Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ Urea SCR System) › from 2016.03
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0262511 ECD SYSTEM(w/ Urea SCR System) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  U010E  Lost Communication with Reductant Control Module  


DESCRIPTION

The ECM sends and receives data to and from the urea pump control ECU via local CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U010E Lost Communication with Reductant Control Module Communication stops between the ECM and the urea pump control ECU for 1.6 seconds or more (1 trip detection logic).
·

Urea pump control ECU

·

Harness or connector

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM stores a DTC when a communication malfunction occurs between the ECM and urea pump control ECU.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
U010E 1.6 seconds or more after turning the ignition switch to ON.

WIRING DIAGRAM

A383042E01
0.438,1.125 1.021,1.302 0.583,0.177 10 false J/B-B 0.677,0.51 1.635,0.708 0.958,0.198 10 false AM2 NO. 2 1.979,0.75 2.458,0.948 0.479,0.198 10 false IG1D 2.375,0.854 2.688,1.052 0.313,0.198 10 false 20 1.333,1.083 1.792,1.281 0.458,0.198 10 false G69 1.333,1.25 2.885,1.615 1.552,0.365 10 false Certification ECU (Smart Key ECU Assembly) 4.906,0.521 5.729,0.719 0.823,0.198 10 false IG2 NO. 3 3.625,1.063 4.083,1.26 0.458,0.198 10 false IG2 3.021,2.375 4.677,2.563 1.656,0.188 10 false Ignition Switch Assembly 3.01,2.24 3.323,2.438 0.313,0.198 10 false G1 3.271,1.802 3.729,2 0.458,0.198 10 false AM2 4.021,1.802 4.479,2 0.458,0.198 10 false IG2 4.333,2 4.49,2.198 0.156,0.198 10 false 3 3.115,2 3.271,2.198 0.156,0.198 10 false 4 2.031,7.302 5.698,7.5 3.667,0.198 10 false : CAN Communication Line 0.427,5.302 1.156,5.49 0.729,0.188 10 false FL MAIN 1.49,6.906 3.917,7.115 2.427,0.208 10 false *2: w/o Entry and Start System 1.49,6.552 4.156,6.76 2.667,0.208 10 false *1: w/ Entry and Start System 0.573,6.802 1.281,6.99 0.708,0.188 10 false Battery 3.677,6.135 4.135,6.333 0.458,0.198 10 false G85 3.677,6.302 4.135,6.5 0.458,0.198 10 false ECM 4.74,2.823 5.333,3.021 0.594,0.198 10 false DCU-B 4.771,2.542 4.927,2.74 0.156,0.198 10 false 1 5.031,2.542 5.188,2.74 0.156,0.198 10 false 2 4.635,4.177 5.656,4.354 1.021,0.177 10 false DCU NO. 2 4.625,3.406 5.49,3.594 0.865,0.188 10 false DCU NO. 1 4.771,3.125 4.927,3.323 0.156,0.198 10 false 1 5.031,3.125 5.188,3.323 0.156,0.198 10 false 2 5.031,3.896 5.188,4.094 0.156,0.198 10 false 2 4.771,3.896 4.927,4.094 0.156,0.198 10 false 1 3.323,0.844 3.479,1.042 0.156,0.198 10 false 1 4.042,0.854 4.198,1.052 0.156,0.198 10 false 2 4.042,0.448 4.198,0.646 0.156,0.198 10 false 3 3.333,0.458 3.49,0.656 0.156,0.198 10 false 5 4.99,0.24 5.146,0.438 0.156,0.198 10 false 1 5.25,0.24 5.406,0.438 0.156,0.198 10 false 2 0.854,0.229 1.01,0.427 0.156,0.198 10 false 1 1.094,0.229 1.25,0.427 0.156,0.198 10 false 2 0.177,0.979 0.333,1.177 0.156,0.198 10 false 2 0.177,1.26 0.333,1.458 0.156,0.198 10 false 1 0.854,1.781 1.01,1.979 0.156,0.198 10 false 1 1.104,1.781 1.26,1.979 0.156,0.198 10 false 2 0.833,3.906 0.99,4.104 0.156,0.198 10 false 1 1.094,3.906 1.25,4.104 0.156,0.198 10 false 2 2.26,4.125 2.417,4.323 0.156,0.198 10 false 5 2.969,4.115 3.125,4.313 0.156,0.198 10 false 3 2.26,4.521 2.417,4.719 0.156,0.198 10 false 1 2.969,4.521 3.125,4.719 0.156,0.198 10 false 2 0.479,1.813 0.792,2.01 0.313,0.198 10 false *2 0.146,1.635 0.458,1.833 0.313,0.198 10 false *1 4.219,0.26 4.531,0.458 0.313,0.198 10 false *1 4.563,0.771 4.875,0.969 0.313,0.198 10 false *2 2.833,0.667 3.146,0.865 0.313,0.198 10 false *1 3.823,5.208 4.438,5.406 0.615,0.198 10 false CANU 3.833,5.698 4.448,5.896 0.615,0.198 10 false CAND 5.333,7.302 7.135,7.573 1.802,0.271 11 false Urea Pump Control ECU 5.333,7.073 5.646,7.271 0.313,0.198 10 false g1 6.094,0.375 6.708,0.573 0.615,0.198 10 false IGSW 5.823,0.458 6.135,0.656 0.313,0.198 10 false 18 6.073,2.677 6.688,2.875 0.615,0.198 10 false BATT 6.073,2.979 6.688,3.177 0.615,0.198 10 false +BU5 6.073,3.25 6.688,3.448 0.615,0.198 10 false +BU4 6.073,3.51 6.688,3.708 0.615,0.198 10 false +BU3 6.073,3.771 6.688,3.969 0.615,0.198 10 false +BU2 6.083,4.031 6.698,4.229 0.615,0.198 10 false +BU1 6.073,4.448 6.688,4.646 0.615,0.198 10 false UREL 6.073,5.208 6.688,5.406 0.615,0.198 10 false CAN+ 6.073,5.719 6.688,5.917 0.615,0.198 10 false CAN- 6.104,6.094 6.563,6.292 0.458,0.198 10 false E01 6.104,6.365 6.563,6.563 0.458,0.198 10 false E02 6.104,6.625 6.563,6.823 0.458,0.198 10 false E03 5.833,2.75 6.146,2.948 0.313,0.198 10 false 30 5.875,3.073 6.031,3.271 0.156,0.198 10 false 2 5.875,3.344 6.031,3.542 0.156,0.198 10 false 1 5.833,3.604 6.146,3.802 0.313,0.198 10 false 19 5.833,3.854 6.146,4.052 0.313,0.198 10 false 10 5.833,4.115 6.146,4.313 0.313,0.198 10 false 11 5.875,4.531 6.031,4.729 0.156,0.198 10 false 9 4.313,5.354 4.625,5.552 0.313,0.198 10 false 27 4.323,5.854 4.635,6.052 0.313,0.198 10 false 35 5.823,5.354 6.135,5.552 0.313,0.198 10 false 27 5.823,5.865 6.135,6.063 0.313,0.198 10 false 26 5.823,6.177 6.135,6.375 0.313,0.198 10 false 52 5.823,6.438 6.135,6.635 0.313,0.198 10 false 51 5.823,6.708 6.135,6.906 0.313,0.198 10 false 50 0.76,4.24 1.99,4.438 1.229,0.198 10 false DCU-MAIN 2.333,4.75 3.563,4.948 1.229,0.198 10 false DCU-MAIN 0.51,2.115 3.417,2.313 2.906,0.198 10 false STRG LOCK/AM2 NO. 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

According to the display on the GTS, select "Health Check".


d.

Check for currently output system DTCs.

Result:
Result Proceed to
DTC U010E is output A
DTC U010E and other DTCs are output* B


HINT:

*: If any other DTCs are output, perform troubleshooting for those DTCs first.




A

2.CHECK HARNESS AND CONNECTOR (UREA PUMP CONTROL ECU - ECM)

B

2.CHECK HARNESS AND CONNECTOR (UREA PUMP CONTROL ECU - ECM)
a.

Disconnect the urea pump control ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g1-27 (CAN+) - G85-27 (CANU) Always Below 1 Ω
g1-26 (CAN-) - G85-35 (CAND) Always Below 1 Ω
g1-27 (CAN+) or G85-27 (CANU) - Body ground and other terminals Always 10 kΩ or higher
g1-26 (CAN-) or G85-35 (CAND) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK UREA PUMP CONTROL ECU (BATT TERMINAL)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.CHECK UREA PUMP CONTROL ECU (BATT TERMINAL)
a.
A204368C10
0.25,1.135 0.646,1.375 0.396,0.24 2.458,1.021 2.25,1.813 true 0.25,0.167 0.427,0.344 0.177,0.177 10 false *a 1.948,1.865 2.729,2.063 0.781,0.198 10 false 30 (BATT) 0.375,1.177 0.76,1.396 0.385,0.219 10 false g1
*a Front view of wire harness connector
(to Urea Pump Control ECU)


Disconnect the urea pump control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
g1-30 (BATT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT DCU-MAIN RELAY

NG

4.INSPECT DCU-MAIN RELAY

Result:
Proceed to
OK
NG



OK

5.CHECK UREA PUMP CONTROL ECU (UREL TERMINAL)

NG

REPLACE DCU-MAIN RELAY

5.CHECK UREA PUMP CONTROL ECU (UREL TERMINAL)
a.
A381878C01
0.167,0.083 0.479,0.281 0.313,0.198 10 false *1 0.625,0.344 0.938,0.542 0.313,0.198 10 false *a
*1 No. 6 Instrument Panel Relay Block
*a Front view of wire harness connector
(to DCU-MAIN Relay)


Remove the DCU-MAIN relay from the No. 6 instrument panel relay block.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DCU-MAIN relay terminal 2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - UREA PUMP CONTROL ECU)

NG

7.CHECK HARNESS AND CONNECTOR (NO. 6 INSTRUMENT PANEL RELAY BLOCK - UREA PUMP CONTROL ECU)
6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - UREA PUMP CONTROL ECU)
A383043C01
5.083,0.531 5.417,0.74 0.333,0.208 4.229,2.156 4.948,1.167 true 4.844,2.156 5.031,1.177 true 5.458,2.156 5.635,1.156 true 5.719,1.146 5.906,0.719 5.906,0.719 6.073,0.719 true 6.281,2.177 5.719,1.24 true 0.271,0.219 0.583,0.417 0.313,0.198 10 false *1 0.427,0.865 0.74,1.063 0.313,0.198 10 false *a 3.844,0.25 4.156,0.448 0.313,0.198 10 false *b 5.167,0.542 5.479,0.74 0.313,0.198 10 false g1 3.906,2.219 4.615,2.417 0.708,0.198 10 false 1 (+BU4) 4.604,2.219 5.313,2.417 0.708,0.198 10 false 2 (+BU5) 5.313,2.219 6.021,2.417 0.708,0.198 10 false 10 (+BU2) 6.125,2.229 6.833,2.427 0.708,0.198 10 false 19 (+BU3) 6.146,0.625 6.854,0.823 0.708,0.198 10 false 11 (+BU1)
*1 No. 6 Instrument Panel Relay Block - -
*a Front view of wire harness connector
(to DCU-MAIN Relay)
*b Front view of wire harness connector
(to Urea Pump Control ECU)


a.

Remove the DCU-MAIN relay from the No. 6 instrument panel relay block.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DCU-MAIN relay terminal 3 - g1-11 (+BU1) Always Below 1 Ω
DCU-MAIN relay terminal 3 - g1-10 (+BU2) Always Below 1 Ω
DCU-MAIN relay terminal 3 - g1-19 (+BU3) Always Below 1 Ω
DCU-MAIN relay terminal 3 - g1-1 (+BU4) Always Below 1 Ω
DCU-MAIN relay terminal 3 - g1-2 (+BU5) Always Below 1 Ω
DCU-MAIN relay terminal 1 - Body ground Always Below 1 Ω
DCU-MAIN relay terminal 3 or g1-11 (+BU1) - Body ground and other terminals Always 10 kΩ or higher
DCU-MAIN relay terminal 3 or g1-10 (+BU2) - Body ground and other terminals Always 10 kΩ or higher
DCU-MAIN relay terminal 3 or g1-19 (+BU3) - Body ground and other terminals Always 10 kΩ or higher
DCU-MAIN relay terminal 3 or g1-1 (+BU4) - Body ground and other terminals Always 10 kΩ or higher
DCU-MAIN relay terminal 3 or g1-2 (+BU5) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (NO. 6 INSTRUMENT PANEL RELAY BLOCK - BATTERY)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

7.CHECK HARNESS AND CONNECTOR (NO. 6 INSTRUMENT PANEL RELAY BLOCK - UREA PUMP CONTROL ECU)
A383043C02
5.125,0.573 5.458,0.781 0.333,0.208 5.385,2.063 5.573,1.156 true 0.271,0.25 0.583,0.448 0.313,0.198 10 false *1 0.479,0.833 0.792,1.031 0.313,0.198 10 false *a 3.906,0.25 4.219,0.448 0.313,0.198 10 false *b 5.208,0.583 5.521,0.781 0.313,0.198 10 false g1 5.167,2.125 5.917,2.323 0.75,0.198 10 false 9 (UREL)
*1 No. 6 Instrument Panel Relay Block - -
*a Front view of wire harness connector
(to DCU-MAIN Relay)
*b Front view of wire harness connector
(to Urea Pump Control ECU)


a.

Remove the DCU-MAIN relay from the No. 6 instrument panel relay block.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DCU-MAIN relay terminal 2 - g1-9 (UREL) Always Below 1 Ω
DCU-MAIN relay terminal 2 or g1-9 (UREL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR