When the downhill assist control switch is turned on, the downhill assist control function is available and the downhill assist control indicator light illuminates.
Refer to Downhill Assist Control Indicator Light does not Come ON.
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Check if CAN communication system DTCs are output.
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
| Proceed to |
|---|
| DTC is not output |
| DTC is output |
DTC is not output
DTC is output
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
The connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Remove the downhill assist control switch.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>DOWNHILL ASSIST CONTROL SWITCH>REMOVAL
Inspect the downhill assist control switch.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>DOWNHILL ASSIST CONTROL SWITCH>INSPECTION
The downhill assist control switch operates normally.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A4 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A4-27 (HDCS) - G72-4 | Always | Below 1 Ω |
| A4-27 (HDCS) or G72-4 - Body ground | Always | 10 kΩ or higher |
| G72-1 - Body ground | Always | Below 1 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the A4 skid control ECU (brake actuator assembly) connector.
Reconnect the G72 downhill assist control switch connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Downhill Assist Control Light | Downhill assist control indicator light | ON or OFF | OFF: Downhill assist control indicator light off
ON: Downhill assist control indicator light on |
- |
| Tester Display |
|---|
| Downhill Assist Control Light |
Check the GTS display condition of the Downhill assist control indicator light.
| Proceed to |
|---|
| Display of the Data List remains OFF |
| Display of the Data List remains ON |
Display of the Data List remains OFF
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Display of the Data List remains ON