Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _053992 STOP AND START _0262513 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P1862  Clutch Control System 2  


DESCRIPTION

There are 2 clutch pedal switches for the clutch pedal. The clutch switch assembly (for upper) is used for stopping and restarting of the engine by stop and start control. During the stop and start control, the clutch start switch assembly (for lower) is used only when the clutch switch assembly (for upper) is stuck on or the fail-safe function is activated.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1862 Clutch Control System 2 Both of the following conditions continue for 0.5 seconds or more (1 trip detection logic):
·

Clutch start switch assembly (for lower) is on.

·

Clutch switch assembly (for upper) is on.


·

Clutch start switch assembly (for lower)

·

Clutch switch assembly (for upper)

·

Wire harness or connector

·

Engine stop and start ECU


Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle with the battery temperature at 11°C (51°F) or higher for 5 to 60 minutes to complete the refresh charge. (The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode".)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again.

If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine.


e.
A206932E04
1.302,1.948 1.302,2.708 false 1.594,1.948 1.594,2.708 false 1.323,2.167 1.865,2.167 false 1.365,2.208 1.323,2.167 1.323,2.167 1.365,2.135 false 1.823,2.135 1.865,2.167 1.865,2.167 1.823,2.208 false 1.708,2.167 1.958,2.74 false 1.469,2.167 1.208,2.74 false 1.542,2.135 1.594,2.167 1.594,2.167 1.542,2.208 false 1.635,2.208 1.594,2.167 1.594,2.167 1.635,2.135 false 1.875,1.927 1.875,2.708 false 0.135,0.115 1.458,0.302 1.323,0.188 10 Clutch Switch Signal 1.99,2.719 3.135,2.906 1.146,0.188 10 1 second or more 0.281,2.719 1.052,3.031 0.771,0.313 10 1 second or more 0.583,1.177 0.833,1.333 0.25,0.156 10 ON 0.583,1.854 0.896,2.01 0.313,0.156 10 OFF

Fully depress the clutch pedal for 1 second or more. Release the clutch pedal and wait for at least 1 second.


f.

Repeat the previous step 3 times.


g.

Check that no DTCs are output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle with the battery temperature at 11°C (51°F) or higher for 5 to 60 minutes to complete the refresh charge. (The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode".)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again.

If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A382134E01
0.073,0.073 2.594,0.365 2.521,0.292 12 false w/ Entry and Start System: 2.042,3.688 4.75,3.948 2.708,0.26 10 false Instrument Panel Junction Block Assembly 1.74,5.802 3.406,6.219 1.667,0.417 10 false Certification ECU (Smart Key ECU Assembly) 1.719,5.042 2.135,5.281 0.417,0.24 10 false G69 0.76,5.344 1.531,5.583 0.771,0.24 10 false IG1 NO. 1 2.979,4.625 3.396,4.865 0.417,0.24 10 false G70 2.979,5.385 3.396,5.625 0.417,0.24 10 false G70 5.885,5.875 6.302,6.115 0.417,0.24 10 false G126 3.885,5.76 4.302,6 0.417,0.24 10 false B2 1.771,4.833 2.188,5.073 0.417,0.24 10 false 20 2.104,5.052 2.521,5.292 0.417,0.24 10 false IG1D 3.031,4.427 3.448,4.667 0.417,0.24 10 false 37 3.042,5.188 3.458,5.427 0.417,0.24 10 false 16 2.5,5.375 2.917,5.615 0.417,0.24 10 false STAR 2.573,4.604 2.99,4.844 0.417,0.24 10 false STA 3.885,5.948 5.198,6.375 1.313,0.427 10 false Clutch Start Switch Assembly (for Lower) 0.167,6.5 0.583,6.74 0.417,0.24 10 false A 5.375,6.5 5.792,6.74 0.417,0.24 10 false B 5.917,5.521 6.333,5.76 0.417,0.24 10 false 21 5.917,4.99 6.333,5.229 0.417,0.24 10 false 17 6.188,4.865 6.604,5.104 0.417,0.24 10 false CLL 6.208,5.396 6.625,5.635 0.417,0.24 10 false STA 4.885,5.51 5.302,5.75 0.417,0.24 10 false 1 3.969,5.51 4.385,5.75 0.417,0.24 10 false 2 3.375,0.74 3.792,0.979 0.417,0.24 10 false B1 3.354,0.906 5.677,1.167 2.323,0.26 10 false Clutch Switch Assembly (for Upper) 3.292,0.51 3.708,0.75 0.417,0.24 10 false 1 4.26,0.521 4.677,0.76 0.417,0.24 10 false 2 5.885,6.052 7,6.396 1.115,0.344 10 false Engine Stop and Start ECU 6.198,0.385 6.615,0.625 0.417,0.24 10 false CLU 5.927,0.531 6.344,0.771 0.417,0.24 10 false 11 2.5,1.479 2.917,1.719 0.417,0.24 10 false 2D 2.813,1.49 3.229,1.729 0.417,0.24 10 false 7 1.875,2.24 2.292,2.479 0.417,0.24 10 false 2E 1.875,2.719 2.292,2.958 0.417,0.24 10 false 2F 1.875,3.177 2.292,3.417 0.417,0.24 10 false 2A 2.271,3.177 2.688,3.417 0.417,0.24 10 false 2R 3.521,2.865 3.938,3.104 0.417,0.24 10 false AM1 2.677,1.927 3.563,2.146 0.885,0.219 10 false IG1 NO. 4 1.896,2.958 2.313,3.198 0.417,0.24 10 false 1*1 2.323,2.969 2.74,3.208 0.417,0.24 10 false 1*2 1.917,2.521 2.333,2.76 0.417,0.24 10 false 2 1.917,2.01 2.333,2.25 0.417,0.24 10 false 1 0.479,6.042 1.677,6.292 1.198,0.25 10 false *1: for LHD 0.479,6.344 1.677,6.594 1.198,0.25 10 false *2: for RHD 0.646,4.917 1.063,5.156 0.417,0.24 10 false 3 1.375,4.906 1.792,5.146 0.417,0.24 10 false 5 0.646,5.167 1.063,5.406 0.417,0.24 10 false 2 1.385,5.177 1.802,5.417 0.417,0.24 10 false 1

A382135E01
0.083,0.083 2.167,0.375 2.083,0.292 12 false w/o Entry and Start System: 6.188,0.396 6.646,0.594 0.458,0.198 10 false CLU 5.906,0.542 6.365,0.74 0.458,0.198 10 false 11 3.219,0.75 3.677,0.948 0.458,0.198 10 false B1 3.219,0.948 5.51,1.177 2.292,0.229 10 false Clutch Switch Assembly (for Upper) 1.969,6.156 3.073,6.563 1.104,0.406 10 false Ignition or Starter Switch Assembly 1.979,6 2.292,6.188 0.313,0.188 10 false G1 0.167,6.427 0.479,6.615 0.313,0.188 10 false A 5.375,6.417 5.688,6.604 0.313,0.188 10 false B 0.344,5.771 1.5,6.125 1.156,0.354 10 false STRG LOCK/AM2 NO. 1 0.302,5.167 0.823,5.354 0.521,0.188 10 false ALT 2.052,4.677 2.365,4.865 0.313,0.188 10 false AM1 2.042,5.49 2.438,5.677 0.396,0.188 10 false AM2 2.823,4.656 3.135,4.844 0.313,0.188 10 false IG1 2.813,5.469 3.188,5.677 0.375,0.208 10 false ST2 3.188,4.885 3.5,5.073 0.313,0.188 10 false 8 1.813,4.906 2.125,5.094 0.313,0.188 10 false 5 1.823,5.729 2.135,5.917 0.313,0.188 10 false 4 3.188,5.708 3.5,5.896 0.313,0.188 10 false 2 3.927,5.708 4.24,5.896 0.313,0.188 10 false 2 4.906,5.719 5.219,5.906 0.313,0.188 10 false 1 5.938,5.719 6.25,5.906 0.313,0.188 10 false 21 6.208,5.156 6.521,5.344 0.313,0.188 10 false CLL 6.229,5.583 6.542,5.771 0.313,0.188 10 false STA 3.896,5.948 4.208,6.135 0.313,0.188 10 false B2 3.896,6.115 5.188,6.521 1.292,0.406 10 false Clutch Start Switch Assembly (for Lower) 5.896,5.26 6.208,5.448 0.313,0.188 10 false 17 5.969,6.063 6.406,6.26 0.438,0.198 10 false G126 5.979,6.25 7.094,6.708 1.115,0.458 10 false Engine Stop and Start ECU 4.198,0.521 4.51,0.708 0.313,0.188 10 false 2 3.208,0.521 3.521,0.708 0.313,0.188 10 false 1 1.865,2.229 2.323,2.427 0.458,0.198 10 false 2E 1.865,2.708 2.323,2.906 0.458,0.198 10 false 2F 1.865,3.177 2.323,3.375 0.458,0.198 10 false 2A 2.26,3.177 2.719,3.375 0.458,0.198 10 false 2R 3.521,2.875 3.979,3.073 0.458,0.198 10 false AM1 2.51,1.479 2.969,1.677 0.458,0.198 10 false 2D 2.219,1.49 2.531,1.677 0.313,0.188 10 false 7 2.677,1.948 3.396,2.146 0.719,0.198 10 false IG1 NO. 4 1.958,3.688 5.052,3.917 3.094,0.229 10 false Instrument Panel Junction Block Assembly 1.885,2.01 2.198,2.198 0.313,0.188 10 false 1 1.885,2.49 2.198,2.677 0.313,0.188 10 false 2 1.854,2.969 2.167,3.156 0.313,0.188 10 false 1*1 2.229,2.969 2.542,3.156 0.313,0.188 10 false 1*2 0.438,6.167 1.573,6.365 1.135,0.198 10 false *1: for LHD 0.458,6.448 1.594,6.646 1.135,0.198 10 false *2: for RHD

A382136E01
0.625,5.083 1.698,5.281 1.073,0.198 10 false Battery 0.458,3.417 1.531,3.615 1.073,0.198 10 false FL MAIN 1.031,2.25 2.104,2.448 1.073,0.198 10 false ST NO. 2 1.104,1.469 2.177,1.667 1.073,0.198 10 false ST NO. 1 0.448,0.708 1.521,0.906 1.073,0.198 10 false ALT 0.313,0.125 0.594,0.375 0.281,0.25 10 false A 1.698,4.406 3.188,4.646 1.49,0.24 10 false Starter Assembly 2.625,1.688 3.698,1.885 1.073,0.198 10 false ST NO. 1 4.292,4.531 5.365,4.729 1.073,0.198 10 false ST NO. 2 5.833,2.865 6.281,3.073 0.448,0.208 10 false G125 5.844,3.469 6.292,3.677 0.448,0.208 10 false G125 5.844,4.198 6.292,4.406 0.448,0.208 10 false G126 2.625,2.969 3.063,3.219 0.438,0.25 10 false SL1 2.604,3.854 3.042,4.104 0.438,0.25 10 false SL2 2.688,3.438 3.125,3.688 0.438,0.25 10 false ST 1.75,3.938 2.188,4.188 0.438,0.25 10 false B 1.417,3.917 1.854,4.167 0.438,0.25 10 false D3 4.063,0.125 4.344,0.375 0.281,0.25 10 false B 5.271,5.063 7.052,5.333 1.781,0.271 10 false Engine Stop and Start ECU 6.26,2.875 6.708,3.083 0.448,0.208 10 false GND2 6.26,3.469 6.708,3.677 0.448,0.208 10 false GND1 6.25,4.188 6.802,4.396 0.552,0.208 10 false STA2 2.948,2.969 3.385,3.219 0.438,0.25 10 false C141 2.938,3.438 3.375,3.688 0.438,0.25 10 false C140 2.406,1.031 2.844,1.281 0.438,0.25 10 false 1 3.302,1.031 3.74,1.281 0.438,0.25 10 false 2 3.302,1.438 3.74,1.688 0.438,0.25 10 false 3 2.427,1.427 2.865,1.677 0.438,0.25 10 false 5 3.052,2.74 3.49,2.99 0.438,0.25 10 false 1 3.052,3.24 3.49,3.49 0.438,0.25 10 false 1 3.052,3.667 3.49,3.917 0.438,0.25 10 false 2 1.448,3.698 1.885,3.948 0.438,0.25 10 false 1 2.938,3.854 3.375,4.104 0.438,0.25 10 false C141 4.875,3.99 5.313,4.24 0.438,0.25 10 false 5 4.146,3.99 4.583,4.24 0.438,0.25 10 false 3 4.885,4.313 5.323,4.563 0.438,0.25 10 false 2 4.177,4.313 4.615,4.563 0.438,0.25 10 false 1 5.969,2.656 6.406,2.906 0.438,0.25 10 false 2 5.958,3.271 6.396,3.521 0.438,0.25 10 false 8 5.917,3.99 6.354,4.24 0.438,0.25 10 false 23

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION



HINT:
·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA



PROCEDURE

1.READ VALUE USING GTS (CLUTCH UPPER SW AND CLUTCH LOWER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Clutch Upper SW and Clutch Lower SW.

Powertrain > Stop and Start > Data List
Tester Display
Clutch Upper SW
Clutch Lower SW
50003 227 10,11

e.

Depress the clutch pedal and read the values displayed on the GTS.

OK:
Tester Display Condition Normal Condition
Clutch Upper SW Fully Depressed OFF
Clutch Lower SW Fully Depressed ON
Clutch Upper SW Fully Released ON
Clutch Lower SW Fully Released OFF



Result:
Proceed to
NG
OK



NG

2.INSPECT CLUTCH START SWITCH ASSEMBLY (FOR LOWER)

OK

2.INSPECT CLUTCH START SWITCH ASSEMBLY (FOR LOWER)
a.

Inspect the clutch start switch assembly (for lower).

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT CLUTCH SWITCH ASSEMBLY (FOR UPPER)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY (FOR LOWER)

3.INSPECT CLUTCH SWITCH ASSEMBLY (FOR UPPER)
a.

Inspect the clutch switch assembly (for upper).

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE START AND STOP ECU - CLUTCH START SWITCH ASSEMBLY (FOR LOWER))

NG

REPLACE CLUTCH SWITCH ASSEMBLY (FOR UPPER)

4.CHECK HARNESS AND CONNECTOR (ENGINE START AND STOP ECU - CLUTCH START SWITCH ASSEMBLY (FOR LOWER))
a.

Disconnect the G126 engine stop and start ECU connector.


b.

Disconnect the B2 clutch start switch assembly (for lower) connector.


c.

w/ Entry and Start System:

Disconnect the G70 certification ECU (smart key ECU assembly) connector.


d.

w/o Entry and Start System:

Disconnect the G1 ignition or starter switch assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G126-17 (CLL) - B2-2 Always Below 1 Ω
G126-17 (CLL) - Body ground Always 10 kΩ or higher
B2-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ENGINE START AND STOP ECU - CLUTCH SWITCH ASSEMBLY (FOR UPPER))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ENGINE START AND STOP ECU - CLUTCH SWITCH ASSEMBLY (FOR UPPER))
a.

Disconnect the G126 engine stop and start ECU connector.


b.

Disconnect the B1 clutch switch assembly (for upper) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G126-11 (CLU) - B1-2 Always Below 1 Ω
G126-11 (CLU) - Body ground Always 10 kΩ or higher
B1-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR