Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _053992 STOP AND START _0262513 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  B22C0  BBC Overcurrent  


DESCRIPTION

A backup boost converter is built into the engine stop and start ECU.

The backup boost converter helps maintain battery voltage to prevent various functions from failing if power source voltage supplied from the backup boost converter drops due to the high electrical load when the engine is restarted by stop and start control.

The backup boost converter helps maintain the power source voltage if the battery voltage drops due to the high electrical load when the engine is restarted by stop and start control.

HINT:

A relay function and fuse function are provided in the backup boost converter.

If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).

When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.

The fuse function is reset* when the ignition switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the ignition switch is turned to ON.

*: A semiconductor fuse self-resets according to electric signals.


The backup boost converter supplies power to:
·

Radio and display receiver assembly

·

Air conditioning control assembly

·

Skid control ECU (brake actuator assembly)

·

Spiral with sensor cable sub-assembly

·

Combination meter assembly

·

Millimeter wave radar sensor assembly

·

Forward recognition camera

·

Body ECU


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
B22C0 BBC Overcurrent The following condition continues for 1 second or more (1 trip detection logic):
·

Overcurrent is detected at the B42 and IG41 terminals in the engine stop and start ECU


·

Engine stop and start ECU

·

Wire harness or connector

·

Radio & display receiver assembly

·

Air conditioning control assembly

·

Millimeter wave radar sensor assembly

·

Forward recognition camera

·

Body ECU


Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle with the battery temperature at 11°C (51°F) or higher for 5 to 60 minutes to complete the refresh charge. (The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode".)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again.

If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



f.

for Automatic Transmission:

Depress the brake pedal and stop the vehicle.

for Manual Transmission:

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Keep the engine stopped by stop and start control for 1 second or more. (for Automatic Transmission: Keep the shift lever in D.)


h.

for Automatic Transmission:

Release the brake pedal with the shift lever in D to start the engine.

for Manual Transmission:

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.



i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle with the battery temperature at 11°C (51°F) or higher for 5 to 60 minutes to complete the refresh charge. (The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode".)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again.

If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

for Automatic Transmission:

Depress the brake pedal and stop the vehicle.

for Manual Transmission:

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control. (for Automatic Transmission: Keep the shift lever in D.)


f.

for Automatic Transmission:

Release the brake pedal with the shift lever in D to start the engine.

for Manual Transmission:

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A381893E01
2.073,8.469 4.938,8.74 2.865,0.271 10 false Certification ECU (Smart Key ECU Assembly) 0.552,7.667 1.177,7.896 0.625,0.229 10 false Battery 0.375,7.094 1.083,7.302 0.708,0.208 10 false FL MAIN 0.375,6.219 1,6.448 0.625,0.229 10 false J/B-B 2.188,6.469 3.031,6.698 0.844,0.229 10 false BBC NO. 3 1.969,7.115 2.594,7.344 0.625,0.229 10 false SMART 3.229,6.906 4.104,7.135 0.875,0.229 10 false BBC NO. 1 1.531,4.865 2.375,5.094 0.844,0.229 10 false IG1 NO. 1 3.885,5.021 4.729,5.25 0.844,0.229 10 false IG2 2.26,7.646 2.885,7.875 0.625,0.229 10 false +B 2.854,7.635 3.479,7.865 0.625,0.229 10 false IG1D 2.771,8.021 3.396,8.25 0.625,0.229 10 false ACCD 3.719,4.667 3.958,4.875 0.24,0.208 10 false 1 2.646,6.146 2.885,6.354 0.24,0.208 10 false 2 3.188,5.417 3.427,5.625 0.24,0.208 10 false 3 3.188,4.656 3.427,4.865 0.24,0.208 10 false 5 2.385,6.146 2.625,6.354 0.24,0.208 10 false 1 3.396,6.625 3.635,6.833 0.24,0.208 10 false 1 3.677,6.625 3.917,6.833 0.24,0.208 10 false 2 3.729,5.427 3.969,5.635 0.24,0.208 10 false 2 1.385,5.271 1.625,5.479 0.24,0.208 10 false 2 1.375,4.5 1.615,4.708 0.24,0.208 10 false 1 0.865,4.5 1.104,4.708 0.24,0.208 10 false 3 0.844,5.26 1.083,5.469 0.24,0.208 10 false 5 2.073,7.781 2.313,7.99 0.24,0.208 10 false 1 3.26,7.75 3.5,7.958 0.24,0.208 10 false 20 3.26,8.135 3.5,8.344 0.24,0.208 10 false 21 5.625,6.052 5.865,6.26 0.24,0.208 10 false 3 5.625,6.552 5.865,6.76 0.24,0.208 10 false 1 5.49,6.292 5.917,6.5 0.427,0.208 10 false G125 5.5,6.75 5.927,6.958 0.427,0.208 10 false G125 5.906,6.75 6.333,6.958 0.427,0.208 10 false BIN2 5.917,6.313 6.344,6.521 0.427,0.208 10 false BIN1 5.917,0.885 6.542,1.115 0.625,0.229 10 false ACC 5.917,1.844 6.76,2.073 0.844,0.229 10 false IG1 5.917,2.281 6.76,2.51 0.844,0.229 10 false IG2 2.073,8.313 4.938,8.583 2.865,0.271 10 false G69 5.344,7.552 7.094,7.813 1.75,0.26 10 false Engine Stop and Start ECU 1.458,3.604 4.323,3.875 2.865,0.271 10 false Instrument Panel Junction Block Assembly 5.573,0.677 5.813,0.885 0.24,0.208 10 false 19 5.594,1.625 5.833,1.833 0.24,0.208 10 false 21 5.573,2.073 5.813,2.281 0.24,0.208 10 false 18 5.5,2.281 5.927,2.49 0.427,0.208 10 false G127 5.5,1.823 5.927,2.031 0.427,0.208 10 false G127 5.49,0.885 5.917,1.094 0.427,0.208 10 false G127 3.094,1.052 4.198,1.25 1.104,0.198 10 false SFT LOCK-ACC 4.885,1.042 5.51,1.271 0.625,0.229 10 false ACC 2.583,1.604 3.208,1.833 0.625,0.229 10 false ACC 0.219,1.896 0.844,2.125 0.625,0.229 10 false ALT 2.396,3.281 3.021,3.51 0.625,0.229 10 false AM1 2.875,2.854 3.833,3.083 0.958,0.229 10 false AM2 NO. 2 2.521,2.438 3.479,2.667 0.958,0.229 10 false METER 3,1.969 3.958,2.198 0.958,0.229 10 false IG1 NO. 3 1.365,0.677 1.604,0.885 0.24,0.208 10 false 1*1 1.781,0.698 2.021,0.906 0.24,0.208 10 false 1*2 1.375,1.604 1.615,1.813 0.24,0.208 10 false 1 1.385,2.073 1.625,2.281 0.24,0.208 10 false 1 1.375,2.5 1.615,2.708 0.24,0.208 10 false 1 1.385,1.125 1.625,1.333 0.24,0.208 10 false 5 1.323,0.896 1.948,1.125 0.625,0.229 10 false 2A 1.333,1.302 1.958,1.531 0.625,0.229 10 false 2J 1.344,1.813 1.969,2.042 0.625,0.229 10 false 2E 1.323,2.281 1.948,2.51 0.625,0.229 10 false 2G 1.333,2.698 1.958,2.927 0.625,0.229 10 false 2B 1.708,0.906 2.333,1.135 0.625,0.229 10 false 2R 4.323,0.698 4.563,0.906 0.24,0.208 10 false 5 4.323,1.104 4.563,1.313 0.24,0.208 10 false 2 4.313,2.948 4.552,3.156 0.24,0.208 10 false 2 4.302,2.5 4.542,2.708 0.24,0.208 10 false 6 4.313,2.083 4.552,2.292 0.24,0.208 10 false 6 4.302,1.615 4.542,1.823 0.24,0.208 10 false 1 4.271,0.917 4.896,1.146 0.625,0.229 10 false 2P 4.281,1.313 4.906,1.542 0.625,0.229 10 false 2E 4.271,1.823 4.896,2.052 0.625,0.229 10 false 2C 4.26,2.281 4.885,2.51 0.625,0.229 10 false 2P 4.271,2.698 4.896,2.927 0.625,0.229 10 false 2G 4.271,3.146 4.896,3.375 0.625,0.229 10 false 2F 0.146,0.073 2.74,0.385 2.594,0.313 12 false w/ Entry and Start System: 5.521,8.063 6.688,8.271 1.167,0.208 10 false *1: for LHD 5.531,8.354 6.698,8.563 1.167,0.208 10 false *2: for RHD

A381891E01
1.927,8.083 2.76,8.281 0.833,0.198 10 false *1: for LHD 0.521,8.031 1.104,8.24 0.583,0.208 10 false Battery 0.396,7.417 1.063,7.615 0.667,0.198 10 false FL MAIN 0.802,7.146 2.438,7.344 1.635,0.198 10 false STRG LOCK/AM2 NO. 1 0.115,0.094 2.906,0.323 2.792,0.229 12 false w/o Entry and Start System: 1.719,3.646 4.469,3.875 2.75,0.229 10 false Instrument Panel Junction Block Assembly 1.302,0.896 1.594,1.083 0.292,0.188 10 false 2A 1.323,1.427 1.615,1.615 0.292,0.188 10 false 2J 1.323,2.052 1.615,2.24 0.292,0.188 10 false 2E 1.292,2.594 1.583,2.781 0.292,0.188 10 false 2G 4.125,0.896 4.417,1.083 0.292,0.188 10 false 2P 4.135,1.406 4.427,1.594 0.292,0.188 10 false 2E 4.135,2.052 4.427,2.24 0.292,0.188 10 false 2C 4.125,2.583 4.417,2.771 0.292,0.188 10 false 2P 4.135,3.115 4.427,3.302 0.292,0.188 10 false 2F 3.115,3.26 3.531,3.458 0.417,0.198 10 false AM1 2.563,2.75 3.26,2.948 0.698,0.198 10 false METER 3.052,2.219 3.813,2.417 0.76,0.198 10 false IG1 NO. 3 2.927,1.052 4.104,1.25 1.177,0.198 10 false SFT LOCK-ACC 2.406,1.729 2.844,1.958 0.438,0.229 10 false ACC 4.76,1.052 5.198,1.281 0.438,0.229 10 false ACC 5.385,7.625 7.094,7.854 1.708,0.229 10 false Engine Stop and Start ECU 0.375,4.927 0.771,5.146 0.396,0.219 10 false ALT 2.896,4.969 3.74,5.198 0.844,0.229 10 false BBC NO. 3 3.219,5.615 4.063,5.844 0.844,0.229 10 false BBC NO. 1 2.427,7.406 2.823,7.625 0.396,0.219 10 false G1 1.75,0.698 2.042,0.885 0.292,0.188 10 false 1 1.354,1.24 1.646,1.427 0.292,0.188 10 false 5 1.365,1.833 1.656,2.021 0.292,0.188 10 false 1 1.354,2.375 1.646,2.563 0.292,0.188 10 false 1 4.167,0.688 4.458,0.875 0.292,0.188 10 false 5 4.188,1.208 4.406,1.375 0.219,0.167 10 false 2 4.167,1.854 4.385,2.021 0.219,0.167 10 false 1 4.156,2.396 4.375,2.563 0.219,0.167 10 false 6 4.167,2.906 4.385,3.073 0.219,0.167 10 false 2 5.583,0.688 5.875,0.875 0.292,0.188 10 false 19 5.917,0.896 6.354,1.125 0.438,0.229 10 false ACC 5.5,0.896 5.948,1.094 0.448,0.198 10 false G127 5.49,2.052 5.979,2.24 0.49,0.188 10 false G127 5.5,2.594 5.927,2.781 0.427,0.188 10 false G127 5.927,2.052 6.365,2.281 0.438,0.229 10 false IG1 5.948,2.594 6.385,2.823 0.438,0.229 10 false IG2 5.573,1.833 5.865,2.021 0.292,0.188 10 false 21 5.573,2.385 5.865,2.573 0.292,0.188 10 false 18 5.49,4.802 5.948,5.01 0.458,0.208 10 false G125 5.5,5.448 5.948,5.635 0.448,0.188 10 false G125 5.625,5.229 5.917,5.417 0.292,0.188 10 false 1 5.594,4.573 5.885,4.76 0.292,0.188 10 false 3 5.917,4.802 6.354,5.031 0.438,0.229 10 false BIN1 5.917,5.458 6.354,5.688 0.438,0.229 10 false BIN2 2.74,6.385 3.177,6.583 0.438,0.198 10 false AM1 2.74,6.875 3.198,7.083 0.458,0.208 10 false AM2 2.542,6.615 2.813,6.802 0.271,0.188 10 false 5 3.5,6.125 3.938,6.354 0.438,0.229 10 false ACC 3.542,6.375 3.979,6.604 0.438,0.229 10 false IG1 3.552,6.875 3.99,7.104 0.438,0.229 10 false IG2 2.552,7.094 2.823,7.281 0.271,0.188 10 false 4 3.885,6.354 4.156,6.542 0.271,0.188 10 false 7 3.896,6.604 4.167,6.792 0.271,0.188 10 false 8 3.896,7.104 4.167,7.292 0.271,0.188 10 false 3 3.344,5.271 3.635,5.458 0.292,0.188 10 false 1 2.979,4.677 3.271,4.865 0.292,0.188 10 false 1 3.271,4.677 3.49,4.844 0.219,0.167 10 false 2 3.604,5.271 3.823,5.438 0.219,0.167 10 false 2 1.354,0.688 1.646,0.875 0.292,0.188 10 false 1 1.708,0.906 2,1.094 0.292,0.188 10 false 2R 2.427,7.594 4.708,7.792 2.281,0.198 10 false Ignition or Starter Switch Assembly 1.917,8.396 2.833,8.594 0.917,0.198 10 false *2: for RHD 1.354,1.104 1.646,1.292 0.292,0.188 10 false *1 1.719,1.094 2.01,1.281 0.292,0.188 10 false *2

A381892E01
0.813,8.719 3.531,8.979 2.719,0.26 10 false Instrument Panel Junction Block Assembly 1.406,8.188 2.177,8.406 0.771,0.219 10 false Body ECU 2.281,7.75 2.5,7.979 0.219,0.229 10 false IG 2.635,7.74 2.906,7.948 0.271,0.208 10 false A 3.458,7.75 3.802,7.958 0.344,0.208 10 false 2D 2.646,7.542 2.865,7.771 0.219,0.229 10 false 7 3.521,7.531 3.74,7.76 0.219,0.229 10 false 5 5.875,7.271 6.469,7.479 0.594,0.208 10 false GND2 5.563,7.073 5.781,7.302 0.219,0.229 10 false 2 5.448,7.281 5.938,7.49 0.49,0.208 10 false G125 5.438,7.896 5.938,8.115 0.5,0.219 10 false G125 5.448,8.583 5.969,8.792 0.521,0.208 10 false G126 5.573,7.677 5.792,7.906 0.219,0.229 10 false 8 5.573,8.365 5.792,8.594 0.219,0.229 10 false 6 5.885,7.906 6.479,8.115 0.594,0.208 10 false GND1 5.885,8.594 6.479,8.802 0.594,0.208 10 false DGND 5.448,3.375 5.958,3.583 0.51,0.208 10 false G127 5.563,0.979 5.781,1.208 0.219,0.229 10 false 1 5.875,1.198 6.469,1.406 0.594,0.208 10 false IG31 0.552,3.958 2.906,4.198 2.354,0.24 10 false Air Conditioning Control Assembly 0.677,2.396 3.75,2.625 3.073,0.229 10 false Skid Control ECU (Brake Actuator Assembly) 0.75,1 3.281,1.26 2.531,0.26 10 false Spiral with Sensor Cable Sub-assembly 0.76,0.823 1.104,1.031 0.344,0.208 10 false G21 2.292,0.438 2.885,0.646 0.594,0.208 10 false IG 2.531,0.573 2.75,0.802 0.219,0.229 10 false 4 0.688,2.219 1.031,2.427 0.344,0.208 10 false A4 2.25,1.833 2.844,2.042 0.594,0.208 10 false IG1 2.542,1.948 2.76,2.177 0.219,0.229 10 false 12 5.448,1.177 5.99,1.385 0.542,0.208 10 false G127 5.875,3.385 6.469,3.594 0.594,0.208 10 false IG41 5.573,3.167 5.792,3.396 0.219,0.229 10 false 3 0.563,3.781 0.906,3.99 0.344,0.208 10 false G32 2.208,3.385 2.802,3.594 0.594,0.208 10 false IG+ 2.563,3.521 2.781,3.75 0.219,0.229 10 false 2 0.552,5.417 3.521,5.667 2.969,0.25 10 false Millimeter wave radar sensor assembly 0.563,5.24 0.906,5.448 0.344,0.208 10 false A64 0.792,6.771 3.146,7.01 2.354,0.24 10 false Forward recognition camera 0.792,6.615 1.135,6.823 0.344,0.208 10 false Q4 2.219,4.75 2.813,4.958 0.594,0.208 10 false IGB 2.219,6.156 2.813,6.365 0.594,0.208 10 false IGB 2.552,4.906 2.771,5.135 0.219,0.229 10 false 8 2.542,6.292 2.76,6.521 0.219,0.229 10 false 7

A346422E03
0.552,1.823 2.479,2.063 1.927,0.24 10 false Combination Meter Assembly 2.354,1.208 2.813,1.406 0.458,0.198 10 false IG+ 5.823,1.219 6.438,1.417 0.615,0.198 10 false IG12 5.375,1.219 5.833,1.417 0.458,0.198 10 false G127 5.458,1.021 5.771,1.219 0.313,0.198 10 false 10 5.823,2.625 6.438,2.823 0.615,0.198 10 false B42 5.375,2.635 5.833,2.833 0.458,0.198 10 false G127 5.458,2.427 5.771,2.625 0.313,0.198 10 false 12 5.823,3.344 6.438,3.542 0.615,0.198 10 false AC42 5.375,3.354 5.833,3.552 0.458,0.198 10 false G127 5.469,3.135 5.781,3.333 0.313,0.198 10 false 15 2.271,2.635 2.729,2.833 0.458,0.198 10 false +B1 2.177,3.344 2.792,3.542 0.615,0.198 10 false ACC1 5.281,4.365 7.094,4.625 1.813,0.26 10 false Engine Stop and Start ECU 2.719,2.5 2.875,2.698 0.156,0.198 10 false 4 2.708,3.208 2.865,3.406 0.156,0.198 10 false 3 0.552,1.615 0.865,1.813 0.313,0.198 10 false G9 2.74,1.073 3.052,1.271 0.313,0.198 10 false 22 0.229,3.969 2.854,4.198 2.625,0.229 10 false Radio and Display Receiver Assembly 0.24,3.781 0.698,3.979 0.458,0.198 10 false G40

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and total number of engine starts and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

for Automatic Transmission:

When the engine stop and start ECU is replaced, check the electromagnetic oil pump.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

If electrical load from additional devices installed on the vehicle (aftermarket audio system, etc.) is applied to the B42 or IG41 terminal in the engine stop and start ECU, the fuse function of the backup boost converter may operate.

If the fuse function of the backup boost converter operates, any systems connected to the B42 or IG41 terminal in the engine stop and start ECU will not operate.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC FUSE)
a.

Disconnect the G125 engine stop and start ECU connector.


b.

Remove the BBC NO. 1 and BBC NO. 3 fuses from the engine room relay block and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G125-1 (BIN2) - BBC NO. 1 fuse terminal 2 Always Below 1 Ω
G125-3 (BIN1) - BBC NO. 3 fuse terminal 2 Always Below 1 Ω
G125-1 (BIN2) - Body ground Always 10 kΩ or higher
G125-3 (BIN1) - Body ground Always 10 kΩ or higher
BBC NO. 1 fuse terminal 2 - Body ground Always 10 kΩ or higher
BBC NO. 3 fuse terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the G127 engine stop and start ECU connector.


b.

Disconnect the G40 radio and display receiver assembly connector.


c.

Disconnect the G32 air conditioning control assembly connector.


d.

Disconnect the A64 millimeter wave radar sensor assembly connector.


e.

Disconnect the Q4 forward recognition camera connector.


f.

Disconnect the 2D instrument panel junction block assembly connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G127-12 (B42) - G40-4 (+B1) Always Below 1 Ω
G127-3 (IG41) - G32-2 (IG+) Always Below 1 Ω
G127-3 (IG41) - A64-8 (IGB) Always Below 1 Ω
G127-3 (IG41) - Q4-7 (IGB) Always Below 1 Ω
G127-3 (IG41) - 2D-5 Always Below 1 Ω
G127-12 (B42) - Body ground Always 10 kΩ or higher
G127-3 (IG41) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU
a.

Disconnect the engine stop and start ECU connector.

A381876C01
1.385,0.115 1.917,0.448 0.531,0.333 3.063,0.115 3.594,0.448 0.531,0.333 4.948,0.115 5.479,0.448 0.531,0.333 0.573,1.948 1.104,2.281 0.531,0.333 2.656,1.948 3.188,2.281 0.531,0.333 5.427,1.948 5.958,2.281 0.531,0.333 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.479,0.208 1.938,0.406 0.458,0.198 10 false G125 3.167,0.208 3.656,0.427 0.49,0.219 10 false G126 5.052,0.208 5.5,0.438 0.448,0.229 10 false G127 0.656,2.042 1.115,2.24 0.458,0.198 10 false G125 2.75,2.042 3.24,2.26 0.49,0.219 10 false G126 5.521,2.042 5.969,2.271 0.448,0.229 10 false G127
*a Component without harness connected
(Engine Stop and Start ECU)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G127-12 (B42) - G126-6 (DGND) Always 10 kΩ or higher
G127-3 (IG41) - G126-6 (DGND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK VEHICLE CONDITION (B42, IG41 CIRCUIT)

NG

4.CHECK VEHICLE CONDITION (B42, IG41 CIRCUIT)
a.

Check that additional devices installed to the vehicle (aftermarket audio system, etc.) are not connected to the B42 or IG41 terminal circuit in the engine stop and start ECU.

Result:
Result Proceed to
Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is not applied. A
Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is applied. B




A

GO TO TROUBLE AREAS (TROUBLESHOOTING PROCEDURE FOR ECUS CONNECTED TO B42 AND IG41 TERMINALS)

B

END (REMOVE ELECTRICAL LOAD FROM ADDITIONAL DEVICE)