Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2016.03
RM3250E _58 Vehicle Interior _053993 PRE-CRASH SAFETY _0264409 PRE-CRASH SAFETY SYSTEM J

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit supplies power to the millimeter wave radar sensor assembly when the ignition switch to ON.

WIRING DIAGRAM

C279317E11
0.938,0.438 2.156,0.656 1.219,0.219 10 false from IG Circuit 3.26,0.615 4.125,0.833 0.865,0.219 10 false IG1 NO. 5 0.115,2.146 2.208,2.406 2.094,0.26 10 false *1: w/o Stop and Start System 4.823,0.281 5.094,0.542 0.271,0.26 10 false 8 4.792,1.479 5.063,1.74 0.271,0.26 10 false 1 5.042,0.438 5.448,0.646 0.406,0.208 10 false IGB 5.021,1.667 5.573,1.875 0.552,0.208 10 false SGND 4.646,2.073 5.833,2.354 1.188,0.281 10 false A64 4.635,2.271 7.125,2.5 2.49,0.229 10 false Millimeter wave radar sensor assembly 0.75,1.479 2.896,1.781 2.146,0.302 10 false Engine Stop and Start ECU*2 0.365,1.49 0.854,1.76 0.49,0.271 10 false G127 4.052,0.958 4.323,1.219 0.271,0.26 10 false *2 1.51,1.094 2,1.354 0.49,0.26 10 false IG41 1.979,0.979 2.25,1.24 0.271,0.26 10 false 3 0.125,2.448 2.073,2.719 1.948,0.271 10 false *2: w/ Stop and Start System 4.01,0.292 4.281,0.552 0.271,0.26 10 false *1

CAUTION / NOTICE / HINT

NOTICE:
·

w/ Stop and Start System:

As the millimeter wave radar sensor assembly is supplied power from the engine stop and start ECU, make sure that the stop and start system is not malfunctioning before performing the following inspection procedure.

·

w/o Stop and Start System:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY (IGB VOLTAGE)
a.
E325539C66
1.563,0.156 1.938,0.385 0.375,0.229 2.479,1.771 1.958,1.25 true 1.635,0.198 2.094,0.396 0.458,0.198 10 false A64 2.542,1.719 3,1.917 0.458,0.198 10 false IGB 0.125,0.135 0.438,0.292 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A64 millimeter wave radar sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

A64-8 (IGB) - Body ground Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2



d.

Turn the ignition switch off.


e.

Reconnect the A64 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

NG (w/ Stop and Start System)

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
a.
E325539C67
1.563,0.156 1.938,0.385 0.375,0.229 1.417,1.063 0.896,1.708 true 1.635,0.188 2.094,0.385 0.458,0.198 10 false A64 0.698,1.74 1.156,1.938 0.458,0.198 10 false SGND 0.125,0.135 0.438,0.292 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A64 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (SGND) - Body ground Always Below 1 Ω



c.

Connect the A64 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR