Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _053992 STOP AND START _0262513 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P161D  Starter Delay Circuit  


DESCRIPTION

By using the starter delay circuit, the engine stop and start ECU can activate the ST NO. 2 relay (for starter motor operation) after activating the ST NO. 1 relay (for starter pinion operation) to operate the starter assembly.

By monitoring the condition of the ST NO. 1 relay (for starter pinion operation) and ST NO. 2 relay (for starter motor operation), the engine stop and start ECU detects if the transistor of the starter delay circuit is stuck. If the transistor of the starter delay circuit is stuck on, the engine stop and start ECU blinks the stop and start cancel indicator light and stores DTC P161D. If the transistor of the starter delay circuit is stuck on, the ST NO. 1 relay (for starter pinion operation) and ST NO. 2 relay (for starter motor operation) will be activated simultaneously.

w/ Entry and Start System:
A346405E04
0.083,0.052 2.677,0.302 2.594,0.25 12 false for Automatic Transmission: 0.615,0.698 2.646,0.917 2.031,0.219 10 false BBC NO. 3 1.552,1.104 2.917,1.302 1.365,0.198 10 false BBC NO. 1 4.917,0.417 5.531,0.615 0.615,0.198 10 false BIN1 4.927,0.823 5.542,1.021 0.615,0.198 10 false BIN2 2.344,1.896 3.677,2.271 1.333,0.375 10 false Park/Neutral Position Switch Assembly 0.417,1.771 1.948,2.167 1.531,0.396 10 false Certification ECU (Smart Key ECU Assembly) 1.063,1.406 1.677,1.604 0.615,0.198 10 false STAR 2.552,1.188 2.708,1.385 0.156,0.198 10 false L 2.542,1.427 2.698,1.625 0.156,0.198 10 false B 2.781,1.656 2.938,1.854 0.156,0.198 10 false P 3.021,1.656 3.177,1.854 0.156,0.198 10 false N 4.917,2.479 5.375,2.677 0.458,0.198 10 false STA 4.948,3.375 5.406,3.573 0.458,0.198 10 false STA2 3.615,3.01 4.375,3.208 0.76,0.198 10 false ST NO. 1 0.698,2.802 1.927,3 1.229,0.198 10 false ST NO. 1 0.688,3.677 1.917,3.875 1.229,0.198 10 false ST NO. 2 2.146,4.719 2.896,4.938 0.75,0.219 10 false ST NO. 2 0.469,4.802 1.542,5 1.073,0.198 10 false FL MAIN 0.563,7.302 1.635,7.5 1.073,0.198 10 false Battery 5.063,3.833 6.792,4.073 1.729,0.24 10 false Engine Stop and Start ECU 4.865,8.375 6.063,8.583 1.198,0.208 10 false Starter Assembly 3.99,4.344 4.25,4.542 0.26,0.198 10 false ST 3.979,4.958 4.135,5.156 0.156,0.198 10 false B 3.979,6.448 4.438,6.646 0.458,0.198 10 false SL2 4,7.406 4.458,7.604 0.458,0.198 10 false SL1 5.25,5.458 5.406,5.656 0.156,0.198 10 false L 5.24,5.906 5.396,6.104 0.156,0.198 10 false B 5.302,6.146 5.458,6.344 0.156,0.198 10 false M

w/o Entry and Start System:
A346914E02
3.115,0.698 4.354,0.938 1.24,0.24 10 false BBC NO. 3 4.917,0.438 5.531,0.635 0.615,0.198 10 false BIN1 4.927,0.813 5.542,1.01 0.615,0.198 10 false BIN2 3.063,1.906 4.385,2.406 1.323,0.5 10 false Park/Neutral Position Switch Assembly 0.563,1.219 1.667,1.677 1.104,0.458 10 false Ignition or Starter Switch Assembly 1.323,0.875 1.781,1.073 0.458,0.198 10 false ST2 0.677,0.969 1.135,1.167 0.458,0.198 10 false AM2 2.396,1.104 3.167,1.292 0.771,0.188 10 false BBC NO. 1 4.906,2.49 5.365,2.688 0.458,0.198 10 false STA 4.927,3.406 5.542,3.604 0.615,0.198 10 false STA2 3.635,3.021 4.479,3.219 0.844,0.198 10 false ST NO. 1 5.021,3.844 6.833,4.073 1.813,0.229 10 false Engine Stop and Start ECU 0.698,2.771 1.927,2.969 1.229,0.198 10 false ST NO. 1 2.135,4.719 3.365,4.917 1.229,0.198 10 false ST NO. 2 0.698,3.677 1.927,3.875 1.229,0.198 10 false ST NO. 2 0.552,7.292 1.625,7.49 1.073,0.198 10 false Battery 4.719,8.385 6.01,8.583 1.292,0.198 10 false Starter Assembly 3.979,4.354 4.229,4.552 0.25,0.198 10 false ST 3.99,4.948 4.146,5.146 0.156,0.198 10 false B 5.208,5.458 5.365,5.656 0.156,0.198 10 false L 5.198,5.927 5.354,6.125 0.156,0.198 10 false B 5.281,6.146 5.438,6.344 0.156,0.198 10 false M 3.979,6.438 4.438,6.635 0.458,0.198 10 false SL2 3.99,7.406 4.448,7.604 0.458,0.198 10 false SL1 3.365,1.198 3.521,1.396 0.156,0.198 10 false L 3.365,1.427 3.521,1.625 0.156,0.198 10 false B 3.594,1.656 3.75,1.854 0.156,0.198 10 false P 3.833,1.656 3.99,1.854 0.156,0.198 10 false N 0.542,2.156 2.229,2.365 1.688,0.208 10 false STRG LOCK/AM2 NO. 1 0.479,4.813 1.552,5.01 1.073,0.198 10 false FL MAIN 0.063,0.052 3.146,0.375 3.083,0.323 12 false for Automatic Transmission:

w/ Entry and Start System:
A382131E01
0.083,0.063 3,0.406 2.917,0.344 12 false for Manual Transmission: 0.667,0.698 1.438,0.885 0.771,0.188 10 false BBC NO. 3 1.552,1.094 2.323,1.281 0.771,0.188 10 false BBC NO. 1 1.042,1.417 1.813,1.604 0.771,0.188 10 false STAR 0.49,1.792 2.042,2.188 1.552,0.396 10 false Certification ECU (Smart Key ECU Assembly) 2.583,1.729 4.042,2.125 1.458,0.396 10 false Clutch Start Switch Assembly (for Lower) 4.896,0.417 5.26,0.615 0.365,0.198 10 false BIN1 4.896,0.823 5.26,1.021 0.365,0.198 10 false BIN2 4.896,2.469 5.26,2.667 0.365,0.198 10 false STA 4.885,3.385 5.385,3.583 0.5,0.198 10 false STA2 5.01,3.823 6.833,4.052 1.823,0.229 10 false Engine Stop and Start ECU 3.604,2.99 4.375,3.177 0.771,0.188 10 false ST NO. 1 2.135,4.74 2.906,4.927 0.771,0.188 10 false ST NO. 2 0.688,3.656 1.458,3.844 0.771,0.188 10 false ST NO. 2 0.677,2.781 1.448,2.969 0.771,0.188 10 false ST NO. 1 0.479,4.802 1.25,4.99 0.771,0.188 10 false FL MAIN 3.969,4.344 4.281,4.542 0.313,0.198 10 false ST 3.979,4.938 4.292,5.135 0.313,0.198 10 false B 5.229,5.49 5.542,5.688 0.313,0.198 10 false L 5.229,5.906 5.542,6.104 0.313,0.198 10 false B 5.292,6.146 5.604,6.344 0.313,0.198 10 false M 3.969,6.448 4.74,6.635 0.771,0.188 10 false SL2 3.979,7.427 4.75,7.615 0.771,0.188 10 false SL1 0.531,7.313 1.302,7.5 0.771,0.188 10 false Battery 4.219,8.354 5.615,8.615 1.396,0.26 10 false Starter Assembly

w/o Entry and Start System:
A382132E01
0.063,0.063 2.167,0.344 2.104,0.281 12 false for Manual Transmission: 2.906,1.719 4.427,2.104 1.521,0.385 10 false Clutch Start Switch Assembly (for Lower) 0.583,1.365 1.74,1.792 1.156,0.427 10 false Ignition or Starter Switch Assembly 0.563,2.156 2.208,2.354 1.646,0.198 10 false STRG LOCK/AM2 NO. 1 3.094,0.698 3.917,0.896 0.823,0.198 10 false BBC NO. 3 2.396,1.083 3.219,1.281 0.823,0.198 10 false BBC NO. 1 4.906,0.813 5.729,1.01 0.823,0.198 10 false BIN2 0.656,2.781 1.479,2.979 0.823,0.198 10 false ST NO. 1 0.646,3.677 1.469,3.875 0.823,0.198 10 false ST NO. 2 2.115,4.708 2.938,4.906 0.823,0.198 10 false ST NO. 2 0.458,4.792 1.281,4.99 0.823,0.198 10 false FL MAIN 0.531,7.281 1.354,7.479 0.823,0.198 10 false Battery 4.521,8.365 5.719,8.615 1.198,0.25 10 false Starter Assembly 5.01,3.844 6.813,4.104 1.802,0.26 10 false Engine Stop and Start ECU 4.917,0.406 5.74,0.604 0.823,0.198 10 false BIN1 4.906,2.458 5.729,2.656 0.823,0.198 10 false STA 4.906,3.375 5.729,3.573 0.823,0.198 10 false STA2 3.958,4.333 4.781,4.531 0.823,0.198 10 false ST 3.969,4.917 4.792,5.115 0.823,0.198 10 false B 5.188,5.479 6.01,5.677 0.823,0.198 10 false L 5.188,5.906 6.01,6.104 0.823,0.198 10 false B 5.25,6.135 6.073,6.333 0.823,0.198 10 false M 3.979,6.448 4.802,6.646 0.823,0.198 10 false SL2 4,7.417 4.823,7.615 0.823,0.198 10 false SL1 0.677,1.094 1.094,1.323 0.417,0.229 10 false AM2 1.271,1.104 1.688,1.333 0.417,0.229 10 false ST2

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P161D Starter Delay Circuit Both of the following conditions are met (1 trip detection logic):
·

Ignition switch ON

·

Time between ST NO. 1 relay (for starter pinion) turning on and ST NO. 2 relay (for starter motor) turning on becomes less than 0.016 seconds and 3 times or more


Engine stop and start ECU Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle with the battery temperature at 11°C (51°F) or higher for 5 to 60 minutes to complete the refresh charge. (The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode".)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again.

If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



f.

for Automatic Transmission:

Depress the brake pedal and stop the vehicle.

for Manual Transmission:

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Keep the engine stopped by stop and start control. (for Automatic Transmission: Keep the shift lever in D.)


h.

for Automatic Transmission:

Release the brake pedal with the shift lever in D to start the engine.

for Manual Transmission:

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.



i.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



j.

for Automatic Transmission:

Depress the brake pedal and stop the vehicle.

for Manual Transmission:

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


k.

Keep the engine stopped by stop and start control. (for Automatic Transmission: Keep the shift lever in D.)


l.

for Automatic Transmission:

Release the brake pedal with the shift lever in D to start the engine.

for Manual Transmission:

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.



m.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



n.

for Automatic Transmission:

Depress the brake pedal and stop the vehicle.

for Manual Transmission:

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


o.

Keep the engine stopped by stop and start control. (for Automatic Transmission: Keep the shift lever in D.)


p.

for Automatic Transmission:

Release the brake pedal with the shift lever in D to start the engine.

for Manual Transmission:

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.



q.

Check that no DTCs are output.



STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle with the battery temperature at 11°C (51°F) or higher for 5 to 60 minutes to complete the refresh charge. (The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode".)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again.

If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

for Automatic Transmission:

Depress the brake pedal and stop the vehicle.

for Manual Transmission:

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control. (for Automatic Transmission: Keep the shift lever in D.)


f.

for Automatic Transmission:

Release the brake pedal with the shift lever in D to start the engine.

for Manual Transmission:

Depress the clutch pedal and start the engine.



CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and total number of engine starts and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

for Automatic Transmission:

When the engine stop and start ECU is replaced, check the electromagnetic oil pump.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA


PROCEDURE

1.CHECK ENGINE STOP AND START ECU (STA, STA2 SIGNAL)
a.

Connect an oscilloscope to terminals G126-21 (STA), G126-23 (STA2) and G126-6 (DGND).

A346331C94
3.188,0.615 3.708,0.844 0.521,0.229 3.427,1.344 3.469,2.198 true 3.271,1.333 2.708,2.188 true 3.74,1.229 4.563,2.281 true 3.271,0.646 3.729,0.844 0.458,0.198 10 false G126 3.354,2.25 3.719,2.458 0.365,0.208 10 false STA 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a 2.542,2.24 3.156,2.438 0.615,0.198 10 false STA2 4.427,2.313 5.042,2.51 0.615,0.198 10 false DGND
*a Component with harness connected
(Engine Stop and Start ECU)
- -



b.
A285702E13
0.042,0.677 0.5,0.875 0.458,0.198 10 false STA 0.042,1.281 0.5,1.479 0.458,0.198 10 false STA2 1.198,1.771 2.958,1.958 1.76,0.188 10 false 0.016 seconds or more 0.021,0.875 1.854,1.073 1.833,0.198 10 false (ST NO. 1 Relay) 0.031,1.458 1.865,1.656 1.833,0.198 10 false (ST NO. 2 Relay)

Check the waveform immediately after turning the engine starts.

Item Condition
Tester Connection G126-21 (STA) - G126-6 (DGND)
G126-23 (STA2) - G126-6 (DGND)
Condition Engine started by ignition or starter switch assembly (w/o Entry and Start System) or push start switch assembly (w/ Entry and Start System) operation

Result:
Result Proceed to
Time between ST NO. 1 relay (for starter pinion) turning on and ST NO. 2 relay (for starter motor) turning on becomes 0.016 seconds or more A
Time between ST NO. 1 relay (for starter pinion) turning on and ST NO. 2 relay (for starter motor) turning on becomes less than 0.016 seconds B




A

B