The headlight leveling ECU assembly controls the headlight cleaner motor and pump assembly.
First check that the front washer operates normally.
Inspect the fuses and relays for circuits related to this system before performing the following inspection procedure.
The headlight cleaner system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the window defogger system after confirming that the communication system is functioning properly.
Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
w/ Automatic Headlight Beam Level Control System:
If the headlight leveling ECU assembly has been replaced, it is necessary to initialize the headlight leveling ECU assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION
Clear the DTCs.
Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DTC CHECK / CLEAR
DTC is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Automatic Headlight Beam Level Control System) | B |
| NG (w/o Automatic Headlight Beam Level Control System) | C |
A
B
C
Read the Data List according to the display on the GTS.
Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Front Window Washer Switch | Washer switch condition | ON/OFF | ON: Windshield wiper switch assembly (windshield washer switch) on
OFF: Windshield wiper switch assembly (windshield washer switch) off |
- |
| Tester Display |
|---|
| Front Window Washer Switch |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the headlight cleaner motor and pump assembly.
Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>REMOVAL
Inspect the headlight cleaner motor and pump assembly.
Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the headlight cleaner control relay.
Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER CONTROL RELAY>REMOVAL
Inspect the headlight cleaner control relay.
Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER CONTROL RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Headlight Cleaner Control Relay) |
Disconnect the headlight cleaner control relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A57-4 (E) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A57-3 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A58 headlight cleaner motor and pump assembly connector.
Disconnect the A57 headlight cleaner control relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-1 - A57-6 (PB) | Always | Below 1 Ω |
| A58-1 or A57-6 (PB) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-2 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G80 headlight leveling ECU assembly connector.
Disconnect the A57 headlight cleaner control relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G80-16 (HLC) - A57-2 (H) | Always | Below 1 Ω |
| G80-16 (HLC) or A57-2 (H) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G80 headlight light leveling ECU assembly connector.
Disconnect the G18 windshield wiper switch assembly connector.
Disconnect the A2 windshield washer motor and pump assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G80-4 (FRWA) - G18-7 (WF) | Always | Below 1 Ω |
| G80-4 (FRWA) or G18-7 (WF) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G80-4 (FRWA) - G18-4 (WF) | Always | Below 1 Ω |
| G80-4 (FRWA) or G18-4 (WF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG