Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE(for Rear Door) › from 2016.03
RM3250E _59 Vehicle Exterior _038080 EXTERIOR PANELS / TRIM _0184371 BLACK OUT TAPE(for Rear Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Rear Door)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the No. 2 black out tape removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

Fully open the rear door glass sub-assembly LH before proceeding with work.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67674A 3.REMOVE REAR DOOR FRAME GARNISH LH

Hide 74260 4.REMOVE REAR ARMREST ASSEMBLY LH

Hide 5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)

Hide 69260E 6.REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

Hide 69284D 7.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH

Hide 67604 8.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 67842E 9.REMOVE REAR DOOR SERVICE HOLE COVER LH

Hide 68152C 10.REMOVE REAR DOOR GLASS RUN LH

Hide 67408E 11.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Hide 68104 12.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

Hide 75740 13.REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

Hide 67872 14.REMOVE REAR DOOR WEATHERSTRIP LH

a.
B407174

Using a clip remover, detach the clip and remove enough of the upper portion of the rear door weatherstrip LH so that the No. 2 black out tape LH can be removed.


Hide 75924C 15.REMOVE NO. 2 BLACK OUT TAPE LH

HINT:

When removing the No. 2 black out tape LH, heat the rear door panel and No. 2 black out tape LH using a heat light.


Standard:
Item Temperature
Rear Door Panel 40 to 60°C (104 to 140°F)
No. 2 Black Out Tape LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.
B403638

Pull back an edge of the No. 2 black out tape LH and pull it parallel to the rear door panel to remove it.