Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ Urea SCR System) › from 2016.03
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0262511 ECD SYSTEM(w/ Urea SCR System) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P20BB  Reductant Heater "A" Control Circuit Low  P20BC  Reductant Heater "A" Control Circuit High  


DESCRIPTION

Refer to DTC P202B.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>P202B

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P20BB Reductant Heater "A" Control Circuit Low When the urea tube with heater is operating, an open or short circuit occurs in the urea tube with heater circuit for 3 seconds or more (1 trip detection logic).
·

Open or short in urea tube with heater assembly circuit

·

Urea tube with heater assembly

·

Urea pump control ECU


Comes on DTC stored
P20BC Reductant Heater "A" Control Circuit High When the urea tube with heater is operating, an open or short circuit occurs in the urea tube with heater circuit for 3 seconds or more (1 trip detection logic).
·

Open or short in urea tube with heater assembly circuit

·

Urea tube with heater assembly

·

Urea pump control ECU


Comes on DTC stored

Related Data List
DTC No. Data List
P20BB
P20BC
Reductant Pipe Heater

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20BB
P20BC
Reductant Pipe Heater (Active Test)

WIRING DIAGRAM

A357971E06
1.771,1.344 2.302,1.531 0.531,0.188 10 false HTUL 1.792,1.938 2.188,2.135 0.396,0.198 10 false GND 0.49,2.646 0.802,2.844 0.313,0.198 10 false g5 0.49,2.823 2.938,3.24 2.448,0.417 10 false Urea Tube with Heater Assembly 2.198,1.563 2.354,1.76 0.156,0.198 10 false 2 2.208,2.156 2.521,2.354 0.313,0.198 10 false 1 4.979,1.552 5.292,1.75 0.313,0.198 10 false 20 4.979,2.177 5.292,2.375 0.313,0.198 10 false 32 5.271,1.448 5.729,1.646 0.458,0.198 10 false HTL 5.281,2.063 5.896,2.26 0.615,0.198 10 false EHTL 5.24,2.969 5.552,3.167 0.313,0.198 10 false g1 5.24,3.146 6.896,3.438 1.656,0.292 10 false Urea Pump Control ECU

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT UREA TUBE WITH HEATER ASSEMBLY
a.

Disconnect the urea tube with heater assembly connector.


b.
A179479C04
0.135,0.156 0.448,0.313 0.313,0.156 10 false *a
*a Component without harness connected
(to Urea Tube with Heater Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 6.39 to 7.81 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (UREA TUBE WITH HEATER ASSEMBLY - UREA PUMP CONTROL ECU)

NG

7.REPLACE UREA TUBE WITH HEATER ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (UREA TUBE WITH HEATER ASSEMBLY - UREA PUMP CONTROL ECU)
A360346C03
1.583,0.104 1.885,0.354 0.302,0.25 5.323,0.104 5.625,0.354 0.302,0.25 1.271,1.396 1.521,0.969 true 2.229,1.396 1.896,0.979 true 4.75,1.448 5.177,0.781 true 5.552,1.5 5.25,0.979 true 0.667,0.083 0.979,0.24 0.313,0.156 10 false *a 4.219,0.083 4.531,0.24 0.313,0.156 10 false *b 1.656,0.135 1.969,0.333 0.313,0.198 10 false g5 5.385,0.146 5.698,0.344 0.313,0.198 10 false g1 1.031,1.458 1.646,1.656 0.615,0.198 10 false HTUL 2.094,1.448 2.708,1.646 0.615,0.198 10 false GND 4.438,1.479 5.052,1.677 0.615,0.198 10 false 20(HTL) 5.479,1.531 6.094,1.729 0.615,0.198 10 false 32(EHTL)
*a Front view of wire harness connector
(to Urea Tube with Heater Assembly)
*b Front view of wire harness connector
(to Urea Pump Control ECU)


a.

Disconnect the urea tube with heater assembly connector.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g5-2 (HTUL) - g1-20 (HTL) Always Below 1 Ω
g5-1 (GND) - g1-32 (EHTL) Always Below 1 Ω
g5-2 (HTUL) or g1-20 (HTL) - Body ground and other terminals Always 10 kΩ or higher
g5-1 (GND) or g1-32 (EHTL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

6.REPAIR OR REPLACE HARNESS AND CONNECTOR
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Turn the ignition switch off and wait for 30 seconds or more.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Pipe Heater.


g.

Perform the Active Test.

Powertrain > Engine > Active Test
Tester Display
Reductant Pipe Heater
50004 234 318

h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P20BB or P20BC is output A
DTCs is not output B



A

4.REPLACE UREA PUMP CONTROL ECU

B

END

4.REPLACE UREA PUMP CONTROL ECU

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Turn the ignition switch off and wait for 30 seconds or more.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Pipe Heater.


g.

Perform the Active Test.

Powertrain > Engine > Active Test
Tester Display
Reductant Pipe Heater
50004 234 318

h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

6.REPAIR OR REPLACE HARNESS AND CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE UREA TUBE WITH HEATER ASSEMBLY
a.

Replace the urea tube with heater assembly.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED