Home › Engine / Hybrid System › 2GD-FTV STARTING › STARTER(w/ Stop And Start System) › from 2016.03
RM3250E _51 Engine / Hybrid System _038012 2GD-FTV STARTING _0262617 STARTER(w/ Stop And Start System) A

2GD-FTV STARTING  STARTER(w/ Stop And Start System)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the starter assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative when not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Pre-crash safety system (Click here)
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
w/ Stop and Start System:

Replacement of starter assembly


NOTICE:

When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.


Clear the number of starter operations

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 53882K 3.REMOVE FRONT FENDER SEAL LH

a.

Remove the 6 clips and front fender seal LH.


Hide 51410 4.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442 5.REMOVE NO. 2 ENGINE UNDER COVER

Hide 37140 6.REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)

Hide 41110F 7.DISCONNECT FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

a.
C330144

Disconnect the breather hose from the differential breather tube bracket.


b.
C323253

Remove the bolt and disconnect the differential breather tube bracket.


c.
C323254

Disconnect the hose from the front differential union.


d.
C323255

Disconnect the differential oil temperature sensor connector.


e.

Remove the bolt and disconnect the wire harness.


f.
C323256

Disconnect the differential motor actuator connector.


g.

Remove the bolt and disconnect the wire harness.


h.
A350959

Support the front differential carrier assembly with a transmission jack.


i.
A350894C01
1.875,1.583 2.083,1.344 2.083,1.344 2.365,1.333 true 2.531,0.438 2.74,0.698 0.208,0.26 10 true A 0.958,1.521 1.177,1.74 0.219,0.219 10 true B 2.438,1.292 2.646,1.552 0.208,0.26 10 true *1
*1 Differential Mount Nut


Using a 17 mm ball joint lock nut wrench, loosen bolt A and bolt B.


j.

Using a 12 mm hexagon socket wrench, remove the differential mount nut.


k.

Remove bolt A.


l.
A350892

Remove the 2 front mounting bolts, 2 lower differential mount stoppers and 2 nuts from the front differential carrier assembly.


m.
A350895

Lift up the front differential carrier assembly and remove bolt B and the front No. 3 differential support.


n.
A350893C01
0.688,0.594 1.49,0.344 1.49,0.344 1.302,1.177 true 1.552,0.208 1.865,0.406 0.313,0.198 10 false *1
*1 Upper Differential Mount Stopper


Remove the 2 upper differential mount stoppers from the front differential carrier assembly.


o.
A350896

Lower the front differential carrier assembly as shown in the illustration.


Hide 31485 8.REMOVE CLUTCH FLEXIBLE HOSE BRACKET (for Manual Transmission)

a.
A382860

Remove the clip from the clutch flexible hose bracket.


b.
A382861

Remove the 2 nuts and clutch flexible hose bracket.


Hide 9.DISCONNECT CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transmission)

Hide 77801A 10.REMOVE UREA TANK SUB-ASSEMBLY (w/ Urea SCR System)

Hide 77827A 11.REMOVE NO. 2 UREA TANK FILLER PIPE SUPPORT (w/ Urea SCR System)

a.
A382862

Remove the bolt and No. 2 urea tank filler pipe support.


Hide 28100 12.REMOVE STARTER ASSEMBLY

a.
C323762

Disconnect the 2 starter connectors.


b.

Remove the nut and disconnect the starter wire.


c.

for Automatic Transmission:

i.
C323763

Detach the clamp.


ii.

Remove the nut, 3 bolts and starter assembly and disconnect the ground cable.



d.

for Manual Transmission:

i.
A382863

Detach the clamp.


ii.

Remove the 3 bolts and starter assembly and disconnect the ground cable.