Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2016.03
RM3250E _58 Vehicle Interior _053993 PRE-CRASH SAFETY _0264409 PRE-CRASH SAFETY SYSTEM J

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  Pre-crash Safety System Cancel Switch Circuit  


DESCRIPTION

Each time the pre-crash system cancel switch assembly is pressed, the multi-information display sensitivity setting display changes and the sensitivity of the pre-crash safety system changes between 3 levels. Also, when the switch is pressed and held, the pre-crash safety system cancels.

WIRING DIAGRAM

C355870E01
4.76,1.688 6.583,2.083 1.823,0.396 10 false Forward Recognition Camera 4.75,1.521 5.167,1.833 0.417,0.313 10 false Q4 5.344,0.896 5.844,1.229 0.5,0.333 10 false PBSW 5.125,0.74 5.542,1.052 0.417,0.313 10 false 9 2.865,1.521 4.531,1.854 1.667,0.333 10 false Pre-crash System Cancel Switch Assembly 2.844,1.323 3.26,1.635 0.417,0.313 10 false G123 4.031,0.75 4.531,1.083 0.5,0.333 10 false ECU 4.458,0.75 4.875,1.063 0.417,0.313 10 false 8 3.167,0.75 3.667,1.083 0.5,0.333 10 false GND 2.938,0.698 3.354,1.01 0.417,0.313 10 false 5 3.792,3.938 6.542,4.333 2.75,0.396 10 false Millimeter Wave Radar Sensor Assembly 0.615,4.365 2.531,4.615 1.917,0.25 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Axis Adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT

·

When a malfunction occurs in the communication line to the forward recognition camera, U023A and/or U1002 is output. If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>U023A



PROCEDURE

1.INSPECT PRE-CRASH SYSTEM CANCEL SWITCH ASSEMBLY
a.

Remove the pre-crash system cancel switch assembly.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM CANCEL SWITCH>REMOVAL


b.

Inspect the pre-crash system cancel switch assembly.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM CANCEL SWITCH>INSPECTION


c.

Install the pre-crash system cancel switch assembly.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PRE-CRASH SYSTEM CANCEL SWITCH ASSEMBLY - FORWARD RECOGNITION CAMERA AND BODY GROUND)

NG

REPLACE PRE-CRASH SYSTEM CANCEL SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (PRE-CRASH SYSTEM CANCEL SWITCH ASSEMBLY - FORWARD RECOGNITION CAMERA AND BODY GROUND)
a.

Disconnect the G123 pre-crash system cancel switch assembly connector.


b.

Disconnect the Q4 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G123-8 (ECU) - Q4-9 (PBSW) Always Below 1 Ω
G123-5 (GND) - Body ground Always Below 1 Ω
G123-8 (ECU) or Q4-9 (PBSW) - Body ground Always 10 kΩ or higher



d.

Connect the Q4 forward recognition camera connector.


e.

Connect the G123 pre-crash system cancel switch assembly connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform Forward Recognition Axis Adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT


c.

Operate the pre-crash system cancel switch assembly until it turns off.


d.

Check the PCS warning light in the combination meter assembly.

OK:

The PCS warning light will illuminate.



Result:
Proceed to
OK
NG



OK

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

NG

4.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
4.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


c.

Operate the pre-crash system cancel switch assembly until it turns off.


d.

Check the PCS warning light in the combination meter assembly.

OK:

The PCS warning light will illuminate.



Result:
Proceed to
OK
NG



OK

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

NG