Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _037980 CRUISE CONTROL _0262559 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1AA7  Skid Control Buzzer Circuit  


DESCRIPTION

The forward recognition camera operates the pre-crash warning by sending a buzzer request signal to the skid control buzzer.

If the forward recognition camera detects a malfunction in the skid control buzzer circuit, it will output DTC C1AA7.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA7 Skid Control Buzzer Circuit When the ignition switch is turned to ON and the pre-crash warning is operating, and one of the following conditions is met:
·

A buzzer request signal is sent to the skid control buzzer but the buzzer does not sound for 1 second or more.

·

A buzzer request signal is not sent to the skid control buzzer but the buzzer sounds for 1 second or more.

·

There is no buzzer sounding request and an open circuit is detected in the skid control buzzer.


·

Skid control buzzer

·

Forward recognition camera

·

Harness or connector



WIRING DIAGRAM

B403796E74
5.031,2.188 6.958,2.5 1.927,0.313 10 false Forward Recognition Camera 3.365,1.188 4.771,1.521 1.406,0.333 10 false Skid Control Buzzer 2.198,0.844 3.24,1.229 1.042,0.385 10 false IG1 NO. 5 3.573,0.698 4.042,0.896 0.469,0.198 10 false IG1 4.229,0.698 4.552,0.896 0.323,0.198 10 false BZ 5.521,0.708 5.844,0.906 0.323,0.198 10 false BZ 0.583,0.688 2.729,0.885 2.146,0.198 10 false from IG Circuit 3.396,0.573 3.563,0.781 0.167,0.208 10 false 2 4.5,0.583 4.667,0.792 0.167,0.208 10 false 1 5.344,0.573 5.5,0.771 0.156,0.198 10 false 8 3.354,1.031 3.813,1.229 0.458,0.198 10 false G129 5.021,2.042 5.479,2.24 0.458,0.198 10 false Q4

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Axis Adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT



PROCEDURE

1.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Perform the Active Test according to the display on the GTS.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1AA7 to be stored if the DTC detection conditions are met.


Chassis > Front Recognition Camera > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Buzzer Skid control buzzer ON / OFF Test possible with ignition switch ON, vehicle stopped
Chassis > Front Recognition Camera > Active Test
Tester Display
PCS Buzzer
50004 386 1

c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AA7 is not output A
DTC C1AA7 is output B



A

B

2.CHECK TERMINAL VOLTAGE
2.CHECK TERMINAL VOLTAGE
a.
B443157C03
1.5,0.177 1.906,0.417 0.406,0.24 1.99,1.333 2.5,1.156 true 0.188,0.156 0.5,0.313 0.313,0.156 10 false *a 1.542,0.219 2,0.417 0.458,0.198 10 false G129 2.552,1.063 3.01,1.26 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control Buzzer)


Disconnect the skid control buzzer connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G129-2 (IG1) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Connect the skid control buzzer connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER - BATTERY)

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - FORWARD RECOGNITION CAMERA)
a.

Disconnect the G129 skid control buzzer connector.


b.

Disconnect the Q4 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G129-1 (BZ) - Q4-8 (BZ) Always Below 1 Ω
G129-1 (BZ) or Q4-8 (BZ) - Body ground Always 10 kΩ or higher



d.

Connect the Q4 forward recognition camera connector.


e.

Connect the G129 skid control buzzer connector.


Result:
Proceed to
OK
NG



OK

6.INSPECT SKID CONTROL BUZZER (CONFIRM BUZZER OPERATION)

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER - FORWARD RECOGNITION CAMERA)
4.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER - FORWARD RECOGNITION CAMERA)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
5.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Perform the Active Test according to the display on the GTS.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1AA7 to be stored if the DTC detection conditions are met.


Chassis > Front Recognition Camera > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Buzzer Skid control buzzer ON / OFF Test possible with ignition switch ON, vehicle stopped
Chassis > Front Recognition Camera > Active Test
Tester Display
PCS Buzzer
50004 386 1

c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AA7 is not output A
DTC C1AA7 is output B



A

END

B

6.INSPECT SKID CONTROL BUZZER (CONFIRM BUZZER OPERATION)
6.INSPECT SKID CONTROL BUZZER (CONFIRM BUZZER OPERATION)
a.

Turn the ignition switch to ON.


b.

Check if the skid control buzzer is sounding.


Result:
Result Proceed to
The skid control buzzer does not sound when the ignition switch is turned to ON A
The skid control buzzer sounds continuously when the ignition switch is turned to ON B



A

7.INSPECT SKID CONTROL BUZZER (UNIT INSPECTION)

B

8.REPLACE SKID CONTROL BUZZER
7.INSPECT SKID CONTROL BUZZER (UNIT INSPECTION)


Result:
Result Proceed to
Skid control buzzer is abnormal A
Skid control buzzer is normal B



A

8.REPLACE SKID CONTROL BUZZER

B

9.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
8.REPLACE SKID CONTROL BUZZER

NEXT

9.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
9.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Perform the Active Test according to the display on the GTS.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1AA7 to be stored if the DTC detection conditions are met.


Chassis > Front Recognition Camera > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Buzzer Skid control buzzer ON / OFF Test possible with ignition switch ON, vehicle stopped
Chassis > Front Recognition Camera > Active Test
Tester Display
PCS Buzzer
50004 386 1

c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AA7 is not output A
DTC C1AA7 is output B



A

END

B

REPLACE FORWARD RECOGNITION CAMERA