Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2016.03
RM3250E _58 Vehicle Interior _038065 THEFT DETERRENT / KEYLESS ENTRY _0184917 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the body ECU.

WIRING DIAGRAM

B405279E04
0.156,0.219 4.74,0.417 4.583,0.198 10 false from Engine Stop and Start ECU 0.854,0.677 4.781,0.906 3.927,0.229 10 false from IG1 NO. 4 Fuse 0.479,1.24 4.406,1.469 3.927,0.229 10 false from Door Control Battery*1 2.698,0.594 3.135,0.979 0.438,0.385 10 false *4 2.688,0.104 3.125,0.49 0.438,0.385 10 false *3 0.073,1.917 4,2.146 3.927,0.229 10 false *1: w/ Door Control Battery 0.073,2.188 4,2.417 3.927,0.229 10 false *2: w/o Door Control Battery 3.313,2.125 7.156,2.417 3.844,0.292 10 false Instrument Panel Junction Block Assembly 6.031,2.344 7.156,2.729 1.125,0.385 10 false Body ECU 6.031,1.792 7.156,2.208 1.125,0.417 10 false GND 6.021,1.26 7.146,1.677 1.125,0.417 10 false BECU 6.031,0.698 7.156,1.115 1.125,0.417 10 false IG 5.76,0.677 6.885,1.094 1.125,0.417 10 false A 5.781,1.25 6.906,1.667 1.125,0.417 10 false A 5.802,1.76 6.927,2.177 1.125,0.417 10 false A 5.771,0.521 6.896,0.938 1.125,0.417 10 false 7 5.781,1.052 6.906,1.469 1.125,0.417 10 false 6 5.792,1.573 6.917,1.99 1.125,0.417 10 false 1 3.552,1.26 4.677,1.677 1.125,0.417 10 false 2J 3.563,1.76 4.688,2.177 1.125,0.417 10 false 2J 3.563,0.698 4.688,1.115 1.125,0.417 10 false 2D 3.594,0.51 4.719,0.927 1.125,0.417 10 false 5 3.583,1.063 4.708,1.479 1.125,0.417 10 false 3 3.594,1.583 4.719,2 1.125,0.417 10 false 5 0.563,1.51 4.49,1.74 3.927,0.229 10 false from ECU-B NO. 4 Fuse*2 2.177,2.448 6.104,2.677 3.927,0.229 10 false *4: w/o Stop and Start System 0.083,2.448 4.01,2.677 3.927,0.229 10 false *3: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
B405280C01
1.469,0.292 1.938,0.573 0.469,0.281 1.49,2.604 1.958,2.885 0.469,0.281 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 1.615,0.344 1.927,0.542 0.313,0.198 10 false 2D 1.635,2.667 1.948,2.865 0.313,0.198 10 false 2J
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the instrument panel junction block assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2J-5 - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2D-5 - Body ground Ignition switch ON 11 to 14 V
2J-3 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

b.

Measure the resistance according to the value(s) in the table below.

B405281C01
1.667,0.521 2.052,0.76 0.385,0.24 4.531,0.406 4.896,0.625 0.365,0.219 5.948,0.406 6.313,0.625 0.365,0.219 2.073,1.375 2.292,1.104 true 2.469,1.385 2.417,1.104 true 3.135,1.396 3.083,1.115 true 0.156,0.042 0.469,0.24 0.313,0.198 10 false *a 1.99,1.406 2.302,1.604 0.313,0.198 10 false IG 2.365,1.417 3.188,1.688 0.823,0.271 10 false BECU 2.979,1.406 3.531,1.729 0.552,0.323 10 false GND 1.813,0.573 2.365,0.896 0.552,0.323 10 false A 4.635,0.438 5.188,0.76 0.552,0.323 10 false 2D 6.063,0.438 6.615,0.76 0.552,0.323 10 false 2J
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
2J-5 - A-1 (GND) Always Below 1 Ω
2D-5 - A-7 (IG) Always Below 1 Ω
2J-3 - A-6 (BECU) Always Below 1 Ω



Result:
Proceed to
OK
NG (for LHD)
NG (for RHD)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG (for LHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG (for RHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY