Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ Urea SCR System) › from 2016.03
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0262511 ECD SYSTEM(w/ Urea SCR System) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P204C  Reductant Pressure Sensor Circuit Low  P204D  Reductant Pressure Sensor Circuit High  


DESCRIPTION

Refer to DTC P208B.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>P208B

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P204C Reductant Pressure Sensor Circuit Low An open or short circuit occurs in the pressure sensor circuit for 3 seconds or more (1 trip detection logic).
·

Open or short in pressure sensor circuit

·

Pressure sensor (urea pump)

·

Urea pump control ECU


Comes on DTC stored
P204D Reductant Pressure Sensor Circuit High An open or short circuit occurs in the pressure sensor circuit for 3 seconds or more (1 trip detection logic).
·

Open or short in pressure sensor circuit

·

Pressure sensor (urea pump)

·

Urea pump control ECU


Comes on DTC stored

Related Data List
DTC No. Data List
P204C
P204D
Reductant Pressure

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P204C
P204D
Ignition switch to ON for 3 seconds

WIRING DIAGRAM

A357972E04
1.323,0.438 1.938,0.635 0.615,0.198 10 false VPSE 1.417,1.031 1.875,1.229 0.458,0.198 10 false PSE 1.344,1.573 1.958,1.771 0.615,0.198 10 false EPSE 1.802,0.573 1.958,0.771 0.156,0.198 10 false 5 1.802,1.135 1.958,1.333 0.156,0.198 10 false 4 1.802,1.677 1.958,1.875 0.156,0.198 10 false 3 0.333,2.042 0.646,2.24 0.313,0.198 10 false g6 0.344,2.229 4.469,2.427 4.125,0.198 10 false Pressure Sensor (Urea Pump) 5.688,0.458 6.302,0.656 0.615,0.198 10 false VCPU 5.708,1.031 6.021,1.229 0.313,0.198 10 false PU 5.708,1.583 6.167,1.781 0.458,0.198 10 false EPU 5.385,0.573 5.698,0.771 0.313,0.198 10 false 57 5.396,1.146 5.708,1.344 0.313,0.198 10 false 56 5.396,1.698 5.708,1.896 0.313,0.198 10 false 55 5.417,2.042 5.729,2.24 0.313,0.198 10 false g1 5.417,2.219 6.979,2.427 1.563,0.208 10 false Urea Pump Control ECU

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (REDUCTANT PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Reductant Pressure.


d.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display
Reductant Pressure
50003 234 1132

Result:
Result Proceed to
-50 kPa A
900 kPa B



A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

8.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A360358C04
1.542,0.802 1.885,1.094 0.344,0.292 1.146,2.583 1.635,1.615 true 2.26,2.594 1.792,1.625 true 0.469,0.552 0.781,0.708 0.313,0.156 10 false *a 1.635,0.865 1.948,1.063 0.313,0.198 10 false g6 0.938,2.625 1.552,2.823 0.615,0.198 10 false VPSE 2.125,2.635 2.583,2.833 0.458,0.198 10 false PSE
*a Front view of wire harness connector
(to Urea Pump)


Disconnect the urea pump connector.


b.

Connect terminals 5 (VPSE) and 4 (PSE) of the pressure sensor (urea pump) wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Reductant Pressure.


f.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display
Reductant Pressure
50003 234 1132
OK:

900 kPa



Result:
Proceed to
OK
NG



OK

3.REPLACE UREA PUMP

NG

5.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - UREA PUMP CONTROL ECU)
3.REPLACE UREA PUMP

Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON and wait for 3 seconds or more.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

5.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - UREA PUMP CONTROL ECU)
A360342C14
1.594,0.125 2.021,0.354 0.427,0.229 5.302,0.115 5.729,0.344 0.427,0.229 1.146,1.458 1.729,0.792 true 5.615,1.5 5.646,1.156 true 5.729,1.156 6.417,1.479 true 1.719,1.438 1.854,0.781 true 2.01,0.792 2.406,1.448 true 4.823,1.542 5.583,1.156 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 4.229,0.156 4.542,0.313 0.313,0.156 10 false *b 1.729,0.167 2.042,0.365 0.313,0.198 10 false g6 5.427,0.156 5.74,0.354 0.313,0.198 10 false g1 0.917,1.479 1.375,1.677 0.458,0.198 10 false VPSE 2.344,1.479 2.802,1.677 0.458,0.198 10 false EPSE 4.375,1.552 5.604,1.75 1.229,0.198 10 false 55 (EPU) 6.24,1.51 7.156,1.708 0.917,0.198 10 false 57 (VCPU) 1.635,1.469 2.094,1.667 0.458,0.198 10 false PSE 5.365,1.521 6.438,1.719 1.073,0.198 10 false 56 (PU)
*a Front view of wire harness connector
(to Urea Pump)
*b Front view of wire harness connector
(to Urea Pump Control ECU)


a.

Disconnect the urea pump connector.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g6-5 (VPSE) - g1-57 (VCPU) Always Below 1 Ω
g6-4 (PSE) - g1-56 (PU) Always Below 1 Ω
g6-3 (EPSE) - g1-55 (EPU) Always Below 1 Ω
g6-5 (VPSE) or g1-57 (VCPU) - Body ground and other terminals Always 10 kΩ or higher
g6-4 (PSE) or g1-56 (PU) - Body ground and other terminals Always 10 kΩ or higher
g6-3 (EPSE) or g1-55 (EPU) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE UREA PUMP CONTROL ECU

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE UREA PUMP CONTROL ECU

Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the urea pump connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Reductant Pressure.


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display
Reductant Pressure
50003 234 1132
OK:

-50 kPa



Result:
Proceed to
OK
NG



OK

3.REPLACE UREA PUMP

NG

9.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - UREA PUMP CONTROL ECU)
9.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - UREA PUMP CONTROL ECU)
A360342C14
1.594,0.125 2.021,0.354 0.427,0.229 5.302,0.115 5.729,0.344 0.427,0.229 1.146,1.458 1.729,0.792 true 5.615,1.5 5.646,1.156 true 5.729,1.156 6.417,1.479 true 1.719,1.438 1.854,0.781 true 2.01,0.792 2.406,1.448 true 4.823,1.542 5.583,1.156 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 4.229,0.156 4.542,0.313 0.313,0.156 10 false *b 1.729,0.167 2.042,0.365 0.313,0.198 10 false g6 5.427,0.156 5.74,0.354 0.313,0.198 10 false g1 0.917,1.479 1.375,1.677 0.458,0.198 10 false VPSE 2.344,1.479 2.802,1.677 0.458,0.198 10 false EPSE 4.375,1.552 5.604,1.75 1.229,0.198 10 false 55 (EPU) 6.24,1.51 7.156,1.708 0.917,0.198 10 false 57 (VCPU) 1.635,1.469 2.094,1.667 0.458,0.198 10 false PSE 5.365,1.521 6.438,1.719 1.073,0.198 10 false 56 (PU)
*a Front view of wire harness connector
(to Urea Pump)
*b Front view of wire harness connector
(to Urea Pump Control ECU)


a.

Disconnect the urea pump connector.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g6-5 (VPSE) - g1-57 (VCPU) Always Below 1 Ω
g6-4 (PSE) - g1-56 (PU) Always Below 1 Ω
g6-3 (EPSE) - g1-55 (EPU) Always Below 1 Ω
g6-5 (VPSE) or g1-57 (VCPU) - Body ground and other terminals Always 10 kΩ or higher
g6-4 (PSE) or g1-56 (PU) - Body ground and other terminals Always 10 kΩ or higher
g6-3 (EPSE) or g1-55 (EPU) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE UREA PUMP CONTROL ECU

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR