Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR(for Double Cab) › from 2016.03
RM3250E _59 Vehicle Exterior _038077 DOOR / HATCH _0186370 REAR DOOR(for Double Cab) A

DOOR / HATCH  REAR DOOR(for Double Cab)  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear door disassembly/reassembly are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)
·

Power window regulator motor assembly

·

Door window regulator assembly

·

Door glass

·

Door glass run


Initialize power window control system
·

Jam protection function

·

Power window control system

·

Auto up and down function

·

Remote control function

·

Key-off operation function

·

Catch protection function


(Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

Fully open the rear door glass sub-assembly LH before proceeding with work.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67674A 3.REMOVE REAR DOOR FRAME GARNISH LH

a.
B414892

Detach the clip and claw and remove the rear door frame garnish LH.


Hide 74260 4.REMOVE REAR ARMREST ASSEMBLY LH

a.
B414893C01
0,0 0,0 false
V113146

Place Hands Here
V100135

Order of Removal
V113147

Remove in this Direction


Detach the clip and claw and remove the rear armrest assembly LH.


Hide 5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)

a.
B414894C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clip and claw.


b.

Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.


Hide 84810D 6.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (w/ Power Window)

Hide 69260E 7.REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

a.
B404242C01
0,0 0,0 false
V100155

Protective Tape
V113147

Remove in this Direction


Insert a clip remover between the plate and rear door trim board.

HINT:

Tape the clip remover tip before use.



b.

Turn the handle clockwise to remove the snap ring, rear door window regulator handle assembly and plate.


Hide 69284D 8.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH

a.
B414896

Using moulding remover A, detach the claw and remove the rear door inside handle bezel plug LH as shown in the illustration.


Hide 67604 9.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B414897

Remove the 3 screws.


b.
B414898C01
0,0 0,0 false
V113146

Place Hands Here
V100135

Order of Removal (1)
V100136

Order of Removal (2)
V113147

Remove in this Direction


Detach the clip as shown in the illustration.


c.
B414899C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the guide and remove the rear door trim board sub-assembly LH as shown in the illustration.


d.
B412073C02
2.531,0.917 2.531,0.49 2.531,0.49 2.208,0.49 true 2.104,1.823 2.531,1.823 2.531,1.823 2.531,1.385 true 2,0.375 2.219,0.594 0.219,0.219 10 true *1 1.948,1.719 2.167,1.938 0.219,0.219 10 true *2
*1 Rear Door Inside Looking Cable Assembly LH
*2 Rear Door Lock Remote Control Cable Assembly LH
V113147

Remove in this Direction


Detach the clamp and disconnect the rear door lock remote control cable assembly LH and rear door inside looking cable assembly LH as shown in the illustration.


Hide 69206C 10.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B414900C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and guide and remove the rear door inside handle sub-assembly LH.


Hide 68174A 11.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

a.
B414901

Raise the claw of the rear door inner glass weatherstrip LH as shown in the illustration, and then remove the rear door inner glass weatherstrip LH from the rear door trim board sub-assembly LH.


Hide 67842E 13.REMOVE REAR DOOR SERVICE HOLE COVER LH

a.
B414902C01
0,0 0,0 false
V100143

Butyl Tape


Detach the clamp.


b.

Pull out the rear door lock remote control cable assembly LH, rear door inside locking cable assembly LH and wire harness from the rear door service hole cover LH, and then remove the rear door service hole cover LH.

NOTICE:

Remove any remaining butyl tape from the rear door panel.



Hide 14.REMOVE SCREW GROMMET

a.
B414903

Using a clip remover, detach the claw and remove the 2 screw grommets.


Hide 68152C 15.REMOVE REAR DOOR GLASS RUN LH

a.
B414904

Detach the guide and remove the rear door glass run LH.


Hide 67408E 16.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

a.
B414905C01
0,0 0,0 false
V100135

Bolt
V100136

Screw


Lift up the rear door weatherstrip LH and remove the screw.


b.

Remove the 2 bolts and rear door window division bar sub-assembly LH.


Hide 68104 17.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

a.
B414906

Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.


b.
B414907C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the rear door glass sub-assembly LH as indicated by the arrows in the order shown in the illustration.

NOTICE:

Be careful not to damage the rear door glass sub-assembly LH.



Hide 75740 18.REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

Hide 68124C 19.REMOVE REAR DOOR QUARTER WINDOW GLASS LH

a.
B414908C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door quarter window glass LH together with the rear door quarter window weatherstrip LH.


Hide 68189 20.REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH

a.
B414909

Remove the rear door quarter window weatherstrip LH from the rear door quarter window glass LH.


Hide 69804 21.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

w/ Power Window:

Disconnect the connector.


b.

Loosen the temporarily bolt.

NOTICE:

Do not remove the temporarily bolt. If the temporarily bolt is removed, the rear door window regulator sub-assembly LH may fall and become damaged.



c.

w/ Power Window:

Remove the 3 bolts and rear door window regulator sub-assembly LH.


d.

w/o Power Window:

Remove the 2 bolts and rear door window regulator sub-assembly LH.

B414910C02
0.406,0.052 0.719,0.25 0.313,0.198 10 true *A 3.917,0.073 4.229,0.271 0.313,0.198 10 true *B
*A w/o Power Window *B w/ Power Window
V100135

Bolt
V100136

Connector
V100137

Temporarily Bolt - -



e.

Remove the temporarily bolt from the rear door window regulator sub-assembly LH.


Hide 85720C 22.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Power Window)

Hide 67836H 23.REMOVE REAR DOOR LOCK CHILD PROTECTION COVER LH

a.
B414911

Remove the rear door lock child protection cover LH.


Hide 69340 24.REMOVE REAR DOOR LOCK ASSEMBLY LH

Hide 69038A 25.REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)

Hide 69780B 26.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

Hide 69740D 27.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

Hide 69318C 28.REMOVE DOOR LOCK WIRING HARNESS SEAL

Hide 69227M 29.REMOVE REAR DOOR OUTSIDE HANDLE COVER

a.
B414912C01
0,0 0,0 false
V113147

Remove in this Direction


Using a T30 "TORX" socket wrench, loosen the screw.


b.

Detach the claw and remove the rear door outside handle cover as shown in the illustration.


Hide 69240 30.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B414913C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door outside handle assembly LH as shown in the illustration.


Hide 69241G 31.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B414914C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the rear door front outside handle pad.


Hide 69242G 32.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B414915C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the rear door rear outside handle pad.


Hide 69204A 33.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B414916C01
2.385,0.552 2.385,0.208 2.385,0.208 2.51,0.208 true 2.635,1.094 2.375,1.094 2.375,1.094 2.375,0.875 true 1.302,0.667 1.302,0.385 1.302,0.385 1.125,0.385 true 0.938,0.281 1.156,0.51 0.219,0.229 10 true *a 2.51,0.115 2.729,0.344 0.219,0.229 10 true *b 2.552,0.99 2.771,1.219 0.219,0.229 10 true *b
*a Grommet
*b Guide
V113147

Remove in this Direction


Using a T30 "TORX" socket wrench, loosen the screw.


b.

Detach the grommet and guide and remove the rear door outside handle frame sub-assembly LH.


Hide 67003C 34.REMOVE REAR DOOR PANEL CUSHION

a.
B414917

Detach the claw and remove the rear door panel cushion.


Hide 68640A 35.REMOVE REAR DOOR CHECK ASSEMBLY LH

a.
B414918C01
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)


Remove the 2 bolts (A), bolt (B) and rear door check assembly LH.


Hide 67872 36.REMOVE REAR DOOR WEATHERSTRIP LH

a.
B414919

Using a clip remover, detach the clip and remove the rear door weatherstrip LH.


Hide 67837C 37.REMOVE REAR DOOR DUST PROOF SEAL

a.
B414920

Detach the claw and remove the 3 rear door dust proof seals.


Hide 75924C 38.REMOVE NO. 2 BLACK OUT TAPE LH (w/ Black Out Tape)