While the engine is being cranked, the ECM detects the starter signal (STA signal) and performs engine control when the engine starts.
If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0617 | Starter Relay Circuit High | Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.5 mph). (b) Engine speed is more than 1000 rpm. (c) STA signal is on. |
·
ST NO. 1 relay circuit*1 ·
ST NO. 2 relay circuit*2 ·
Ignition switch assembly ·
Park/Neutral position switch assembly ·
Clutch start switch assembly ·
Engine stop and start ECU ·
ECM |
Comes on | DTC stored |
*1: w/o Entry and Start System
*2: w/ Entry and Start System
| DTC No. | Data List |
|---|---|
| P0617 | Starter Signal |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0617 | Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>INITIALIZATION).
Read Starter Count before replacing the engine stop and start ECU, perform the replacement procedure, and then write Starter Count to the newly installed engine stop and start ECU.
When replacing the engine stop and start ECU or the air conditioning amplifier assembly, initialize and learn the engine stop and start ECU air conditioning information.
When replacing the engine stop and start ECU or airbag ECU assembly (G sensor), initialize and learn the engine stop and start ECU G sensor zero point learned information.
The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>PROBLEM SYMPTOMS TABLE).
If this DTC is output, inspect the starter assembly.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Read the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more.
| Result | Proceed to | |||
|---|---|---|---|---|
| Driving at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more | OFF | A | ||
| ON | w/ Stop and Start System | B | ||
| w/o Stop and Start System | C | |||
A
B
C
Start the engine.
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Engine Stop and Start ECU) |
- | - |
| Tester Connection | Condition | Specified Condition |
| G126-23 (STA2) - Body ground | Vehicle driving (Engine speed of 1000 rpm or more and vehicle speed at 20 km/h (12.4 mph) or more) | 0 to 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the harness or connector (STA signal circuit).
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0617 is output | A |
| DTCs are not output | B |
A
B
Inspect the clutch start switch.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly.
Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the harness or connector (STA signal circuit).
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ignition switch assembly.
Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON.
Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the clutch start switch assembly.
| Proceed to |
|---|
| NEXT |
NEXT