Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ Urea SCR System) › from 2016.03
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0262511 ECD SYSTEM(w/ Urea SCR System) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P202B  Reductant Tank Heater Control Circuit Low  P202C  Reductant Tank Heater Control Circuit High  


DESCRIPTION

An electric heater is provided inside the urea tank and urea pipe, as urea solution freezes at -11°C (12.2°F) or lower.

The heater thaws frozen urea solution and prevents further freezing, allowing the urea SCR system to be started even in cold environments.

The tank heater turns ON and OFF according to the value of the temperature sensor. The heater for the urea tube with heater assembly turns ON and OFF according to the value of the ambient temperature sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P202B Reductant Tank Heater Control Circuit Low When the tank heater is operating, an open or short circuit occurs in the tank heater for 3 seconds or more (1 trip detection logic).
·

Open or short in tank heater circuit

·

Tank heater (urea pump)

·

Urea pump control ECU


Comes on DTC stored
P202C Reductant Tank Heater Control Circuit High When the tank heater is operating, an open or short circuit occurs in the tank heater for 3 seconds or more (1 trip detection logic).
·

Open or short in tank heater circuit

·

Tank heater (urea pump)

·

Urea pump control ECU


Comes on DTC stored

Related Data List
DTC No. Data List
P202B
P202C
Reductant Tank Heater

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P202B
P202C
Reductant Tank Heater (Active Test)

WIRING DIAGRAM

A357971E05
1.844,1.344 2.302,1.542 0.458,0.198 10 false TH+ 1.875,1.917 2.188,2.115 0.313,0.198 10 false TH- 0.49,2.646 0.802,2.844 0.313,0.198 10 false g6 0.49,2.823 4.01,3.021 3.521,0.198 10 false Tank Heater (Urea Pump) 2.198,1.563 2.354,1.76 0.156,0.198 10 false 9 2.188,2.156 2.5,2.354 0.313,0.198 10 false 11 4.979,1.552 5.292,1.75 0.313,0.198 10 false 21 4.979,2.177 5.292,2.375 0.313,0.198 10 false 31 5.271,1.448 5.729,1.646 0.458,0.198 10 false HTT 5.281,2.063 5.896,2.26 0.615,0.198 10 false EHTT 5.24,2.969 5.552,3.167 0.313,0.198 10 false g1 5.24,3.146 6.896,3.354 1.656,0.208 10 false Urea Pump Control ECU

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT TANK HEATER (UREA PUMP)
a.

Inspect the tank heater (urea pump).

Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>UREA PUMP>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TANK HEATER - UREA PUMP CONTROL ECU)

NG

7.REPLACE UREA PUMP
2.CHECK HARNESS AND CONNECTOR (TANK HEATER - UREA PUMP CONTROL ECU)
A360342C12
1.594,0.125 2.021,0.354 0.427,0.229 5.302,0.115 5.729,0.344 0.427,0.229 1.281,1.385 1.948,0.948 true 2.24,0.958 2.573,1.417 true 4.51,1.458 5.177,1.021 true 5.271,0.823 5.823,1.49 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 4.229,0.156 4.542,0.313 0.313,0.156 10 false *b 1.729,0.167 2.042,0.365 0.313,0.198 10 false g6 5.427,0.156 5.74,0.354 0.313,0.198 10 false g1 1.177,1.406 1.635,1.604 0.458,0.198 10 false TH- 2.542,1.469 3,1.667 0.458,0.198 10 false TH+ 4.042,1.479 5.271,1.677 1.229,0.198 10 false 31(EHTT) 5.656,1.51 6.729,1.708 1.073,0.198 10 false 21(HTT)
*a Front view of wire harness connector
(to Urea Pump)
*b Front view of wire harness connector
(to Urea Pump Control ECU)


a.

Disconnect the urea pump connector.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g6-9 (TH+) - g1-21 (HTT) Always Below 1 Ω
g6-11 (TH-) - g1-31 (EHTT) Always Below 1 Ω
g6-9 (TH+) or g1-21 (HTT) - Body ground and other terminals Always 10 kΩ or higher
g6-11 (TH-) or g1-31 (EHTT) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

6.REPAIR OR REPLACE HARNESS AND CONNECTOR
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Tank Heater.


g.

Perform the Active Test.

Powertrain > Engine > Active Test
Tester Display
Reductant Tank Heater
50004 234 319

h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P202B or P202C is output A
No DTC is output B



A

4.REPLACE UREA PUMP CONTROL ECU

B

END

4.REPLACE UREA PUMP CONTROL ECU

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Tank Heater.


g.

Perform the Active Test.

Powertrain > Engine > Active Test
Tester Display
Reductant Tank Heater
50004 234 319

h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

6.REPAIR OR REPLACE HARNESS AND CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE UREA PUMP

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED