CLUTCH DISC ASSEMBLY

Hide 13405 35.REMOVE FLYWHEEL SUB-ASSEMBLY

a.
A058716E02
1.042,0.635 0.76,1.458 0.76,1.458 1,0.969 true 0.531,1.49 0.833,1.646 0.302,0.156 10 false SST

Using SST, hold the crankshaft pulley.

SST
09213-54015  (91651-60855)
09330-00021  


b.

Remove the 8 bolts and flywheel sub-assembly from the crankshaft.


Hide 11355 36.REMOVE REAR END PLATE

a.

Remove the 2 bolts and rear end plate from the cylinder block sub-assembly.


Hide 11354 37.REMOVE FLYWHEEL HOUSING DUST SEAL

Hide 38.INSTALL NO. 2 ENGINE HANGER

a.
A058743

Install the No. 2 engine hanger with bolt as shown in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:

Install the engine hangers with new bolts.


HINT:
Part No.
No. 2 Engine Hanger 12282-54050
Bolt 91622-61022



Hide 39.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine assembly with a chain block.


b.
A376808C02
0.25,0.146 0.573,0.354 0.323,0.208 10 true *A 1.896,0.167 2.208,0.323 0.313,0.156 10 false *B
*A for RH Side
*B for LH Side


Remove the 4 nuts and 4 bolts from the body.


c.

Remove the engine assembly by operating the engine sling device and chain block.


Hide 40.INSTALL ENGINE TO ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.



a.

Install the engine assembly to an engine stand with the bolts.


b.

Remove the bolt and No. 2 engine hanger.


Hide 41.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly.


Hide 12361 42.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
A380555

Remove the 2 nuts and 2 front engine mounting insulators from the 2 front engine mounting brackets.